1 / 9
Bed-mounted nozzle wiper for the cr6se - Brass Brush Head Remix — image 1
1 / 9

Bed-mounted nozzle wiper for the cr6se - Brass Brush Head Remix

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Remixes Dor's bed-mounted wiper to use brass brush heads instead of the Bambu silicone brush.

Rating
0 / 5
Likes
1
Downloads
5
Makes
0
Views
61
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Share Alike

This model takes advantage of the work by Dor who created a nozzle wiper mount bracket that attaches to the bed where the RH stock glass bed retention clip is normally attached.

Design Tips:

  • The height of the brush can not be adjusted during installation.

  • This kit has been designed to place the top of the brush bristles at precisely 6.2mm above the bottom surface of the bed, because that met my specific needs.

  • If your print bed is fitted with a magnetic sheet and a flexible steel sheet, you may find this bracket ideally sized for your needs, too.

  • If, however, this kit does not place the bristles at the height that you want, then you can use the model called "dor_brush-holder_remix_assy.3mf" to split, resize and merge the applicable parts of the bracket, as required.  (I use Microsoft 3D Builder to do my model remixing work.)

Printing Tips:

  • Print in PETG or higher-temp filament material,

  • Print with high% infill (e.g. 55% Gyroid), 4 walls, 4 top and 4 bottom layers

  • Print the main bracket as oriented in the file, using Normal Support.

Installation Tips:

  • If still using the stock TFT display, use the end-plate adapter included with this kit to move the display 20mm to the right.  That prevents the brush from fouling the display.

  • You can re-use the bed clip mounting screws (flat head, M3) and ensure that the heads are below the level of whatever print plate you use.

  • Apply one or more layers of Kapton tape on both the top and bottom of the bracket, before inserting the captive nuts into the mounting holes and mounting it to the bed.

  • (Optionally) Install an M3H4 heat insert into the brush holder mounting hole on the bed-mounted bracket, to avoid the need for a long M3 bolt + nut to attach the holder.

  • The mounting hole through the brush holder is not in the center.  If the mounting hole in the holder does not align with the mounting hole in the bracket, turn it 180 degrees and try again.

  • Orient the brush holder cap so that the M3 bolt you use to fasten the cap to the holder is oriented toward the front of the printer. 

    • The fit of the brush holder is so tight that a bolt head installed at the back of that cap can foul the vertical extrusion and prevent the printer triggering the Y endstop when homing Y.

    • Fit the peg on the inside rear of the cap bracket into the matching hole in the holder, then fit an M3 bolt through the front holes and gently snug that bolt against the brush head.

  • Wire brush bristles tend to be a bit "wild" and prone to getting trapped under the sides of the cap as you install it.  To minimize this problem, fit a small elastic band or a loop of electrical tape around the bristles before fitting the cap.  Remove that only after the cap is securely bolted into place.

Coding Tips:

  • This kit is designed to be used with a CR6 printer running KIipper (e.g. DGUS-Reloaded for CR6)

  • Insert this line into your START_PRINT macro, just before starting to print the purge line:  CLEAN_NOZZLE

  • Insert the gcode_macro from the text file gcode_macro CLEAN_NOZZLE.txt into your printer.cfg.

  • You can run the macro by itself.  It will home if needed, and pre-heat the nozzle, if needed, then it will run the cleaning routine and restore the nozzle heater target to whatever value it was before you ran the macro. (e.g. it will turn the heaters back off, if they were already off when you ran this macro.)

  • You can temporarily override most of the variables by passing new values as part of the command. e.g.:  CLEAN_NOZZLE zag_count=3 will run the macro dividing the X axis steps into 3 instead of the default 5.   See the comments in the macro, to learn more about how to configure and run it.

Tags