P
Printablessmlimbach
DIN Rail Keystone
For whatever reason, the original was way too loose on my DIN rail, so I remixed it to fit way better, at least on mine!
- Pobrania
- 991
- Polubienia
- 154
- Ocena
- 4,56
Wyniki wyszukiwania: rail
Liczymy pasujące modele…
P
PrintablesJayBird_25
Model Train/Railroad Picnic Table
This is a picnic table created for an o-scale 1:48 model train layout. It can be scaled to fit any other scale or just printed for decoration - (ho scale is 50% scaled, and n scale is roughly 25% scaled). Printing Instructions (Standard):…
- Pobrania
- 331
- Polubienia
- 40
- Ocena
- 5
P
PrintablesBobtheGreatII
Eurorack Side Rail Brackets
Included are two styles of side brackets for your own DIY Eurorack case and its Gie-Tec rails. Both the 3U and 1U (Intellijel) brackets include countersunk holes for M5 flathead screws for mounting the rails, and M3 flathead woodscrews…
- Pobrania
- 133
- Polubienia
- 18
- Ocena
- 0
P
PrintablesBootjevaarder
Kato Unitrack Rail Clips
KATO Unitrack Rail Clips. To secure the rails to the building plate without glueing the rails themselves Printing I printed with PLA, 0.2 mm layer height. Assembly Slide the clips under the rails. Use glue under the clip or screw the…
- Pobrania
- 109
- Polubienia
- 15
- Ocena
- 5
P
Printablesnerd_zentrale
Auto Adjusting MFT Rail Hinge
I recently built a crude rail hinge to get repeatable square cuts on my modified Masterwork table. I was however not happy with the adjustment mechanisms of the first iterations. Looking at the market, there was no suitable acessory for…
- Pobrania
- 106
- Polubienia
- 74
- Ocena
- 0
P
PrintablesAinon3Dtisk
Perfect Family for a diorama or model railroad
Hello, I have the Perfect Family for your diorama or model railway. The figures are now in 1:15 scale. Here is the conversion for model railways, so you know how to adjust the scale: Scale Reduction Approximate height of the figure (cm) G…
- Pobrania
- 90
- Polubienia
- 11
- Ocena
- 0
P
PrintablesGodzilla Guy
Interlocking Socket Rail 3/8 (Added Magnetic)
This is a simple socket set rail that I made for 3/8in drive sockets. It can interlock end to end. The spots for sockets are farther apart the farther down it goes. This fits 8 sockets, ~8-16mm is the best fitting from my experience.…
- Pobrania
- 86
- Polubienia
- 10
- Ocena
- 0
P
PrintablesCertified Cursed
RIS/PICATINNY Rail ASG
RIS rail 91mm that i made for personal purposes.
- Pobrania
- 66
- Polubienia
- 6
- Ocena
- 0
P
PrintablesNick Thom
Railroad rail
Model was made from profile found on Wiki of the New York Central System Dudley 127 lb/yd (63.0 kg/m) rail Full scale Depth is 10" and 7" tall Not sure what to do with it yet thinking of making some fun shelf bracket covers with it for…
- Pobrania
- 63
- Polubienia
- 6
- Ocena
- 0
P
Printables8lall0
Eurorack rail
This is a simple base model for an eurorack rail which fits a M3 threaded rod inside. It's just 1cm, you can extend it inside your slicer. I've added also a connector to make multiple rail connectors sturdier. You should put inside it M3…
- Pobrania
- 58
- Polubienia
- 12
- Ocena
- 0
P
PrintablesAurel3DMaker
Clothes rail holder
Missing a clothes rail holder or broke the original one? I’ve got you covered 🙂 This holder was designed to be stronger than most existing solutions , with an extended rail support area to improve strength and long-term durability. Solid…
- Pobrania
- 41
- Polubienia
- 14
- Ocena
- 0
P
PrintablesMižufko
TrackVision - The Open Railway Project
TrackVision - The Open Railway Project Welcome to the TrackVision ecosystem! This is a comprehensive, custom-designed model railway project built from the ground up for makers. It features a unique, non-standard scale engineered…
- Pobrania
- 21
- Polubienia
- 4
- Ocena
- 0
P
PrintablesZeyrox
Raiser for Picatinny Rail
My flashlight didn't fit on my picatinny rail so I made a raiser for it. Fits every 20mm Picatinny Rail. I made two versions; One to mount it with a screw and the other to print it a little undersize so you can just push it onto the rail.…
- Pobrania
- 19
- Polubienia
- 2
- Ocena
- 0
P
PrintablesstudioTijn
Kitchenware rearangable rail-hooks
Use a cable tray - cover of 30mm widht and patch/glue it to the kitchen tiles. This creates a rail for different hooks to be snapped in. Configure to your own desire and slide to rearrange positions or remove unused items.
