1 / 1
Anolex 3060 Evo Ultra 65mm Spindle Mount (70mm x 20mm Bolt Pattern) — image 1

Anolex 3060 Evo Ultra 65mm Spindle Mount (70mm x 20mm Bolt Pattern)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Designed to mount to any Z axis with six M6 bolts spaced 70mm apart horizontally and 20mm apart vertically.

Rating
0 / 5
Likes
0
Downloads
12
Makes
0
Views
42
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

This spindle mount was designed specifically for users upgrading an Anolex 3060 Evo Ultra CNC router to a 65mm spindle while retaining the stock Z-axis carriage mounting pattern, however it will also work with any carriage that uses 4-6 M6 bolts spaced 70mm horizontally and 20 or 40mm vertically.

After searching extensively through Printables, Yeggi, and other model repositories, I was unable to find a mount that properly accommodated a 65mm spindle while matching the factory 70mm mounting hole spacing used by the Anolex 3060 Evo Ultra. This model was created to solve that problem. Yes, there are manufactured solutions out there, but I didn't like the idea of adding adapter plates and small width spindle mounts.

The design prioritizes rigidity by keeping the spindle centerline as close to the Z-axis carriage as possible, minimizing leverage and reducing deflection during cutting operations. Material has been strategically added through a swept-body transition between the spindle clamp and backplate to improve strength while avoiding unnecessary bulk.

Features

  • Designed for 65mm spindles

  • Compatible with the stock Anolex 3060 Ultra 70mm bolt spacing

  • Reinforced swept-body design for improved rigidity

  • Minimal spindle offset from the Z-axis carriage

  • Six mounting bolts for secure attachment to the carriage

  • Four clamp bolts for even spindle clamping force

  • Optimized for engineering filaments such as PPA-CF, PAHT-CF, PET-GF, and similar materials

  • 8mm of material between each clamp face and clamp bolt head, giving strength for even pressure when clamping

Print Recommendations -

Recommended materials:

  • PPA-CF (preferred)

  • PAHT-CF

  • PET-GF

  • PET-CF

  • ASA (use at your own discretion)

For maximum rigidity and long-term stability, a fiber-reinforced engineering filament is recommended.

Suggested settings:

  • 6-10 walls and maximum infill or maximum walls (preferred for maximum rigidity)

  • High-temperature material profile appropriate for the selected filament

  • Print orientation as shown in the model files

Hardware

  • 4x or 6x carriage mounting bolts (6 preferably) - M6x15

  • 4x spindle clamp screws - M4x25 

  • 4x spindle clamp hex nuts - M4

Notes:

Most holes have ~0.4mm tolerance (i.e. if the nominal size of a M4 bolt is 4mm, each M4 sized hole is ~4.4mm) this allows for slight variations in layer line width, but please confirm you layer line thicknesses and be prepared to either drill to dimensions after printing or compensate in your slicer.

Verify screw lengths for your specific machine and hardware configuration before installation. As the backplate of the 3D print is 11mm thick, there is approximately 5mm of thread engagement per mounting bolt when using M6x15 hardware. This has proven sufficient during testing on my machine, but users should evaluate suitability for their own application and cutting loads.

This mount was developed and tested on an Anolex 3060 Ultra CNC router. While it may fit other machines that use a similar 70mm mounting pattern, compatibility with other models has not been verified.

You may be asking why there is a 3mm lip on the top-side of the backplate. On the Anolex 3060 Evo Ultra, the mounting block is recessed about 3mm from the face of the top plate of the Z carriage. Without this lip, you would lose height on the Z-axis as the spindle mount bumps into this plate.

Lastly, over the duration of testing on PET-GF (six months), a 0.32mm compression was witnessed on the spindle mount face behind the M6 mounting bolts. Please monitor bolt tightness for the first few days of mounting for all bolts (add witness marks to bolts if necessary) and adjust torque if necessary. Failure to do so may result in a loose spindle mount or even worse, your spindle slips out of the mount and crashes into the bed because the clamping bolts loosened.

If you find this model useful, please consider posting a make and sharing any modifications or improvements with the community. This design exists because I couldn't find a mount that solved this particular problem, and hopefully it saves someone else the same frustration.

Version History

V1

- Straight-body design

- Tested in PET-GF

V2

- Swept-body reinforcement

- Increased backplate thickness to 11mm

- Added top alignment lip

- Optimized for PPA-CF

Tags