Liczymy pasujące modele…
Here are four straight rails that can be used with Gravitrax, each spanning 1 to 4 tiles. The length is approximately equivalent to that of the original Gravitrax rails. Note : I'll be uploading separately some rails that are 1 to 3 mm…
Because my Picatinny rail was too short and the standard off-the-shelf Lens-Protectors did not fit, I designed this shorter version. (mounted on a Tavor T21) The lens is taken over from the normal lens protectors that can bought e.g. on…
These are available in 1, 1.5 and 2 degree pitch options. i recommend trying 2 degrees for 70-100fps, 1.5 degrees for 100-150, 1 degree for anything above that. a 30mm raiser is included for blasters with a very flat top like the nexus…
I print lying down with supports. The track doesn't need to be supported, but the fibres may come loose.
print as shown in the picture, use of Trees (Organic) with support to bed only works best
A remix of @shoelesshistorian's updated Swoopy Picatinny AFG, with closer bolt spacing so that it works with rails with only 3 or 4 grooves. Specifically based on the stubby/small version of the original.
Printable rack rails and matching 6mm nuts and bolts to mount your (lightweight) equipment in 10" DIY racks There are lots of options for printable rails out there, but I wanted something where I could mount side panels and have…
About This is still a work in progress so any feedback and/or remixes that improve it will be highly appreciated. It should fit similar machines with little to no modification, as long as the base plate for the bed is the same and the Y…
I haven't had the chance to try it yet. Just a little edge reinforcement using the Shell tool.
Mega Barrel for the Pick-Rocket 2 X-Shot Skins Menace Remix After seeing the model and remembering that the menace could launch Megadarts (tnx @Corvus_1914958), I knew there was more potential being left on the table. Someone just had to…
Adjustable anti-backlash adapters for the X and Y axis on the 3018 CNC. Y axis fits stock set up. X axis fits with upgraded Z axis and MGN12H adapters. See my other files for those.
I wanted to (well my wife wanted me to) mount my 10" rack to get it out of the way, and so I wanted to put it on the plywood near my fiber coming in from the street and my core switch. But did didn't want to put a shelf up just for this,…
I took the V3 SE rails mod and applied all the changes from the comment section. @RainMk_1581311 flattened the model for aesthetic reasons, and removed the tall “guides” that sit around the rails, which possibly restrict the carriage…
A rail to make adding stuff under your table easier… I recommend you print the screws at 100% infill, they sometimes snap when printed at lower infills, also you might need pliers to twist them into place, the tolerance is quite low The…
For the conversion you will need: Size How many What to replace it with Screw (DIN 912) M3x25mm 4 pieces Screw (DIN 7991) M3x8mm 8 pieces Hexagon nut (DIN 934) M3 8 pieces Rail with block assembled (MGN12H) 300mm length 2 pieces Front and…
Updated 5th Nov 2025 Add a sideways mounting option to show off the bookend designs better and a base to allow use as a book-nook. Updated 14th June 2026 Add pre-supported option for side mounting These files comprise the mounting rail…
Replacement for broken holders. Asymmetrically printed to accommodate larger glasses. Printed with ABS for better stability
(SuperFlux or HyperCore) with Big Tire (11.5"/12") to XR rail carrier blocks modified to match the style of OG XR PubHubs. Thanks to @viperbite for help with getting the cover M2 bolts placed nicely. The primary features: A clamp - aims…
On the wooden Ikea Trofast storage combination ( https://www.ikea.com/de/en/p/trofast-storage-combination-with-boxes-light-white-stained-pine-white-s39574865/ ) , the boxes tend to slide out of the groove and get blocked. These small…
STL files for monorail beam compatible with Disney HO monorails: 500 mm radius, 300 mm radius, straights, pylons Newer monorails with operating doors require coupler modification to run on the smaller radius curves. Older models should…
231223 Train rails track switch FemaleMale and MaleFemale, 火車軌道軌道開關 母公母, ट्रेन रेल ट्रैक स्विच महिला पुरुष और पुरुष महिला Added the track switches to be able to make more executions. Already posted Male, Female part, double length and…
I finally created a systainer rail for my older Festool systainers that have been stacked up on the garage floor for too long. They work great and of course they are way cheaper than buying the Festool brand rails. I used all of my old…
I designed these simple rails to allow me to store a stainless steel pan, the IKEA Koncis 34 x 24 cm under my workshop desk and also use it as a drawer for keeping some of the tools and the drip tray for my SL1S. The idea is that the pan…
Simple insert for game Trails with sleeved cards. Jednoduchý insert pro hru Parky: Na cestách s obalenými kartami.
