1 / 2
Case for Mr Bear Family travel size beard brush — image 1
1 / 2

Case for Mr Bear Family travel size beard brush

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This case is to protect your beard brush on your travels, when the case accompanied with the brush won't do.

Rating
0 / 5
Likes
0
Downloads
2
Makes
0
Views
16
Reviews
0

Updated at source:

Model information

Category
Bathroom
License
Creative Commons — Attribution — Share Alike

This case is to protect your Mr Bear Family travel beard brush. The case has soft contours, following the brush contours, to keep the handling of the case as satisfying as handling the brush.

The brush had come in a nice looking cardboard box, but after some time and use, it started slowly but surely to disintegrate. This called for ratification! I needed to protect the brush, which cares for my beard!

Design choices and reflections

Print environment

I printed the case without supports, with their flat sides against the build plate.
Print environment: Prusa Mini+ with input shaper enabled, Prusa textured heatbed steel sheet, 0.25mm brass nozzle, 0.15mm layer height with OrcaSlicer's Speed settings (altered first layer print speed to 20 mm/s due to first layer not sticking), white SUNLU High Speed PLA+ filament. I may not have dialed my printer properly with this filament yet. See the "body top edge" section for reason.

Case internal size

Initially, I had put the case internal size to have a 0.5mm bigger radius than the elliptic sketch I made of the brush. This, however, was slightly too small, as the brush handle had not an identical shape. It was slightly flattened on the ends, probably to make it nicer to hold in the hand. I didn't want to forcefully push my brush into the case, so I increased the radius to be 1mm bigger instead. This caused the brush to be only slightly loose in the case. If you want to, you can try changing the BoxInline constraints to increase the radius with only 0.75mm. The other constraints should update and reflect the changes.
The internal height is set to 30mm, and there is almost no rattle. The bristles do not seem to be in almost any stress and do not look bent at all when looking through the case hole.

Push hole

Both parts of the case were given a push hole to ease getting the brush out of the case. Another feature of the hole is to allow the brush to dry, if it was used on wet beard. If you don't want to have the brush side, or neither side, open, you can block the hole in the slicer with a 2mm thick slab/box. The push hole its form and size to also allow viewing of the whole label on the handle.
As you can see from the pictures, my brush had a not fully centered label, but I find mine to be good enough with this size of a hole. If you do not agree, you can resize the BoxPushHole sketch.

Body top edge

The top layer of the body became so thin, it only got one pass of filament and the final layer did not end up that good, so I ended up cutting and ripping most of the last layer off. You may get better results using normal speeds, which you can achieve without enabling input shaper.
I am satisfied with the results, but if slowing the printing down does not help, I may update the body with a broader top edge, as described in the "box alignment edges" section.

Box alignment edges

I had made the body alignment edge have a 0.1mm bigger radius than the edge of the lid. This is to ensure that the parts fit together, even though there is a slight radius shrinkage and the print seams affect the fitting. The 0.1mm radius increase was not taken into account when setting the body alignment edge chamfer. Woops!

The lid and body alignment edges have a chamfer on the inside to make inserting the brush nicer. The height of the body alignment edge chamfer is affected by the height of the edge height.

FreeCAD project structure

The FreeCAD project file is parametric, with the the sketches of the body part referencing directly their counterparts on the lid part. The constraints used are those of an ellipse, length and width. The height of the case is made using the pad feature.
The reference tree is as follows:
- BrushContours is referenced by
 - BoxInline
- BoxInline is referenced by
 - BoxOutline
 - BoxAligner
- Box<X> is referenced by
 - Box<X>001
- Pad002 (of BoxLid) is referenced by
 - Pocket005 (of BoxBody)
- Pocket005 is referenced by
 - Chamfer001

Tags