38mm to 29mm Rocket Motor Adapter (with Thermal Offset)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Versatile adapter to allow for more rocket motor types
- Rating
- 0 / 5
- Likes
- 5
- Downloads
- 35
- Makes
- 0
- Views
- 113
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- RC & Robotics
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Introduction
This is a refined version of my 38-to-29mm motor adapter, updated for better durability and fit. It allows you to fly 29mm motors in any rocket equipped with a 38mm Motor Mount Tube (MMT) without paying the "rocketry tax" for commercial hardware.
Please read this entire document before printing. I’ve tried to make it more entertaining than a flight manual, but the technical bits actually matter if you want to keep your rocket in one piece.
Key Design Features
Thermal Protection: The inner diameter is slightly oversized to accommodate a 29mm motor tube as an insulator. This keeps the plastic from reaching its "forbidden marshmallow" state (glass transition temperature) during flight.
Going "Commando": While designed for an insulator, it can be flown as a "one-and-done" part without one. Perfect for when you're at the range and realize you forgot your "real" hardware.
Aerotech Compatibility: The thrust ring is sized proportionally to an Aerotech 38mm motor, ensuring standard retainers can easily encapsulate the assembly without a fight.
Estes Compatibility: Works with Estes BP motors, but you’ll need a thrust ring. Use the "tape wrap" method or grab my 29mm Thrust Rings (coming soon).
Integrated Stops: Features internal stops to ensure your motor sits flush and secure, rather than trying to exit through the nose cone.
Printing Recommendations
The "Pro" Choice (ASA/ABS): Best for superior heat resistance. If you're flying high-impulse motors, this is the way.
The "Daily Driver" (PETG): Highly effective when used with the internal insulator.
The "Yolo" Choice (PLA): Acceptable only if the 29mm insulator tube is installed. Otherwise, expect a very artistic, melted souvenir after one flight.
Supports: Minimal supports required for the upper centering ring. If your printer is well-calibrated, you might be able to print this support-free.
Assembly Instructions
The Insulator: Cut a section of 29mm motor tube to approx. 110mm (4-1/4 inches).
The Goo: Apply a very thin coat of epoxy to the inside of the adapter and slide the tube in.
The Cleanup: Wipe off the squeeze-out (there is always squeeze-out) from the bottom with Isopropyl alcohol.
The Inspection: Check the inside of the tube for stray epoxy. If you skip this, your motor will fit, and you’ll get to start over from Step 1.
The Wait: Let it cure. Do not rush this. Gravity and chemistry do not care about your launch window.
The Result: Launch, celebrate, and hopefully recover!
Frequently Asked Questions
1. Do I really need to use an internal insulator tube? It’s the difference between a reusable tool and a disposable one. Without it, the motor burn will likely deform the plastic. Also, some single-use motors have labels that are a pain to slide into tight tubes. Going "commando" (no insulator) means you don’t have to waste time peeling stickers, but you’ll be printing a new adapter for the next flight.
2. Which material is actually the best? ASA/ABS. PETG is fine, but if you use PLA without an insulator, your adapter will have the structural integrity of a warm gummy bear by the time the ejection charge fires.
3. Will this work with my retainer? If it fits a standard 38mm Aerotech motor, it fits this. It’s designed to be a "drop-in" replacement for commercial hardware.
4. How do I reach you? If you have questions about printer settings, insulator sourcing, or "Is this motor going to melt my face off?"—please ask! I’m happy to assist. I’d much rather help you over-engineer your build than see a CATO at the range.
The "Rapid Unscheduled Disassembly" Warranty
Because let’s face it: you are essentially stuffing a controlled explosion into a plastic tube and pointing it at the clouds.
The "As-Is" Clause: I warrant that this file exists and looked great on my screen. Once you hit "Print," you are the Chief Engineer. If your printer produces plastic spaghetti, that’s between you and your slicer.
The Thermal Reality Check: If you print this in PLA and it melts into your rocket’s soul, that’s on you. Physics is a harsh mistress and she doesn't issue refunds.
The "Yeet" Disclaimer: Once the motor ignites, all bets are off. If your rocket performs a "gravity-assisted rapid reconfiguration" (crashes), I cannot be held liable for the heartbreak or the walk of shame into the woods. I feel your pain—I’ve walked that lonely road—but I can’t pay for your new airframe.
The Safety Police Section: Rocketry is a safe and rewarding hobby, but these are not toys. You are responsible for the rockets you fly. Understand the NAR/TRA Safety Code. My parts are for experienced rocketeers who understand the risks. By using this design, you assume all liability. Join a club, ask questions, and get that flight insurance!