Decided to make the model for the whip Scherazard Harvey uses in the Trails series. The weapon differs slighly from render to render and from ingame moments. Decided to base it mostly of the in game model of Trails in the sky first…
4/27/26: Added straight sections scaled for 10mm LED strip per user request These are simple glue-on rails for the popular fantastic QIDI Q2 riser found here ( https://www.printables.com/model/1398127-qidi-q2-riser ) I modeled to fit 8mm…
Available in three sizes S , M , L to match different rail lengths and storage needs. Each drawer requires 4 magnets (Ø5 mm × 2 mm) to keep the drawer securely closed.
Mini fender, mud guard, and DTF base piece, all in one! For X10 rail angles with BTG tire. Fits both the raised and lowered rail positions with the TFL Thundercat BTG tire. Larger tires or offset (raised AND lowered position) may require…
Mini fender, mud guard, and DTF base piece, all in one! For X7 rail angles with 11in tire, Fits both the raised and lowered rail positions. Larger tires or offset (raised AND lowered position) may require modification to the riser. This…
For english list below.. Vytvořil jsem držáky standardní 3l boxů z obchodu pepco, viz štítek Držáky jsou: jednostranné, pro použití samotného boxu. Oboustranné pro kombinaci 2 boxů poblíž Lze použít 2x jednostranné + 1 x oboustranné, viz…
I made this remix, poorly. for ender3 pro with 320mm linear rails. also made it so the endstop can be used on the tap. so I can you Filamatrix/Filametrix on the left side. don't use supports has built in supports.
The original sideboards & handrails are often broken off by the time you find one of these Tyco Maintenance Wagons for sale on ebay or at a train show. I've carefully modeled replacements based on the appearance of the single original…
Hooks, feet, and rails for a badminton club peg rota board. 19/11/25 V1: Designed the hook around the 4cm tall feet. Assumed the thickness of the sports hall movable wall to be about ~2cm at maximum. Designed peg rails around these pegs .…
Rokenbok handrail custom sizes. Prints best laying flat (as shown in photo) I plan on adding more variants in the future.
Simple mounting plate. BOM: - 4pcs M3x8 - 2pcs self tapping screws 2x10
Modular Wall Rack System – By Xavi V PRINT WALL RAILS AT 30% OR MORE INFILL FOR STRENGTH This fully modular wall rack system is designed to help you organize and store a variety of items, including tools, electronics, wires, and small…
Update 08Feb2026 - Side filament sensor is replaced with new version with switch for TPU. Uses Prusa's design idea. I had rattling sounds at resonant speeds on my Core One. I narrowed down the Y Bearings as a root cause and decided to…
Tired of having your Gravitrax rails to take an awfull lot of space? Tired of having to sort them out each time you need a specific one? This model is for you. Effective & practical way to organize your Gravitrax rails (size 1, 2, 3) with…
Tired of having your Gravitrax rails to take an awfull lot of space? Tired of having to sort them out each time you need a specific one? This model is for you. Effective & practical way to organize your Gravitrax rails (size 1 & 2) with…
Praktický kluzák na záclony je ideální pro vaše vnitřní lišty z plastu a je 30 mm vysoký10 mm široký a 2,5 mm tlustý. Pokyny pro tisk: Výška vrstvy: 0,15 mm Výplň: 10 % Kubická adaptivní Perimetry: 2 Horní/spodní vrstvy: 5/4 Pozice švu:…
Rails set made for the Siku 1011 tram of my sun, scale 1:87 (H0). Rails are ca 11,4mm apart (insides) and 10cm long. For the end parts you need to push the bar into the base. The joints are tight and need a bit of force to connect the…
Installed linear rails to get rid of flexing of the workplate of my Snapmaker 2.0. The rail holders screw into the base of the linear modules, allowing an installation without drilling the base. This model is a re-design/remix to fit…
I used .15 but 2 will work I'm sure. 15 infill 4 layers just for strength organic tree support
All the connectors I've used didn't fit me in some way. That's why I created this one with flexible heads that fits perfectly.
Please refer to the original model for overall notes! All credit to the original maker for the design - I just tweaked it for the hardware I have available on hand. The jigs included in the original model file, with the exception of the…
This is an alternate compact 4U rail compatible with Maurício Pessoa's 3D Printable Rack System as linked below. Please see the link below for all print settings, required parts, and instructions.
