1 / 9
Leslie S3L Inspired Train Horn, works with air! — image 1
1 / 9

Leslie S3L Inspired Train Horn, works with air!

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Leslie S3L, work in progress, I have only printed it half scale, yes, it actual works with air.

Rating
0 / 5
Likes
9
Downloads
53
Makes
0
Views
427
Reviews
0

Updated at source:

Model information

Category
Engineering
License
Creative Commons — Attribution — Noncommercial — Share Alike

Build Notes

This design started with a 1966 Leslie S-31 horn. The S-31 bell, back cap, power chamber, and single-bell manifold were drawn in Fusion 360 at full scale.

This is still a work in progress. The files may change as I continue testing and refining the design. I will post updates and revised parts as they become available.

I printed everything at 50% scale. The diaphragm material is clear plastic cut from a blister pack, approximately 0.4 mm thick.

Making the Diaphragms and Retaining Rings

Use the provided jigs to make the diaphragms and retaining rings.

Diaphragm

  1. Apply thin double-sided tape to the jig and stick the blister-pack plastic to it.

  2. Rough-cut the plastic with scissors.

  3. Finish the edge with 320-grit sandpaper, checking the fit as you go.

  4. Drill the holes with a 1/16-inch drill bit. A printable diaphragm template is included to help locate the holes.

Retaining Ring

  1. Clamp the retaining-ring material in the inner-hole jig.

  2. Cut the inside opening with an X-Acto knife.

  3. Finish the edge with 320-grit sandpaper.

  4. Use very small screws to secure the retaining ring. The screws must not interfere with the face of the back cap.

  5. Do not overtighten the screws. The retaining ring should remain flat and spin freely.

Diffuser

The diffuser can also be printed. Drill the offset hole with a 1/16-inch drill bit.

Use a countersunk screw so the fastener sits flat across the face of the diffuser.

Hardware and Assembly

When printed at 50% scale, the air-inlet holes in both manifolds will accept a 1/4-inch air fitting with a little persuasion. Added base adapter for 1/4 NPT fitting.

I used:

  • M4 × 16 mm bolts and M4 nylock nuts for the back caps, these should be snug

  • M4 × 40 mm bolts to attach each bell to its manifold and power chamber

  • #1-72 × 3/16-inch flat-head screw for the diffuser
    Walthers part number: 947-1062

  • 0-90 × 3/16-inch flat-head screws for the retaining ring
    Walthers part number: 947-1042

  • Fasteners should be snug, do not over tighten!

The hole in the power chamber will need to be drilled for the M4 bolt. I used a 9/64-inch drill bit. Added scaled power chamber with 4mm holes when using M4 bolts.

Do not drill deeper than 10 mm or you may break through into the chamber.

A #10 pan-head screw may also be used instead. Do not use a screw longer than 40 mm.

The three-chime manifold has removable plugs at each end so support material can be cleaned out of the internal air passages. The plugs are a friction fit, but they should also be secured with glue or sealant. Sealing surfaces should be sanded flat I added a thin coating of silicone to aid sealing.

Recommended Testing Procedure

Start by getting one horn working with the single-bell manifold before attempting the complete three-chime assembly.

Test each power chamber individually with a single bell. Once all three power chambers are working correctly, assemble the full horn using the three-chime manifold.

The diaphragm clearance is sensitive. Small changes can make the difference between a working horn and no sound at all. If you dont get any sound you can slowly tighten the bolts on the back cap until something happens, dont go too much. Compressor was set at 90psi, I used a blow gun with 1/4 NPT treads on the end to attach the horn with 1/4 NPT x 1/4 NPT male nipple.

Print Settings Used for the Tested Version

I printed the tested version on a Creality K2 Plus using PLA+.

  • Scale: 50%

  • Wall loops: 3

  • Infill: 15%

  • Layer height: 0.20 mm

  • Supports: enabled where needed

  • Base adapter printed with 4 wall loops and 50% infill

Print the power chamber and back cap with the diaphragm-contact surfaces facing upward so those surfaces have a clean finish.

Full-Scale Printing

All STL files are modeled at full scale and should be printed at 50% scale for the tested version shown here.

In theory, the parts could be printed at full scale and used with actual Leslie diaphragms. I have not tested this.

Accuracy Note

The #25 and #44 bells were modeled using rough measurements and reference images found online. The three-chime manifold was created the same way.

This is a Leslie S3L-inspired design, not an exact replica. Do not expect every dimension or detail to match an original S3L.

Safety Warning

This horn is loud. Very loud.

Test it outdoors and wear hearing protection.

Good Luck!

Tags