Arco Part Cooling Duct + Rear Extruder Cover
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
New part cooling duct for the Arco, fed with a stronger 5015 fan, mounted in the rear extruder cover.
- Rating
- 0 / 5
- Likes
- 3
- Downloads
- 16
- Makes
- 0
- Views
- 110
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Printer Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial
I wanted to get easier access to the hot end of the Arco extruder and the possibility for better heat break cooling. Since there wasn't a lot of space for extra heat break cooling in the front I made a design which moved the part cooling duct and 5015 fan to the rear extruder cover.
Note of importance!! After this modification, the rear auxiliary fan will no longer be functional!!
Since I never made use of the auxiliary fan in the rear cover, removing this created plenty of space for the new duct I had in mind. The stock Arco fans are not very powerful, so I searched and ordered a stronger fan for this purpose. I found and tested this 24V 8500 RPM 5015 GDSTIME fan with great success.
The air outlet of this fan has a narrow opening, for increased static pressure, as compared to the wide outlet of the stock fan.
The fan needed to be mounted in a slightly different location than the stock fan, so I re-designed the rear cover to make it all work.
I have been printing with this setup since December 2025 and it works really well. Added benefit of this duct in combination with a more powerful 5015 fan, is that overhangs print slightly better than with the stock fan duct.
I am still working on a new heat break cooling solution, but I never was able to replicate the heat creep some people experienced, so there never was any real rush to re-design this. The priority for this is pretty low, so I might even skip it altogether.
For this modification you will need to source the following materials:
1x 24V 5015 narrow air outlet fan (5015 GDSTIME 8500RPM 24V) Make sure you get the narrow air outlet, there are 2 version available!!
2x M3 x 14mm or 15mm bolts
2x M3 washer
1x M3 x 10mm countersunk head
3x brass heat inserts M3 x 4mmL x 4.5mmW
Print setting duct:
I used ASA for the duct, but any high temp resistant material works fine
Set wall generator to Classic instead of Arachne!
3 walls
0.15mm layer height
Use tree supports for the lower portion of the duct. The top doesn't need that, although the slicer might add them anyway. Use the draw on support function to block supports for the top area
Print settings Rear Cover:
I used PETG-cf, but any material except for PLA would work just fine
Wall printing order inside/outside
Gyroid infill 10%
3 walls
0.2mm layer height
10 top and bottom layers
For the integrated support model, print the supports in a material that can easily be removed from the the cover model. I used PLA for the supports and PETG-cf for the cover.
If you want to use regular support, use grid supports for the lower slanted parts of the cover only, the rest prints fine in bridge and overhang mode.
When you remove the rear cover you will need to unplug the rear fan from the rear PCB. When the Pentashield is installed this might be somewhat awkward and hard to see. You can use a small mirror to help you locate the fan cable plug from the rear fan and remove it from the PCB.
The new 5015 fan needs to be prepared before it can fit the rear cover. This is easily done with a small flat screwdriver. The rear cover should be removed from the fan by lifting 2 of the clips of the fan.



I printed the part cooling duct in ASA with a layer height of 0.15mm. Any material that can withstand at least 80C will work fine. When the print has finished you will need to add 1 brass heat insert into the duct.


I printed the rear cover with the integrated supports, where the cover was printed with PETG-cf and the supports with PLA for easy removal. You can of course print the cover with regular supports if you want to. I have included 2 versions, one Multi-material version with supports and one without the support structures.
Multi material

Regular Supports

The regular supported model only needs supports on the slanted lower parts of the cover, everything else is either printed in bridge or overhang mode.
When the model has finished printing, you will need to test fit both the duct and the 5015 fan. If all was printed correctly it all should fit snugly.

Insert the 2 remaining brass inserts into the holes of the rear cover.

Mount the fan duct and secure it with the M3 10mm countersunk screw

Mount the fan by slotting the opening into the duct first and then snap the fan into place. This might be a tight fit, but if everything was printed correctly this should snap right into place with a little added force. Although the cable secures behind the cable clip on the right inside of the cover, I also secured it with an extra piece of duct tape to the fan to prevent the cable form rattling around in the housing during high speed printing.

The cover can now be mounted onto the extruder carriage of the Arco, for this you can use the original 4 screws, the 2 small ones on the lower sides and the 2 longer ones at the rear. Connect the fan cable to the small PCB to finish the process.



When everything is mounted it is recommended to do a new resonance calibration from the printer menu!
If you want to support my work, a coffee would be much appreciated!
https://buymeacoffee.com/3dmadmesh