3 x 5.25in bay to five 3.5in hard drives cage
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Remixed the SCAD to make a 5 drive version with customizable options.
- Rating
- 0 / 5
- Likes
- 11
- Downloads
- 97
- Makes
- 0
- Views
- 668
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Computers
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
5-Drive 3.5" HDD Cage (3x 5.25" Bay)
This is a high-density, parametric OpenSCAD model designed to fit 5x 3.5" HDDs into a standard 3x 5.25" drive bay stack. This design is an evolution of the proven 4-drive cage by AnthonyZ71, optimized for the maximum possible storage density (5 drives) while maintaining structural stability and cooling.
⚠ CRITICAL: The "0.1mm" Challenge
Fitting 5 drives into a 146.1mm wide bay is mathematically at the limit. After accounting for the 5 drives and the 7.5mm structural side walls, you are left with only 0.1mm of total clearance.
DO NOT skip the test print. Open
cage_5drive.scad, setPART = "single_slot_test", and print it first. If your rail doesn't slide in smoothly, you must adjust thetoleranceparameter in OpenSCAD before committing to the 18-hour main cage print.
🛠 Features
Maximum Density: Fits 5 full-sized 3.5" HDDs in 3 bays (Maximum limit).
Parametric: Supports configurations for 3, 4, or 5 drives (defaulted to 5).
Fan Support: Integrated shroud for 120mm or 140mm fans with multiple grill styles.
Mounting Styles: Toggle
fan_mount_stylebetween Heat-Set Inserts ("heat_set") or Snap-Pins ("snap_pins").Maximum Airflow: Completely open-back design for high-RPM drives.
📦 Print Settings & Parts List
Set the PART variable in OpenSCAD to render each component:
Part Name (PART) | Qty | Material | Settings | Orientation |
| 1 | PETG / ABS | 0.2mm layer, 3-4 walls, 25% infill | Back flat on bed |
| 10 | PETG | 3 perimeters, No Supports | On edge (long side down) |
| 1 | PETG / PLA | 0.2mm layer, 20% infill | Face down |
| 1 | Same as Cage | Same as Cage | Print this first! |
| 4 | PETG | 100% infill | Only for |
Note: PETG is highly recommended for the cage and rails to handle drive heat and provide the necessary "spring" for the rail tabs to lock into place.
⚙ Calibration & Parameters
If you need to customize the fit, adjust these key variables in the code:
drive_count: Default is 5. While the code allows lower numbers (3 or 4), 6 drives will not fit within standard 5.25" bay dimensions.tolerance(Default: 0.1mm): The most important setting.Too tight? Increase by 0.05mm.
Too loose? Decrease by 0.05mm.
spacing_w: Set to 7.5mm. This is required for 5 drives. Do not reduce this or the cage walls will become structurally unsound.insert_depth: Defaults to 10mm. Ensure your screws are long enough to utilize the full depth.
🔧 Assembly & Hardware
Calibration: Attach rails to an HDD and test in the
single_slot_testprint. Adjusttoleranceuntil the fit is snug but smooth.Inserts: For
"heat_set"style, use 4x M3 inserts (5mm L, 4mm OD) in the front bosses.Fasteners: * Rails: 20x M3x5mm flat-head screws.
Fan Shroud: 4x M3x10mm screws.
Case: Standard M3 fine-thread computer case screws.
❓ Troubleshooting
"Rails are snapping": You likely printed them flat. They must be printed on their side (edge) so the layer lines run the length of the tab.
"Won't fit in case": Verify
cage_win the OpenSCAD console is 146.1mm. If your printer over-extrudes, the cage will be too wide for the bay. Check for internal case tabs that may need flattening.
Credits: Based on the original 4-drive design by AnthonyZ71. Fan grill logic by OutwardB. Snap-pins by Emmett Lalishe.