1 / 6
Creality chamber heater kit for Anycubic Kobra S1 — image 1
1 / 6

Creality chamber heater kit for Anycubic Kobra S1

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Chamber heater mounting kit for Kobra S1, designed for easy installation (requires drilling, glueing and M3x12 screws)

Rating
0 / 5
Likes
19
Downloads
71
Makes
0
Views
1,582
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Share Alike

To print materials like ASA you need chamber that is thermally stable and often heated up to 70°C, which can be easily achieved with a chamber heater. However mounting it in Kobra S1 is a bit of a hassle as there is not much room to spare. Luckily Creality chamber heater fits fairly well, but measuring out the holes to drill in the sidepanel is a hassle, and the heater mounting hardware (M3 screws) as well as the heater itself get hot and over time can bend and warp the sidepanel plastic.

As such I made a sandwich style mounting kit for the heater. You still have to drill into the side panel, but I also made a version that you can sticky tape in if you wish to go that route (still have to drill and saw holes for the cables tho, but if you want clean sidepanel you may be able to figure out a way to route them differently, I did not and I had no qualms about drilling in the first place).

You will need extra M3 screws, I used M3x12 and washer (Creality includes M3x8 I believe). You can redesign it to fit whatever screws you have on hand, even the stock ones probably, I just wanted heaps of material sandwiching the sidepanel. The inner body (named Chamber body in the files) can be used as a jig for drilling or marking holes into the sidepanel. It is designed for drill bit 6, but I do recommend chasing it with 6.5 afterwards to make the fitting easier. Also the holes in the outside bracket can become too tight for M3 screws, chasing them out with a drill but 3 is recommended.

There is an option for decorative mounting for the outside bracket - it's just three notches in the body to make alignment easier and to introduce extra friction. You can do whatever, e.g. I modeled our cat. Or again you can just slap something on with sticky tape or completely remodel the outer bracket to be decorative in the first place.

Second part of the whole kit is cable cover. You have to cut out fairly large portion of the side panel to route the cables out. I designed a jig that is the "path of least resistance" in my case, it is compatible with both rotary tool and hacksaw. I recommend using sticky tape to lock it in place.

Then the cover is designed as a two part body, where the inner body slides in and locks itself with little nubs. There is a version with cable holder hooks and without. And it is meant to be glued on with CA glue or whatever other glue or epoxy you prefer to use. The inner body is not meant to be glued in, it is designed to be removable in case you want to remove the heater altogether.

The insulation is optional, I just put it in because I had bunch lying around from making winter shelters for strays. I had it for a long time, it's just a foam, sticky tape and Aluminium foil.

The whole kit is designed with 3d printing in mind. There is no need whatsoever for supports. All pieces displayed have been printed in the Kobra S1 with ASA (apart from the decorative bit) by SUNLU.

I can't provide SCAD files since this is designed in Fusion. I am providing f3d files for remixing. You can do whatever with it apart from selling the design itself.

And do not worry, the cat is not allowed to be near the printer/in the same room when it is running and until I air out the room. I do have activated charcoal filter in the printer and dedicated air vent in the room that runs while the printer does but that is never 100% hence the "no living things in the room while printing".

This kit is designed for use with Creality Chamber Heater https://store.creality.com/eu/products/creality-chamber-heater

Tags