- Pobrania
- 19
- Polubienia
- 5
- Ocena
- 0
P
PrintablesBigDumb
Precision Defined Socket Rail 3/8" Ratchet Mount
Print with supports only touching build plate so you have an easier time removing it. I would also recommend printing with more than 60% infill because the handles of 3/8" ratchets are long, which can lead to high torsion. Category: Tool…
- Pobrania
- 18
- Polubienia
- 3
- Ocena
- 0
P
Printablessibj
Clothing rail hook
Made for a clothing rail with 19.2mm diameter
- Pobrania
- 14
- Polubienia
- 3
- Ocena
- 0
P
PrintablesBen Calcott
Railroad Signs
Some signs I drew up to go next to the track when running live steam trains. The V block is designed to take 5mm heat set inserts. There are whistle board, yard limit, and railroad crossing signs.
- Pobrania
- 14
- Polubienia
- 3
- Ocena
- 0
P
PrintablesFrank 3D
Braille Tile Trays
I designed these to work with the braille tiles. One of them just happens to work well with a known word board game…… Designed in Solidworks
- Pobrania
- 10
- Polubienia
- 5
- Ocena
- 0
P
Printableshectare3D
Connectable pull door rail slope
A step-eliminating slope for overcoming three door rails. It has a total length of 40 cm and can be connected. This slope can be used when the rail spacing is 2.1 cm. I will upload a Fusion 360 file, so feel free to customize it. The…
- Pobrania
- 6
- Polubienia
- 5
- Ocena
- 0
P
PrintablesKenny the Maker
Barrel model for model railroading.
Barrel model for model railroading.
- Pobrania
- 5
- Polubienia
- 1
- Ocena
- 0
P
Printables
Pen, USB, SD holder for Fredde desk rail
Desk rail pen holder for Fredde desk. Needs 6mm hook and loop strap to hold in place. Smaller holes will fit Lamy Safari pens, large fit Lamy Al-star. Print low density with two perimeter layers, or whatever your machine likes best, most…
P
Printables
SKR 3 EZ Motherboard mount + Slim mount. Heat Inset 3m. X rail (Milo 1.5)
This is a motherboard mound for the Milo 1.5 with the same exact spacing as the LDO kit fly board comes with. You can keep the t-nuts in the same exact location. Small 3m heat inset from the back. Opening is 5mm for the heat insert
P
Printables
Trailer Plug Holder
This 3D-printed mounting bracket is designed to securely hold a trailer plug using a convenient snap-click mechanism. It is mounted directly onto the trailer, ensuring that the plug stays in place, protected from movement during travel.…
P
Printables
Oh-so-Stylish MK4/MK4S Extrusion Rail Covers (a PRUSA CHALLENGE print)
I started with John 's Cable Cover for Prusa MK4/MK4S/MK3 model, but that did not work well for me. The extrusion rail cover segment was oversized (overhanged the edge), and that poor neuron that had finally achieved some reprieve over…
P
Printables
VZ.61 Off the Top of my Rail
Full Top Rail 0.2 Layer Height 99% Infill Supports Yes M5x30mm and M5 Nut needed for Front M5x16mm and M5 Nut need for Top Rail to Rear Rail Attachment. 2 Screws needed for Rear end Receiver (Metric or Standard Depending on…
P
Printables
Ender 3 V2 Neo linear rail alignment bracket
Since you can't use T-nuts on an Ender 3 V2 Neo to install a lineair rail it's required to drill the X-axis profile This bracket centres the linear rail on the X-axis so it can be drilled correctly. Required tools: hand drill 3.5mm drill…
P
Printables
Krytac P90 Airsoft side Picatinny Rail
Krytac P90 Side picatinny rail. in thre different versions: Cilinder head, Sunken head and button head screws. Walls: I suggest at least 4 Infill: anything over 20%
P
Printables
Trailer plug cover 13 pins.
