1 / 6
Upgrado Headphones: 50 mm Drivers for Grado — image 1
1 / 6

Upgrado Headphones: 50 mm Drivers for Grado

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Upgrade the drivers in your Grado headphones to 50 mm

Rating
0 / 5
Likes
0
Downloads
7
Makes
0
Views
74
Reviews
0

Updated at source:

Model information

Category
Audio
License
Creative Commons — Public Domain

Overview

I had a broken Grado SR80 from several years back that I wanted to get going again, but one of the drivers couldn't be recovered. Thus, I sought to swap in some new drivers.

Bill of Materials

Item

Qty

Part

Description

1

2

Headphone driver, 50 mm

50 mm diameter, 6.1 mm depth

2

2

M3 x 40 mm or longer, socket head cap screw (SHCS)

Secure yoke to rod block

3

4

M3 x 8 mm, socket head cap screw

Secure driver to yoke

Optional upgrades

4

2

Yaxi Comfort S Pads

Purple for extra fun

5

2

Flat Pads

Moves ear closer to driver, increasing bass and reducing highs

6

1

Turbulent Leather Headband

Add some cushioning for longer listening sessions

Tools

  • Soldering iron

  • 2 mm hex bit/wrench

  • 2.5 mm hex bit/wrench

  • Screwdriver

  • Multimeter

Instructions

  1. Order 50 mm x 6.1 mm drivers.

  2. Print parts.

    1. Enable supports on Inner Cup.

    2. Supports optional for Outer Cup.

  3. Disassemble original Grados.

    1. Soften glue.

      1. Careful use of a heat gun.

      2. Boiling water, about 1 cm high, on a plate.

  4. Desolder headphone cable from original Grado drivers.

  5. Insert the driver into Mount.

  6. Solder the headphone cable to your new driver.

    1. IMPORTANT: Ensure that you lace the headphone cable through the Inner Cup part before you solder the wire.

      1. Ensure the Inner Cup part is oriented correctly before lacing the headphone cable through. Arches should open toward the Y split, circular portion opens toward the driver and Mount.

    2. ALSO IMPORTANT: Use a multimeter to check for continuity between the 3.5 mm stereo TRS connector and wire ends.

      1. On my cable:

        1. Red is left (tip)

        2. White is right (ring)

        3. Blue is ground (sleeve)

    3. NOTE: keep track of which driver belongs to the left and right channels.

  7. Orient the Mount with respect to the Inner Cup so that the solder pads are at the bottom.

  8. Using a solid surface, press the Inner Cup over the Mount.

  9. Align the Grille with tab inside the Outer Cup, and insert.

  10. Align the tab on the inside of Outer Cup with the arch of the Inner Cup, and insert.

  11. Insert M3 x 40 mm or longer SHCS into top of headphone block, and screw into yoke.

    1. Ensure bolts point inwards toward head. Measured at about 7 degrees.

  12. Install pads.

  13. Just listen to your music!

Frequency Response Graphs

“I have studied audio design from the viewpoints of electronic design, psychoacoustics, and my own humble efforts at musical creativity. I have found complete scepticism towards Subjectivism to be the only tenable position. Nonetheless, if hitherto unsuspected dimensions of audio quality are ever shown to exist, then I look forward keenly to exploiting them.”

Douglas Self, Audio Power Amplifier Design

In audio, if you can hear it, it can be measured. If it can't be measured, it can't be heard.

Frequency response (FR) measures the loudness of a headphone driver at different frequencies. It requires specialized microphones, models of the human head, software, and expertise to properly measure the performance of audio equipment. Thus, whenever a person sets up this measurement rig, they tend to try to measure as many headphones as possible, sharing their results freely with the Internet, and we owe our gratitude to such fine folks.

Today, there are a healthy number of databases for headphone FR, but be aware that such graphs should ideally be compared against the same measurement setup.

  1. https://old.reddit.com/r/oratory1990/wiki/index/list_of_presets

  2. https://headphonetestlab.co.uk/home-welcome

  3. https://reference-audio-analyzer.pro/en/param6.php?ls=1#gsc.tab=0

  4. https://www.stereophile.com/content/innerfidelity-headphone-measurements

  5. https://crinacle.com/graphs/

  6. https://www.audiosciencereview.com/asrdata/HeadphoneallList

  7. https://unheardlab.com/graph-comparison-tool-unheardlabs-squiglink/

  8. https://forum.headphones.com/t/index-collection-of-measurements-made-by-resolve/15251

  9. https://www.rtings.com/headphones/graph/43243/sound-profile/

  10. https://capraaudio.squig.link/Headphones/

I don't have a measurement rig, so I don't have a FR for these headphones. There is one included in the AliExpress listing, but that's a little different from measuring a complete set of headphones with all the mounting, padding, and tuning (of which I've done none). Subjectively, I'd say these are a little bass heavy, even for a bass head. I've just spent so much more time listening to music that I can't be bothered to tune them further. They're pretty good as is!

References

An incomplete list of reading materials on modifying or making custom headphones.

  1. https://www.headphonesty.com/2024/01/grado-modifications/

  2. https://www.instructables.com/Grado-Headphone-Modification/

  3. https://www.nyczaj.audio/post/5-easiest-mods-for-grado-headphones

  4. https://www.symphones.com/shop/v9

  5. https://ellevenacoustica.com/products/

  6. https://github.com/DMS3tv/Open-Omega

  7. https://www.alibre.com/forum/index.php?threads/studio-grade-headphones-on-the-cheap-a-diy-3d-printable-project.22335/

    1. https://www.eevblog.com/forum/projects/studio-grade-headphones-on-the-cheap-a-diy-3d-printable-project/

  8. https://www.head-fi.org/threads/audio-measurements-on-a-headfi-budget.893084/

  9. https://attackshark.ca/blogs/knowledges/40mm-50mm-driver-size-audio-comparison-gaming

  10. https://www.head-fi.org/threads/diy-3d-printed-headphone-journey.979090/

  11. http://douglas-self.com/ampins/books/apad.htm

Tags