1 / 3
Sovol SV08 Max Door Spacer Set - 2mm Foam Seal Compensation — image 1
1 / 3

Sovol SV08 Max Door Spacer Set - 2mm Foam Seal Compensation

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Custom-designed spacer set for the Sovol SV08 Max to accommodate 2mm foam sealing tape.

Rating
0 / 5
Likes
8
Downloads
18
Makes
0
Views
124
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution

Summary

Custom-designed spacer set for the Sovol SV08 Max to accommodate 2mm foam sealing tape installed between the chamber door and frame. This modification significantly improves heat retention by properly sealing the chamber while maintaining correct door alignment and operation.

Description

When adding foam sealing tape to your SV08 Max chamber door for better heat retention, the additional 2mm thickness creates a gap that prevents the door from closing flush and latching properly. This three-piece spacer set solves that problem by offsetting the door mounting points and hinges by precisely 2mm.

What's Included:

  • Top Door Spacer - Dual-cylinder design that mounts at the top of the door frame

  • Bottom Door Spacer - Matching spacer for the bottom door mounting point

  • Hinge Spacer Plate - Flat spacer with dual mounting holes for door hinge adjustment

Why You Need This:

If you're running high-temperature materials like ABS, ASA, PC, or Nylon, maintaining consistent chamber temperatures is crucial for print quality and reducing warping. Adding foam sealing tape dramatically improves heat retention, but without proper spacers, your door won't close correctly. This set ensures:

✓ Perfect door alignment after adding foam tape
✓ Proper latch engagement
✓ No gaps or light leaks
✓ Smooth door operation
✓ Maximum chamber heat retention

Design Features:

  • Precisely dimensioned for 2mm foam tape compensation

  • Uses factory screw locations

  • Matching cylindrical profiles on top/bottom spacers for clean installation

  • Integrated mounting geometry matches factory door mounting points

  • Hinge spacer designed to work with stock SV08 Max hinge hardware

  • Minimal material usage while maintaining structural integrity

Print Settings

Printer: Any FDM printer (designed and tested on Sovol SV08 Max)

Material:

  • Recommended: ASA, ABS, or PC (heat-resistant for chamber environment)

  • Alternative: PETG (acceptable but less ideal for high-temp chambers)

  • Not Recommended: PLA (will deform in heated chamber)

Layer Height: 0.2mm - 0.3mm

Infill: 30-50% (these are structural parts that need good strength)

Perimeters: 3-4 walls minimum

Support: None required - parts are designed to print support-free. If top piece is laid on its back support will be required .

Orientation:

  • Top/Bottom Spacers: Print with flat base down

  • Hinge Spacer: Print flat on bed

Assembly Instructions

Required Hardware:

  • 2mm foam sealing tape - Tape

  • Magnets - Magnet

  • Original door mounting screws (reuse from printer)

  • Phillips screwdriver

Installation Steps: "Door can be left on and install hinge spacers one at a time."

  1. Remove Chamber Door

    • Open the chamber door fully

    • Remove screws from top and bottom mounting points

    • Carefully lift door off hinges

  2. Install Foam Tape

    • Clean door frame contact surface with isopropyl alcohol

    • Apply 2mm foam tape around the entire door frame perimeter

    • Ensure tape is continuous with no gaps at corners

  3. Install Door Spacers

    • Position Bottom Door Spacer at the lower mounting point

    • Insert original screw through spacer into frame

    • Repeat for Top Door Spacer at upper mounting point

    • Hand-tighten both screws (don't fully tighten yet)

  4. Install Hinge Spacers

    • Remove hinge mounting screws

    • Place Hinge Spacer Plate between hinge and door

    • Align holes and reinstall screws

    • Repeat for second hinge point

  5. Reinstall Door

    • Hang door back onto hinges

    • Test door swing and latch engagement

    • Adjust spacer positions if needed for perfect alignment

    • Fully tighten all screws once alignment is confirmed

  6. Final Testing

    • Open and close door several times to verify smooth operation

    • Check that latch engages properly

    • Inspect foam compression - should compress evenly all around

    • Look for light leaks with chamber light on in dark room

Post-Printing Notes

Quality Check:

  • Inspect parts for warping or de-lamination before installation

  • Verify hole alignment matches your printer's mounting points

  • Test-fit spacers before installing foam tape (easier to troubleshoot)

Maintenance:

  • Foam tape may compress over time - check seal periodically

  • If using PETG spacers, monitor for deformation in heated chamber

  • Can be reprinted in higher-temp material later if needed

Troubleshooting:

  • Door won't latch: Spacers may not be fully seated or screws over-tightened

  • Uneven gap: Check foam tape application for consistent thickness

  • Door binds: Verify hinge spacers are properly aligned

  • Light leaks at corners: May need additional foam tape at corner transitions

Material Recommendations:

For best results in a heated chamber environment:

  1. ASA (Best Choice)

    • Excellent heat resistance (glass transition ~100°C)

    • UV resistant

    • Maintains dimensional stability in chamber heat

    • Easy to print on SV08 Max

  2. ABS

    • Good heat resistance (~105°C glass transition)

    • Widely available

    • Strong and durable

    • May have slight odor during printing

  3. Polycarbonate

    • Highest heat resistance (~150°C glass transition)

    • Extremely strong

    • More challenging to print

    • Overkill for this application but works great

  4. PETG (Acceptable)

    • Lower heat resistance (~80°C glass transition)

    • Fine for chambers kept below 60°C

    • Will soften if running extended high-temp prints

Avoid: PLA, TPU, or other low-temp materials

Tags