Protective cover for trailer 13 pins plug. Recomended print: Layers: 0.2 Perimeters: 4 Infill: 5% gyroid Material: recomended ABS, ASA, maybe PetG.
P
Printables
Picatinny rail for CZ75 D
Remix of Ben49's design. Resized to fit on compact CZ 75 D. The rest remains unchanged. Still needed M5 nut and M5x35 CHC screw. Print instructions Category: Sport & Outdoors Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No…
P
Printables
Hacken für Kleiderstange / Clothes rail
Gedruckt aus ABS mit 4 Wandlinien, 0.4mm Linienbreite, 0.16mm Schichthöche, 20% Infill
P
Printables
Tactile Dice / Braille Dice (No supports needed)
Tactile/braille dice, can be printed on the bevel (look at the picture), no support needed. Square side 30 mm. The transparent version is petg, scaled 0.66 for 20 mm side. I used a brim.
P
Printables
Braille teaching aid
-Learning aid for people without or with low vision. I believe it will be useful to someone :) -If you print out more sets of letters you can start making words and sentences -The cubes are 2x3cm in size and the thickness is 3mm including…
P
Printables
saddle rail gopro mount
Testing. Gopro mount for saddle rail. 7mm round and 7x9mm oval rail. I modeled this to mount CO2 cartridge under the saddle. 1x M3 OD5mm heat insert 1x M3 bolt 10~12mm 1x M5 bolt 16~18mm 1x M5 nut
P
Printables
Corsair SPEC-04 Hard Drive Rail Replacement
A simple print to replace a missing hard drive caddy for the Corsair SPEC-04. There is only one file, so mirror this in your slicer to have both sides. Prints easily on the narrow edge without a brim, although I recommend it if you are…
P
Printables
Drawer Rail End Cap Schubladenauszug Endstopp
The old plastic broke away and the drawer always fell out. So here ist the new end Cap for the Drawer rail. The wheel has a Diameter of 20mm.
P
Printables
Curtain rail support bracket (Double C-Type)
Best printed with standard support, but also possible without supports, brim recommended to avoid warping.
P
Printables
diffusor for Prusa LED-Light Rail
diffusor for the printed Prusa LED-Light Rail from Lord_Syrus: https://www.printables.com/model/132588-u-channel-for-sethbons-led-prusa-light-bar print in white PLA and attach with glue
P
Printables
1010 Rail Guide for Model Rockets (v4)
These are designed for larger model rockets (≥ 3-in body tube) to fit on a 1010 aluminum extrusion ("rail") with just enough wiggle room to prevent binding but will slide nicely and keep the pointy end going up. They have 6mm holes so a…
P
Printables
3D Printer Camera Rail-Mount - Logitech C525 & others
This camera rail-mount / holder allows you to change the height and Z-axis rotation of your camera. Using the joint on the camera you can also change its pitch. The rail can be mounted vertically on the leg/side of the enclosure. You can…
P
Printables
trailer hitch for toy car (replacement)
The trailer hatch of a toy car broke - so I had to design a small replacement part. Thankfully the original part was mounted with just one single screw.
P
Printables
1/4in Socket Rail Adapter
Just added a positive bump to lock the socket better, this will hold best when on the rail.
