1 / 5
Abarth 595 / 695 Ph3 Led fog light pods — image 1
1 / 5

Abarth 595 / 695 Ph3 Led fog light pods

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is a 3d printed led pod holder with included magnetized caps designed to fit a 122mm led lamp

Rating
0 / 5
Likes
1
Downloads
5
Makes
0
Views
245
Reviews
0

Updated at source:

Model information

Category
Automotive
License
Creative Commons — Attribution — Noncommercial

Theses pods can be 3d printed in ASA with magnets enclaved for the 3d printed cover. They use a generic Chinese lamp that you can find on various seller. Let’s be honest, it’s not Tuningarts.uk carbon fiber pods with PIAA xenon lights, but that’s the DIY way !

Disclaimer : I used them for 1000km, so it’s probably still a prototype at the moment !

In use

When used, they act like a mix of everything : The light add a bit of power compared to the bi-xenon of my Turismo. The beam is very wide and I added a slight angle on the holder for the lamp to act like « rally » corner lights.  The cover will let the DRL light work. 
The final assembly of theses pods is supported by the bumper grill instead of using the oem fog light mounts. It can be a bit heavy for the grill so you need it to be well mounted on the bumper.

The lamp

This lamp can be bought with 4 DRL colors : White, Yellow, Blue and have 23119 as the product number. 
The color is close to oem xenon color : Probably around 4000k, it’s probably 90% pure white, but not 100% white like « Used » Xenon lamp. 
It’s marketed as a 216grams 72W IP68 12v/24v with a 120° radius flood wide spread beam for the DRL and 15° for the for the « Extreme distance ». 

Furniture

  1. You will need 2 metric screws + nuts to mount the lamps on the holder as the one included are a bit short to be mounted on my 3d printed holder.

  2. You will need 6 screw + bolts to hold tight the holder on the oem bumper.

  3. You will also need a pack of 24 magnets 5mm ø with a height of 2mm because each holder need 6 of them, each cover needs 6 of them, and you have 2 pods. 12 are not strong enough to hold the cover while running.

    Optionally :

  4. I heavily suggest 4 male and female Amp superseal 2 way connectors (6 to be safe cause they are sometimes difficult to use at first). 

  5. Some Add-a-fuse on the 12v accessory socket to have a +12v on the engine bay when you start the car.

Assembly

You will need to remove the front bumper. It’s not a big deal with theses 500. 4 screws on the top of the engine bay, 3 inside the middle of the bumper and some in the wheels are (3 if I remember well). You will need to pull hard on the bumper tabs that are made for the bumper to not vibrate. If you brake the tabs, don’t worry, you can buy them on a Fiat shop with the 2 big rivets. Take car of the headlight when doing that as you can scratch them. 

Then, you will need to remove the oem fog lights and cover. Save them because they cost ton of money. 
Assemble the holder by using the backplate and the 3 screw per pod. It’s made to be tight fit, so maybe trim a bit of plastic on the holder / backplate instead of forcing on your bumper. 

Wiring suggestion

For the fog light feature, I used the oem harness of the fog light. They are mounted by the factory with superseal 12v 2 wire sockets. The oem fuse and harness can power theses leds without issue on the dash. 

For the DRL, I used a add-a fuse on the harness of the engine bay to get 12v when ignition is on. On that, I added a wire into the fog light wiring harness so for the wire to be routed well.

Want to reward me ? 

As you can see I don’t do this for the money, but I would love to have a pretty 3dmodel for the DRL delete / grill replacement. If I can have a step to make my own design on top of it, it would be fantastic. 

Tags