1 / 8
Voron 2.4 CW2 Cover for Nitehawk-SB — Noctua & Wathai/Sunon 4010 — image 1
1 / 8

Voron 2.4 CW2 Cover for Nitehawk-SB — Noctua & Wathai/Sunon 4010

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Clockwork 2 cover for Nitehawk-SB with a 4010 fan: Sunon, Wathai or Noctua, PWM or always-on.

Rating
0 / 5
Likes
2
Downloads
18
Makes
0
Views
260
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution

A Clockwork 2 cover for the Voron Stealthburner with a LDO Nitehawk-SB toolhead board and a ChaoticLab Tap V2. It adds a 4010 fan that blows on the toolhead board, which needs active cooling in a hot chamber.

Remix of Clockwork 2 LDO Nitehawk-SB Cover with 4010 Fan Mount. Big thanks to the original creator.

Why: with a well-sealed enclosure my chamber reached 55–57 °C, and at that point passive cooling wasn't enough for the Nitehawk. Without a fan you can get throttling, communication errors or disconnects on long prints. With the fan, the Nitehawk stayed around 62 °C with the chamber at 53 °C.

I used this cover until I switched to a Galileo 2 extruder. The recommended setup below is the last one I ran.

Recommended setup

  • Cover: Rev2

  • Fan: Sunon 4010

  • Control: PWM from a spare fan port on the mainboard, so Klipper runs the fan at 60% and boosts it when the board gets hot.

Which fan

Fan

Noise

Z belt clearance

Cover file

Sunon 4010 (recommended)

Loud at full speed, fine at 60% with PWM

Clears the belt, even at X-max / Y-min

Rev2

Wathai 4010

Louder (runs at full speed without PWM)

Clears the belt

Rev2

Noctua NF-A4x10 24V

Quietest

Thick enough to touch the Z belt of the front-right motor, and the fan guard makes it worse

Rev2 or Rev1, plus the swirl guard

If you can solder, swapping fans takes 10–20 minutes, so you can try one and switch later.

Mounting the Sunon

The Sunon's holes are made for M4. Countersink them slightly and use M3 flat head screws: the heads sit below the fan surface and keep the stack as thin as possible, so nothing touches the Z belt. Trim the screws if they stick out past the plastic on the back.

PWM wiring

  • The fan + wire stays on the Nitehawk 24 V, as before.

  • Disconnect the fan − wire from the Nitehawk GND and run a single 26–28 AWG silicone wire along the umbilical to a spare fan port on your mainboard (for example Leviathan V1.3 FAN1, pin PB3). Most boards switch the fan on the ground side, so only the − wire needs to go to the mainboard.

  • With my Spine Umbilical System, the extra wire clips along the umbilical with the Spine Link Clips, no zip ties.

Klipper config

CW2_Cover_Rev3_PWM_Fan_Setup.txt has everything to paste in:

  • a fan_generic section for the fan (change the pin to yours);

  • an automatic monitor: 60% normally, 100% when the Nitehawk reaches 65 °C, back to 60% below 60 °C;

  • auto-start at boot, and the lines to add to PRINT_START, END_PRINT and CANCEL_PRINT.

It reads the Nitehawk's own temperature sensor, which should already be in your config. If you hear a whine at partial speed, the file shows a higher PWM frequency to try.

Simple option: always on

If you don't want PWM, connect the fan straight to the 24 V lines that feed the Tap V2 (red +, black −). For the Noctua that's yellow (+) and black (−); the green (RPM) and blue (PWM) wires aren't used. Mount the cover first to measure how long the wires need to be, insulate the splices with heat-shrink or Kapton tape, and route the wires through the cover's side channel, away from the toolhead board.

Files

File

What it is

CW2_Nitehawk_Cover_Noctua_Wanthai_Sunon_Rev2

The cover. Use this one.

Noctua_4010_Swirl_Fan_Guard

Fan guard, only for the Noctua.

Spine_Link_Clip

Clips the extra PWM wire along the umbilical, if you use my Spine Umbilical System.

CW2_Cover_Rev3_PWM_Fan_Setup.txt

Klipper config and macros for PWM control and automatic temperature boost.

CW2_Nitehawk_Noctua_Cover_Rev1

Old version, Noctua only. Kept for reference.

Printing

  • Material: ASA or ABS, for the heat in the chamber.

  • Noctua only: 4 × M3×16 flat head screws hold the fan and the swirl guard.

Changelog

  • Rev3: PWM fan control from the mainboard, Sunon 4010 recommended.

  • 2026-03-13: Rev2, works with the Wathai and Sunon. Note about the Noctua touching the Z belt.

  • Rev1: first version, Noctua only, always on.


About this description: I design, print and test everything myself. I'm a hands-on maker, not a writer, so I use AI (Claude, by Anthropic) to help me organize and polish the text.

Tags