P
Printables
Storehouse Bin Rail adapter
This piece adapts a harbor freight storehouse bin to a Vevor 14" ball bearing drawer slide to make a Sortimo-esque rack.
P
Printables
Plastové svodidlo / Plastic guardrail 1:14
Model dočasného silničního svodidla. Stohovatelné, lze pokládat pomocí paletizačních vidlí. Lze tisknout v běžné poloze i “vzhůru nohama”. Spojka se nasune na jednu stranu rohového dílu - podle potřebného směru zatočení. Davidův článek o…
P
Printables
1mm Spacer/shim to raise MGN12 Linear rail
I needed to lift up my linear rail slightly to use the NeedItMakeIt Y-axis Linear rails, so I designed this. It would be suitable for anyone who ever needs a shim for a MGN12 linear rail, for any purpose
P
Printables
Pimoroni Automation Hat Mini Case for Pi Zero - DIN Rail
Just added a DIN Rail mount to the middle part for industrial mounting also made some printability improvements Category: Electronics
P
Printables
Rail in 1:35 scale
Modular rail for 1:35 scale modelling. Gap Gap 1:1 Height Height 1:1 Width Width 1:1 Russian 43mm 1520mm 5mm 176mm 2mm 70mm European 41mm 1435mm 5mm 176mm 2mm 70mm Both European and Russian models has female and male ends so you don't…
P
Printables
Straight Rails fir Gravitrax - Normal version
Here are four straight rails that can be used with Gravitrax, each spanning 1 to 4 tiles. The length is approximately equivalent to that of the original Gravitrax rails. Note : I'll be uploading separately some rails that are 1 to 3 mm…
P
Printables
ETAP 22/23 (i/il) scepter cap / railing top adapter
Railing support 25 mm top adapter. Print in ASA for UV resistance. Sand and smoothen the top with acetone, if needed. Use 5+ walls for strength. For a clean top, print as is, with supports. Print outer walls first (or vv) to reduce outer…
P
Printables
Thingrail
This model was created to maximize workbench space be creating a place for your tools when they are not being used. The holes on the back allow the model to be mounted to a wall via screws. and I added some bins to make a place for all…
P
Printables
Linear Rail Guide Adapter For Quick Swap Kit - Snapmaker 2.0 A350
I was looking for a solution to use the linear rails SBR16 with the quick swap kit and it was also necessary that we can quickly remove the adapters.
P
Printables
Walther SSP / SSP-E Picatinny rail
Additional Hardware you need for this Print: 2x M5 threaded Inserts 2x M5 set screws (optional with a Polymer tip) I recommend the print orientation as seen on the Pictures. In this vertikal stand no support shut be needed. Depending on…
P
Printables
B&N Box Car for Dragon Railway - AMS Livery
This is rambros ' excellent box car model for Dragon Railway , remixed with a Burlington and Northern livery to print on a Bambu AMS. The assembly instructions can be found on the original model page:…
P
Printables
HK VP9 Rail Holster
Holster for an HK VP9 using the rail, which enables easy holstering (and removal) when large attachments are on the rail. The mounting holes are 32mm apart, and fit common Safariland and other belt attachments. There are several hole…
P
Printables
Square for guide rail Makita/Festool
Both models are printed without supports. The models are connected with an M4 screw and nut.
