SuperGrip Bowden Tube Clip / Retainer + M10 Threaded Fitting — Universal PTFE Tube Lock for Filament Dryers, Enclosures & Passthroughs
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Locks your Bowden tube in place so it doesn't get pushed into the dryer. Strong grip, no glue. M10 threaded version incl
- Rating
- 5 / 5
- Likes
- 70
- Downloads
- 162
- Makes
- 5
- Views
- 1,500
- Reviews
- 5
Updated at source:
Model information
- Source
- Printables
- Category
- Accessories
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
note 11th April - Significant improvemtne to grippiness! I accidentally had an older version of the legs - if you downloaded it, get the new version here.
📌 TL;DR: Your Bowden tube gets slowly pushed into the dryer during printing. This retainer locks it in place with an exceptionally strong grip — no glue, no tape. Includes a built-in mechanism to access the coupler release button for maintenance. Also comes in M10 threaded versions for DIY passthroughs. 4 variants + compression sleeve included, print the one that fits your setup.
The Problem
The Bowden tube slowly gets pulled INTO the dryer during printing. The S4's couplers are one-way — you can push the tube in freely, but pulling it out requires pressing the release button. Every time the extruder pulls filament, spool friction drags the tube deeper inside — millimeter by millimeter. You can see in the GIF that even with very little filament resistance, the tube gets pulled right in. Eventually the tube kinks, filament wraps around the spool, tension builds on the printer, and your print fails.
Before this, I had electrical tape wrapped around the tube to try to hold it in place. It barely gripped, and every time I loaded new filament it shifted and needed readjusting. You can see the mess in the photos — not exactly a real solution.
Even with minimal resistance, the tube slides right in
The Solution
This retainer slides onto your Bowden tube and acts as a physical stop — the outer diameter is too wide to pass through the coupler, so the tube simply can't be pushed in anymore. No permanent modifications to your dryer.
The gimmick - The X4's coupler (release button) is recessed and hard to reach, especially on the back. So the main version includes a built-in sliding pusher — the inner part telescopes through the outer body, letting you press the release button without removing anything. Need to pull the tube out for maintenance? Push the inner cylinder down and pull. No tools needed.
The sliding pusher mechanism in action
💪 Designed to grip — not slip. PTFE tubes are notoriously slippery and most clamp designs slide right off. After 40+ iterations of trial and error, I found a bore geometry that actually holds. Once installed, I couldn't get the tube to slide through even pulling hard. No glue, no tape — just friction done right.
What's Included
Retainer_PushFit_with_Release.stl— Push-fit retainer with built-in sliding release pusher (requires supports)Retainer_PushFit_with_Release_NoSupport.stl— Same as above, redesigned to print without supportsFitting_Threaded_M10.stl— M10 threaded fitting — passthrough OR tube lock. Screw into any panel, pass the tube through, it stays put.Retainer_Simple_Open.stl— Simple retainer with open access to coupler button — no moving parts, no thread, simplest printCompression_Sleeve.stl— The ring that slides over to grip the Bowden tube
How It Works
Slide the retainer onto your Bowden tube — the inner bore grips the 4mm OD PTFE tube with a snug friction fit.
Push the tube into the coupler as usual — it stops when the retainer's wider diameter hits the coupler.
Print away — the extruder pulls filament freely, but the tube stays locked in position.
Need to remove the tube? Push the inner cylinder down to press the coupler release button, then pull the tube out.
Print Settings
Material: PETG recommended (heat resistance + layer adhesion). PLA works but may warp at higher drying temps.
Layer height: 0.20mm
Perimeters: 5 (small part, essentially 100% infill this way but stronger)
Supports: None needed
Orientation: Standing up (as oriented in the STL)
If yours prints and the fit isn't good or too tight, increade or decrease the sleeve by a percent or two.
Designed with chanfers in all the right places for no support printing except the shorter one with two parts - the supports are already painted on in the 3mf file for that one.
🧹 Post-print: Small overhang inside the smaller push-fit version. Poke something through to clear it, or just push the tube through firmly on first insertion.
Compatibility
Designed for: Sunlu FilaDryer S4 Also works with any dryer using standard push-fit Bowden couplers:
Creality Space Pi / Dry Box 2.0 · Sovol SH01 / SH02 / SH03 · Eibos Easdry / Polyphemus · Any 4mm OD PTFE tube + PC4 fitting
Other Uses
Beyond dryers — anywhere you need a Bowden tube to stay put:
Reverse Bowden setups — tube from spool holder or dry box to extruder
DIY dry boxes — two retainers on either side of a wall as a passthrough
AMS / MMU tube runs — prevent shifting over time
Enclosure passthroughs — lock a tube in any hole
🔩 M10 threaded version included — screw into a drilled hole, works as passthrough + tube lock. Use with M10 nut to secure.
Why no M6? 4mm tube through M6 = less than 1mm wall. It'll crack. M10 gives 2.5mm+ wall, holds up fine.
The Story
I was printing TPU from my S4 and the tube kept getting sucked in. Looked online — tape, zip ties, super glue. None of that felt right. So I designed this.
Getting PTFE to stay put without glue was way harder than expected. Every early version slid right off. You can see all the failed attempts in the TinkerCAD screenshot — each one taught me something. Eventually I landed on a bore geometry that works, and here we are.
⭐ If this helped you, a boost or "makes" photo would mean a lot. Happy printing!
☕ Support & Other Projects
I spent a few nights on this silly gizmo getting it just right. If you want to throw a coffee my way, I'd really appreciate it! I hope this brings you some value and joy like it did me either way :D
☕ https://ko-fi.com/3dzoidberg
Also check out my Core One OctoPrint guide:
🐙 https://github.com/gilrstein1-ui/Octopi-CoreOne/