Caps to snap-fit onto the end of the rails to prevent bins from accidentally sliding off
Simple mount to install two IKEA Vidga rails with the end to a wall. You need the following parts. 1x M4 40 mm wood screw with dowel. 1x M4 10 mm washer 4x M4 nut 2x M4 8 mm Allen screw 2x M4 grub screw The model was created with FreeCAD…
needed a scope and this one looked really good and i found a picatinny mount and just merged them
What is new in v2: Shorter brackets for better strength The hexagons were removed so that something could be placed on the side rails
Basic shroud for XS CL, made in F360. I printed this but it didn't fit properly, so this newer version should allow a little wiggle room. Included both longer and shorter pieces, long one is about twice the size of the stock barrel. Print…
fully designed this parts by myself, but this guy is a genius — visit his site as well. Phaetus Dragon Hotend HF : )
Made these rails to install seagate SAS drives in the 4-in-3 | 3.5"/5.25" HDD bay mount model. Recommend in PETG!
A hanging shave stand that fits a DE razor and brush. Made to fit on an Ikea kitchen wall rails but may fit on others. This design has a slight offset from the wall to make up for my tiles but should work on a flat wall as well. The V…
Print it with the front or rear on the build plate and use supports for the QD cup itself. Bridging is enough for the M3 hardware. Perimeters: 4 Infill: 100% but 20% is probably fine.
The American Rocketry Challenge uses standard 1 inch rails to guide rockets into the sky. This model allows for prototyping rockets on those rails, without needing to purchase them. These rails follow very close to actual 1010 rail…
Wall mounted rails that hooks slot onto Perfect for keys, wires, and other objects
I have a ZeroG Mercury One.1 printer with X and Y axis linear rails. I needed a sensorless homing bumper/stop block that I could mount on top of the Y axis rail. But, since I use steel plate corner brackets to stabilize my frame, I could…
Fits SynthRacks 84HP EuroRack Rails using the M5 csk bolts they supply.
Note: these ears take up 4.5 rack U.
The Airbus A320 Pedestal as part of Sim Guy A320's project has a fairly complex rail for the top (well Airbus has a fairly complex rail for the top) and I decided to make a easily printed model. It has fairly large pieces (bed size >=…
Mini fender, mud guard, and DTF base piece, all in one! For MatixBuilt rails with BTG tire. Larger tires or offset (raised/lowered position) may require modification to the riser. This interfaces with the GT XL/BTG fender, not the regular…
This is a dart shield that improves cosmetics so that you can fight with style. Supports needed. Enjoy!
Ever got tired of kitchen utensils being everywhere or entangled in a stationary holder? I told myself to stop with it. After thinking of several mounting system, I realized - why not to use RIS rails? These are perfect for such…
This is a 3S battery pack for the QRP Labs QMX Transceiver. It holds 3x Li-ion packs I purchased from Amazon. It also includes rails to protect the front panel knobs. If I don't count the rails, the battery pack only adds 8mm to the…
This is a two-part rotating cable chain attachment for Neptune 4 Max with linear rails. The base mounts to the linear carriage (requires 3mm longer screws than provided with the linear rail kit), and the cable carrier has a "gate hinge"…
Made this to mount back to back DIN Rails remixing the model. There is a thru hone option and a screw into option.
A rail system to quickly bolster a 2.2mm-thick height-adjustable desk with a lot of fun objects to declutter and organize its space! Rail-based system.
My printer can't quite fit the large inclines (p&q), but we do have some of the inclines that don't have supports. so, I chopped up parts from jayftee's train tracks set to make a properly sized riser. It's hollow and prints without…
This is a remix of the case Raspberry Pi 4 Case Mount by Farathus for the Raspberry Pi 4 case with break-out GPIO tab + fan versions by Harryb1991 I lengthened the rails on the original mount as I'm using it underneath a table and wanted…
It's printed rails for the Seagull, not much to explain. No extra hardware needed, just the screws attaching the stock rails. Multiple versions for each position for aesthetics; not every version is guaranteed to still be compatible with…
I designed one support rail with an edge/guide at the left side (for proper alignment of the cutting mat) and a generic rail without edges to be used in the middle and at right side. Each rail comes with two parts for easy and stable…
Designed myself some cable tie rails for mounting my cables underneath my desk. There are many similar versions out there. Designed to me mounted with 4mm sink head wood screws.
Tricky Rails and Sins of Our Fathers are trick taking games designed by Daniel Kenel. Each of these games utilize a 37 space hex board. The game and rules for Tricky Rails can be found here . The game and rules for Sins of Our Fathers can…
These saddle rails can be used to prevent many bike saddle clamps from falling apart when there is no saddle mounted. This can be useful for storage and transport. I have provided both 7x7 and 7x9 versions of the design for alloy and…
Spacer to use 300mm Rails on the SV05 frame for Mercury One.1 conversion
3 piece set. Garden stake can be used with or without extension. For Blink Outdoor (3rd Gen) camera.
Mount limit switch with two M3 x 6mm (or 5mm) button head screws. No supports are needed if printed as shown.