P
Printables
Reddot Lens-Protector / Killflash for Short Picatinny Rails (2 Versions available)
Because my Picatinny rail was too short and the standard off-the-shelf Lens-Protectors did not fit, I designed this shorter version. (mounted on a Tavor T21) The lens is taken over from the normal lens protectors that can bought e.g. on…
P
Printables
Hook Lock for IKEA Hultarp Kitchen Organizing Rail
I got annoyed by that the hooks of the IKEA Hultarp kitchen organizing rail (see Ikea Screenshot) all the time fell out of the rail when taking off some things for cooking. Therefore I printed these little locking parts. They lock into…
P
Printables
Mount for Reese Brakeman Trailer Brake Controller
Want to add a Reese Brakeman Brake Controller to your Toyota Tundra or Toyota Sequoia without drilling any holes? This mount just slips the brake controller on to the lower knee bolster of the dashboard and can slid off when not in use!…
P
Printables
Iron sights for nerf blasters with picatinny rails
These are available in 1, 1.5 and 2 degree pitch options. i recommend trying 2 degrees for 70-100fps, 1.5 degrees for 100-150, 1 degree for anything above that. a 30mm raiser is included for blasters with a very flat top like the nexus…
P
Printables
Rail up and down (wooden rails)
I print lying down with supports. The track doesn't need to be supported, but the fibres may come loose.
P
Printables
glass/plexi (2-3mm) door double trail
!!! This model is still in progress - I am adding new models/info !!! ------------------------------------------------------------------------------------- Background/What is it? In my leasure I like building simple cabinets, wardrobes,…
P
Printables
Travel Trailer Ethernet Pass-Through
This is designed to replace the coaxial input/output ports commonly found on travel trailers and RVs, allowing you to repurpose those ports for Ethernet connections without modifying or adding new holes to the trailer. The design is…
P
Printables
Brio train rail storage pillar
This can be used to store the rail segments of the brio train in a neat way. It can store a stack of rail segments on both sides. There are STLs for several stack heights. I found the idea from this model for duplo rails , which also…
P
Printables
1/10 scale offroad utility trailer
This is just a simple 1/10 scale off-road utility trailer. It has a trailing arm suspension, and is tested to be trail/off-road ready, and is sized around 1.9 1/10 crawler wheels. Print the frame and suspension components in PETG at least…
P
Printables
25mm Clothing Rail Mount
Perfect Holder for a 25mm Clothing Rail I designed a holder specifically for a 25mm clothing rail, and it works perfectly. Here are the details: Design Features The hook is slightly smaller than the rail's diameter, allowing the rail to…
P
Printables
Functional Model of a European style railway screw coupler (UIC Schraubenkupplung)
update: I just found an existing model in Scale I and II - obviously I previously did not find the proper search words. Still, that model is not functional (no threads) - see my " railway stuff " collection. I don't think a thread for…
P
Printables
Pulse XE Y-Axis Linear Rail Guide Upgrade
Pulse XE Y-Axis Linear Rail Guide Upgrade The MatterHackers Pulse XE is a MK3S+ clone, however not an exact copy, some parts or combination of parts are of different size and manufacture. Based mostly on version 2 of KalleKnall's Prusa…
P
Printables
Daedalus 2024 Update Project (RailCore II)
Video Series Link: This is my entire Daedalus Upgrade project that I've been working on for the past 4-5 months. I've uploaded all of my files here for you to embark on this journey if you'd like or take parts of my build and make it into…
P
Printables
TRX4m Trailer spare tire mount/rear bumper.
Made for two spare tires. just pops into the holes. Easy to print. ENJOY! MRC.
P
Printables
JST-XH mounts for 2020 rail
A simple printed mount for three 2-pin, or three 3-pin, JST-XH connectors. I used one to keep the fan wiring under my Voron Trident bed tidy. Then I could run a single fan power cable up from the electronics bay, and have connectors for…
P
Printables
1/18th trailer.
Easy to print and put together. PLS DOWNLOAD and LIKE! THANK YOU FOR SUPPORTING ME IN MY ADVENTURE OF 3D MODELING! MRC.
