200W Portable Lab Power Supply & 100W PD Power Bank
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Portable 200W lab bench supply. Features 150W variable DC output and 100W always-on USB-C PD. 4S Molicel battery pack.
- Rating
- 5 / 5
- Likes
- 9
- Downloads
- 17
- Makes
- 0
- Views
- 238
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- Creative Commons — Attribution — Share Alike
Why did i build it ?
I needed a powerful, portable lab power supply with modern USB-C capabilities. Long story short, looking at the market, there just weren't any good options that combined heavy-duty variable DC output with modern Power Delivery protocols. So, I built my own!
This is a high-performance, fully portable 200W lab bench power supply and 100W USB-C power bank driven by a custom 4S Molicel lithium-ion battery pack. It features an SK150Pro Buck-Boost Converter (allowing precise CV/CC control from 0.5V to 40V) and an IP2368 USB-C Module for 100W bidirectional fast charging.
Bill of Materials
Batteries: 4x Molicel 21700 4500mAh Cells (wired in 4S series) (what i bought https://aliexpress.com/item/1005008793456291.html).

BMS: 4S 30A Lithium-Ion Battery Management System (what i bought https://aliexpress.com/item/1005006620182607.html).

Variable DC Module: SK150Pro 150W CNC Buck-Boost Power Supply (what i bought https://aliexpress.com/item/1005010383922826.html).

USB-C Module: IP2368 100W Bidirectional Fast Charging Module (what i bought https://aliexpress.com/item/1005007208783506.html).

Main Switch: Heavy-duty DPST Rocker Switch (what i bought https://aliexpress.com/item/1005005814871991.html).

Terminals: 2x 4mm Banana Jack Binding Posts (what i bought https://aliexpress.com/item/1005005303202462.html).

Wiring: 16 AWG highly flexible silicone wire for main power runs (what i bought https://aliexpress.com/item/1005008933605669.html).

Primary Monitor: LCD Battery Capacity/Voltage Meter (for detailed percentage and voltage tracking) (what i bought https://aliexpress.com/item/1005007099995173.html).

Quick-Glance Monitor: Basic 4S LED Battery Indicator Bar (for a quick visual check) (what i bought https://aliexpress.com/item/1005009914736899.html).

Fuse: KCD3 2Pin Medium Standard Auto Fuse Holder With 20A Fuse (what i bought https://aliexpress.com/item/1005005182079397.html).

Rubber Feet: 4x Conical Rubber Foot Pads (12mm base x 7mm height) to prevent sliding and protect your workbench (what i bought https://aliexpress.com/w/wholesale-rubber-feet-30pcs-Speaker-Cabinet-Furniture.html).

Enclosure Hardware: M4 Brass Threaded Inserts (M4x8mm, OD: 5mm) and matching M4 screws for a durable, professional case assembly (what i bought https://aliexpress.com/item/1005006937738754.html; https://aliexpress.com/item/1005007654176205.html).


Wiring Guide
Step 1: The Battery Core: Place your four Molicel 21700 cells into the custom 3D-printed battery base. Mount the 30A BMS board securely on top of the pack. Wire the four cells in a series (4S) configuration. Carefully connect the balance cables to the cells as shown in your standard BMS wiring diagram, and then solder the main battery leads to the BMS.
Step 2: Main Switch & Fuse Routing Take the main output wires coming from the BMS (
P+andP-). Route the Positive wire into the input of your Blade Fuse Holder. Then, run a wire from the fuse output into the positive input terminal of your Main Switch. Route the Negative wire from the BMS directly to the negative input terminal of the Main Switch.Step 3: The USB-C Module (IP2368) Wire the power pads of the IP2368 USB-C module directly to those same switch input terminals (the side coming from the battery/fuse, before the switch toggles). This clever routing ensures your 100W USB-C port is "Always On" and ready to charge your phone or laptop, even when the rest of the machine is turned off.
Step 4: Displays & Variable Power The LCD Percentage Display and the basic LED Indicator Bar come with their own pre-attached wires. Take the wires from both displays and solder them directly to the output terminals of your Main Switch. Next, run one thick pair of cables from those same switch output terminals to the input of the SK150Pro (
VIN+andVIN-).Step 5: Final Output Terminals Take heavy-gauge wire and connect the
VOUT+andVOUT-output terminals of the SK150Pro directly to the back of your two 4mm Banana Jack Binding Posts.
Space inside this enclosure is very tight, so cut your heavy silicone wires as short as physically possible; if you leave too much slack, the case simply will not close. Before making that final connection to the Molicel battery pack, use a digital multimeter to verify your polarity and ensure there are no short circuits across your solder joints—these batteries can dump massive amounts of current instantly.
SK150Pro Software Safety Settings
Out of the box, the SK150Pro does not know it is running on a battery; it assumes it is plugged into a wall. To ensure your lithium cells last for thousands of cycles and your 3D-printed case doesn't melt, you must program a custom safety profile.
Press the SET button to enter the system menu, make sure you are editing the Cd00 memory group, and dial in these exact values:
LUP(Low Voltage Lockout) 12.0V:This tells the machine to shut off its output when the battery drops to exactly 3.0V per cell. This gracefully stops the power draw before your hardware BMS panics and triggers a hard shutdown!OTP(Over-Temp Protection) 75°C: The default 95°C is hot enough to warp and melt 3D printing plastics. Lowering this to 75°C protects your enclosure and keeps ambient heat away from your lithium cells.OAH(Over-Capacity Protection) 3.8Ah: It automatically shuts down the output after dispensing 3.8 Amp-hours, preserving a healthy ~15% buffer in your 4.5Ah Molicel pack so it never dies completely.POn(Power On State) OFF: Ensures the front binding posts are dead (0V) when the machine boots up, protecting your delicate electronics from accidental high-voltage.
Printing Instructions
This power supply can generate up to 150W of continuous power, the internal SK150Pro module will get warm under heavy loads.
Material: PETG, ABS, or ASA is strictly recommended. Do not use standard PLA, as it will eventually soften, warp, and deform from the ambient heat generated by the electronics.
Walls & Perimeters: 3 to 4 walls for maximum structural strength and rigidity (especially important for the M4 threaded insert holes).
Infill: 20% to 25% Gyroid infill.
Supports: Minimal supports required You only need to enable supports for the front battery display cutout and the rear fuse box hole. The rest of the enclosure is optimized to print completely support-free.