1 / 2
Moulds and Moulding Stand for F3/SFL Steering Wheel — image 1
1 / 2

Moulds and Moulding Stand for F3/SFL Steering Wheel

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Moulds and moulding stand for theSimbaSim F3/SFL Steering Wheel Project

Rating
0 / 5
Likes
2
Downloads
8
Makes
0
Views
202
Reviews
0

Updated at source:

Model information

Category
Computers
License
Creative Commons — Attribution — Noncommercial — Share Alike

Moulds and Moulding stand for the F3/SFL Steering Wheel Project

Create moulded polyurathane moulds with these models. This includes a moulding stand which you can mount your plate and moulds to while you cast them. You'll need to attach the stand to the wheel plate with a 2x M5 25mm bold and nuts.

Moulding Grips with Polyurathane Resin

I use the 'Polytek Poly PT Flex 60 Liquid Casting Rubber' which is available here: https://www.mbfg.co.uk/pt-flex-60-rubber.html - you will also need the black dye (which is available here: https://www.mbfg.co.uk/polytek_pigment.html). This has a pot life of around 4 mimutes, so make sure you have everything prepared before you mix up the rubber.

You will need:

  • Water washable resin

  • Cornflour

  • Sanding paper from 180 to 1000 (sanding sponges are ideal for this - https://alishort.com/CUJ6 )

  • Hot glue gun

  • Spring Clamps

  • 2x 500ml plastic measuring jugs for part A and Part B

  • 300my syringe

  • 2ml syringe for the dye

  • Weighing scales

  • Rubber mallet

  • Demoulding wedge or car trim removal tools

  • Silicone spatula for mixing

  • Scalpel

  • Side cutters

  • Kitchen Paper

  • Mould release silicone spray

How to Cast Rubber Grips tutorial

Prepare the Moulds

  • Print off with 4 walls, 15% infill

  • To fill in the layer lines, use a mix of water washable resin and cornflower (mixed 1:1, just paint it on and put on a window ledge to cure in the sunlight)

  • Sand up to about 400 grit

  • Apply high build primer and sand to around 1000

  • Sand the mating faces flat to about 1000

Prep for moulding with Polyurethane rubber

  • Spray with mould release silicone and allow to dry

  • Mount onto the plate and stand upside down (the moulds fill from the bottom) and ensure the front moulds are on the countersunk side of the plate

  • Use spring clamps to hold them moulds on, and make sure they are aligned correctly

  • Use a hot glue gun to seal the edges of the mould

Mixing and injecting rubber (for one grip)

  • Pour out 200g of mixing rubber (100g of part A in one container, 100g of part b in another container)

  • Add 2ml of black dye to part B and mix (check the instruction for whichever dye you buy - different colour require different ratios)

  • Add part A to part B and mix for no longer than 30 seconds. Mix at a steady pace, if you over mix the pot time will reduce

  • Draw the rubber into a 300ml size syringe

  • Wipe the nozzle of the syringe

  • Inject steadily into the mould

  • Allow it to set

  • Use demoulding wedges or car trim removal tools (you can 3D print these) and a rubber mallet to remove the moulds

  • Trim the flash off of the grips with a scalpel and side cutters

Tags