1 / 4
1 Glass + 2 Spring Steel Sheet Buildplate Bed Plate Holder Stand 235mm for Creality K1 and Ender 3/Pro/Neo/v2/v3/S1/5 - Elegoo Neptune 2/2S/2D, 3/Pro, 4/Pro - Flashforge Adventurer 5M/Pro - with Built-in Feet — image 1
1 / 4

1 Glass + 2 Spring Steel Sheet Buildplate Bed Plate Holder Stand 235mm for Creality K1 and Ender 3/Pro/Neo/v2/v3/S1/5 - Elegoo Neptune 2/2S/2D, 3/Pro, 4/Pro - Flashforge Adventurer 5M/Pro - with Built-in Feet

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This is a remix of t3chguy's "Sheet Holder Ender 3 - 235mm Plate Glass Spring Steel Mix" which has added support feet!

Rating
5 / 5
Likes
12
Downloads
78
Makes
2
Views
371
Reviews
1

Updated at source:

Model information

Category
Accessories
License
Creative Commons — Attribution

This model is a remix of t3chguy's "Sheet Holder Ender 3 - 235mm Plate Glass Spring Steel Mix"

!UPDATE! I've added additional versions with longer support feet, 15mm and 20mm! If your table/desk is extra wobbly or you are prone to knocking things over, try printing one of these options instead of the original 10mm version! 

I have modified t3chguy's original model by adding support feet directly into it, rather than printing them separately (which does not appear to be possible anymore due to a dead link in the description of the original model)

The support feet that I've added extend out from the base of the plate holder by 10mm on either side at both ends of the model. This creates a much more stable holder that should prevent it from falling over due to the weight of the tempered glass bed once it is placed inside. I would still recommend always having at least one of the spring steel sheets inside the holder along with the glass bed to add a bit of counterweight, further preventing the holder from toppling over. Enjoy!

List of printers with 235mm x 235mm bed plates supported by this holder ~ 

(There are likely more but this is the limit of what I wanted to research)

  • Creality

    • Ender Series: Ender-3, Ender-3 Pro, Ender-3 V2, Ender-3 S1, Ender-3 S1 Pro, Ender-3 Neo, Ender-3 V2 Neo, Ender-5, Ender-5 Pro, Ender-5 S1

    • Newer Ender 3 Variants: Ender-3 V3, Ender-3 V3 SE, Ender-3 V3 KE

    • K Series: K1, K1C, K1 SE

    • CR Series: CR-20, CR-20 Pro, CR-10 SE

  • Flashforge

    • Adventurer Series: Adventurer 5M, Adventurer 5M Pro (Note: Flashforge advertises the printing area as slightly smaller, approximately 220mm × 220mm, but uses the 235 × 235mm plate)

  • Elegoo

    • Neptune Series: Neptune 2, Neptune 2S, Neptune 2D, Neptune 3, Neptune 3 Pro, Neptune 4, Neptune 4 Pro (Note: Elegoo advertises the printing area as slightly smaller, approximately 220mm × 220mm to 225mm x 225mm, but uses the 235 × 235mm plate)

Recommended Print Settings ~

  • 0,2mm Layer Height

  • 3 Walls (Inner/Outer/Inner)

  • 30%-50% Infill (3D Honeycomb, Gyroid, or Cubic)

  • If you have issues with warping or bed adhesion. 25% Speed first layer and use a brim

Tags