P
Printables
Kato Unitrack Rail Clips
KATO Unitrack Rail Clips. To secure the rails to the building plate without glueing the rails themselves Printing I printed with PLA, 0.2 mm layer height. Assembly Slide the clips under the rails. Use glue under the clip or screw the…
P
Printables
You have died of dysentery. (The Oregon Trail)
You have died of dysentery. (whoops) Print Settings Printer Brand: Artillery Printer: Artillery Sidewinder X1 **Rafts:** No Supports: No **Infill:** 100%
P
Printables
Zigbee GIRIER Modul DIN Rail
Da ich im Verteiler Platz sparen wollte habe ich eine Halterung gezeichnet die es ermöglicht ein GIRIER Modul senkrecht zu montieren. Da die Eingänge über 5 Drähte herausgeführt werden ist die Aussparung dafür vorhanden und kann mit dem…
P
Printables
Curtain Rail Clip
A clip for Curtain rail, snap into place and slideable. I've found the orignal clips snapping, and replacement parts seem way to expensive. I've redrawn the orignal ones and made some changes. Printed in PETG. Best way to print is…
P
Printables
Low profile NV rail for PGM Hecate sniper rifle
Low profile NV rail for PGM Hecate sniper rifle
P
Printables
Airline rail end cap / Airlineschiene Endkappe
Airline rail end cap. Perfect for: https://ntg-online.de/shop/Airlineschiene-Zurrschiene-2-x-2-m-2-Meter-halbrund-m-Bohrungen-u-Fitting-Plastik Tight fit. Will not come off easily. Print with supports on build plate only. Deutsch:…
P
Printables
Z bracket mount for z rails system
print as shown in the picture, use of Trees (Organic) with support to bed only works best
P
Printables
Linear Rail Carriage Remix for the SWX2
This is a remix of the linear rail carriage for the X1 to X2. For more info refer to https://www.thingiverse.com/thing:4597994/files Thanks patsp and uspaeker for the original work.
P
Printables
E3NG Dragonburner mount (Phucaf rail mod) - extended
The lower section of the original doesnt allow for Klickly/KlickyNG bases to fit behind a mounted Dragonburner. I've extended that section to give more space whilst not going too far back so its still shorter at the bottom than the 20x20…
P
Printables
Raspberry Pi Zero DIN RAIL Mount Bracket - Staffa installazione Pi Zero su barra DIN
Raspberry Pi Zero DIN RAIL Mount Bracket - Staffa installazione Pi Zero su barra DIN 7.5mm Suitable for: DIN RAIL 7.5mm IEC/EN 60715 TH 35 - 7,5 https://www.printables.com/model/885933-desktop-din-rail-stand-7590-degrees-supporto-barra…
P
Printables
Swoopy AFG for Short Rails
A remix of @shoelesshistorian's updated Swoopy Picatinny AFG, with closer bolt spacing so that it works with rails with only 3 or 4 grooves. Specifically based on the stubby/small version of the original.
P
Printables
Hot Metal / Bottle / Torpedo Rail Car
Scale parts to 2.63% for 1:87/HO/OO/1.65mm gauge Includes optional/removable cover for turning gear & motor [edit April '26 - added a split ladle for upright printing]
P
Printables
5015 Rapido UHF BL Touch Mount - Ender 3 Lightweight DD Overhaul & Linear Rail
A modified left mount that fits the BLTouch/probe on the inside of the mount. This reduces the distance from the nozzle, decreasing the x/y runoff needed to probe the whole bed. x_offset: -20 y_offset: -17
P
Printables
HGX Light - Ender 3 Lightweight DD Overhaul & Linear Rail
Adjusted X Carriage to work with Rapido UHF and the HGX Lite V2 Extruder mounting holes.
P
Printables
Campagnolo front derailleur setting tool for 50 and 52+53 teeth front chainring
In order to assembly and fit position of front derailleur you can use this tool.
P
Printables
Wagon for Oregon Trail card game
I created this little basic wagon for the Oregon Trail card game. You can place the wagon on the card in play and move the wagon to Oregon. Print Settings Printer Brand: Creality Printer: Ender 3 **Rafts:** Doesn't Matter Supports: Yes…
P
Printables
Trailer lift
Hello. Here is a trailer lift for TRX-4M as already been seen and done, this one however is a bit more heavy-duty shaped around axis. First version is regular, for use with standard trailer wheel and screw. You need to provide another set…