1 / 11
3 x 5.25in bay to five 3.5in hard drives cage — zdjęcie 1
1 / 11

3 x 5.25in bay to five 3.5in hard drives cage

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Remixed the SCAD to make a 5 drive version with customizable options.

Ocena
0 / 5
Polubienia
11
Pobrania
97
Wydruki
0
Wyświetlenia
668
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

5-Drive 3.5" HDD Cage (3x 5.25" Bay)

This is a high-density, parametric OpenSCAD model designed to fit 5x 3.5" HDDs into a standard 3x 5.25" drive bay stack. This design is an evolution of the proven 4-drive cage by AnthonyZ71, optimized for the maximum possible storage density (5 drives) while maintaining structural stability and cooling.

⚠ CRITICAL: The "0.1mm" Challenge

Fitting 5 drives into a 146.1mm wide bay is mathematically at the limit. After accounting for the 5 drives and the 7.5mm structural side walls, you are left with only 0.1mm of total clearance.

DO NOT skip the test print. Open cage_5drive.scad, set PART = "single_slot_test", and print it first. If your rail doesn't slide in smoothly, you must adjust the tolerance parameter in OpenSCAD before committing to the 18-hour main cage print.

🛠 Features

  • Maximum Density: Fits 5 full-sized 3.5" HDDs in 3 bays (Maximum limit).

  • Parametric: Supports configurations for 3, 4, or 5 drives (defaulted to 5).

  • Fan Support: Integrated shroud for 120mm or 140mm fans with multiple grill styles.

  • Mounting Styles: Toggle fan_mount_style between Heat-Set Inserts ("heat_set") or Snap-Pins ("snap_pins").

  • Maximum Airflow: Completely open-back design for high-RPM drives.

📦 Print Settings & Parts List

Set the PART variable in OpenSCAD to render each component:

Part Name (PART)

Qty

Material

Settings

Orientation

cage

1

PETG / ABS

0.2mm layer, 3-4 walls, 25% infill

Back flat on bed

rail

10

PETG

3 perimeters, No Supports

On edge (long side down)

fan_shroud

1

PETG / PLA

0.2mm layer, 20% infill

Face down

single_slot_test

1

Same as Cage

Same as Cage

Print this first!

fan_mounting_pin

4

PETG

100% infill

Only for snap_pins style

Note: PETG is highly recommended for the cage and rails to handle drive heat and provide the necessary "spring" for the rail tabs to lock into place.

⚙ Calibration & Parameters

If you need to customize the fit, adjust these key variables in the code:

  • drive_count: Default is 5. While the code allows lower numbers (3 or 4), 6 drives will not fit within standard 5.25" bay dimensions.

  • tolerance (Default: 0.1mm): The most important setting.

    • Too tight? Increase by 0.05mm.

    • Too loose? Decrease by 0.05mm.

  • spacing_w: Set to 7.5mm. This is required for 5 drives. Do not reduce this or the cage walls will become structurally unsound.

  • insert_depth: Defaults to 10mm. Ensure your screws are long enough to utilize the full depth.

🔧 Assembly & Hardware

  1. Calibration: Attach rails to an HDD and test in the single_slot_test print. Adjust tolerance until the fit is snug but smooth.

  2. Inserts: For "heat_set" style, use 4x M3 inserts (5mm L, 4mm OD) in the front bosses.

  3. Fasteners: * Rails: 20x M3x5mm flat-head screws.

    • Fan Shroud: 4x M3x10mm screws.

    • Case: Standard M3 fine-thread computer case screws.

❓ Troubleshooting

  • "Rails are snapping": You likely printed them flat. They must be printed on their side (edge) so the layer lines run the length of the tab.

  • "Won't fit in case": Verify cage_w in the OpenSCAD console is 146.1mm. If your printer over-extrudes, the cage will be too wide for the bay. Check for internal case tabs that may need flattening.

Credits: Based on the original 4-drive design by AnthonyZ71. Fan grill logic by OutwardB. Snap-pins by Emmett Lalishe.

Tagi