This mod fixes K1 Max quality issues, namely excessive ringing/echo. It also increases maximum accelerations. This mod changes print area depending on options you select, beware. I'll only upload cad assembly here (too many files to…
This anchor-shaped clip is a practical and stylish accessory designed specifically for boat enthusiasts. Perfect for drying clothes or swimsuits, it clips securely to the rail of a boat. The clip features a classic anchor design, adding a…
A grip I modeled after the Nerf Raider/Rampage that attaches to picatinny rail. It's not an exact 100% one to one of the grip but it's as close as I can get, and it feels the same in the hand. It's my favorite pump grip Nerf has made, and…
English: Translated with DeepL.com: There are three individual models: Holder for Nintendo Switch charging station Holder for Nintendo Switch controller Holder for hand strap/rail Nintendo Switch All three models are mounted on a dual…
print with the side that has the clips on the bottom for best results. enjoy!
Style A = Has mounting holes for screw-mounting Style B = No Holes for mounting with double-stick tape Uses 15mm (0.6") glass marbles that need to be inserted before the print finishes, ideally right as the opening is just beginning to…
# Spool support for a 3d printer spool. Designed to sit on shelving rails (mine are from homebase) Customisable to your needs via openscad I used 2x 608 bearings that I press fit in the roller and some 8mm threaded rod to go through it.…
When moving some Eurorack gear into a 19" server style rack, I noticed the 84hp frames that were supposed to fit left ~4hp in wasted space on the sides. So I bought some 104hp Synthrotek rails and cut them down to 17 ⅝" (88hp) to give…
This housing is designed to fit the PWM controller shown in the image, which can be found on Amazon . It also accommodates other switches, provided they fit. This housing is ideal for controlling devices like a cooling fan and is…
An adaptation of ‘SurfinBirdmans’ rails for the Yaesu-857 which adds a 5cm extension to the rear of the radio to provide more space for cable management, useful if being stored vertically in a backpack.
Remix changes the Bed Plates to fit the smaller MGN12C rails
So ... As promised a few weeks ago, here comes my own version of a hotend for the Titan Aero. See it in Action: In Action: https://www.youtube.com/watch?v=Xlx7dZzM6mo The goal was to save weight and above all to save in width, because the…
Simple hilt i designed and recently improved. takes 10/32 heat set threaded inserts for attachment into the rail!
Dies sind Austausch-Schienen für eine Glas-Schiebetür, Marke unbekannt. Dies ist keine 1:1-Kopie, sondern stellt nur die Funktion wieder her und ist etwas robuster gehalten als das Original. Das Modell funktioniert in PLA, aber…
My CAD version if Fungineers Funwheel Thunder rails had just one height. Yes is exactly recreating the Thunder rails model but without 3 heights (just the middle height), logo and the horrible middle section. And no, these are not TFL…
I wanted to mount my joystick and throttle stick hanging upside down under a shelf to save some desk space, and I have found a nice way to achieve it using 3D printing, few screws and a bit of glue. All my tests went far better than…
H0 Tunnel 1:87 works for Märklin C-Gleis and other brands like Roco, Fleischmann, Piko. H0 Tunnel, single track, with small windows and without windows, connectable with connectors. Length of the tunnel is 195mm (~7.7in). Caution: It is…
This is a set of game item holders (card and resource cube organizers, player boards) for TRAILS board game. It was designed to neatly fit into the original game box space. Card holders have cutouts so that it's possible to easily grab…
I have NOT tested this to see if everything works properly yet! I included the STEP file in case anyone is way smarter than me in this regard and can correct any mistakes I've yet to realize. I have been working on getting all the parts…
These Side Rails attach to the sBitx V3 and help protect the Knobs and Screen Area. They attach using the existing screws. Note: These are NOT CARRY HANDLES! If using the Foot Stands like the ones shown in the pics… You'll need the…
These are 5° pint pub rails. These rail files are intended to be sent in to services like JLC3dp or pcbway to be machined out of aluminum. You could also use them for mock up in cad to design other parts around. I have had these rails…
Easy to implement fix to the wooden Trofast. Stops the drawers from jumping off the shelf. It also reduces the friction between the drawer and the shelf My print settings: PLA 0,4 mm nozzle 0,2 mm layer height 3 walls Inner/outer order !…
![Table Rails For Addons [plus a bin i added now but i am too lazy to print...]](https://media.printables.com/media/prints/d3a0c167-84cc-41bc-9f00-d32905b5ad7b/images/10507436_8417ab99-fc49-4a0b-b887-5d6850edf69f_87c2fd22-fe6a-4b44-b315-cf3c3ef83482/img_20250822_145650154.jpg)
