Airbus A320 Accumulator Brake Pressure gauge
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A 1:1 scale replica of the Airbus A320 accumulator brake pressure gauge, primarily designed for the SimGuy MIP.
- Rating
- 5 / 5
- Likes
- 8
- Downloads
- 124
- Makes
- 0
- Views
- 413
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Other Gadgets
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Update 24/09-2026: Updated resistor link and quarter watt sign.
Update 12/09-2026: Added previously missing LED link and footprints, my bad!
Update 23/08-2026: Added Youtube video Tutorial.
Update 10/08-2026: Updated PCB, pin marking error.
I am selling only PCBs for a small fee, 15€ + shipping. Send me a message if you're interested!
Video Tutorial
Here is my official video tutorial on how to assemble the gauge:
Introduction
This is a 1:1 scale brake pressure gauge that sits on the main instrument panel beside the gear lever. I primarily designed it to be fastened to the SimGuy MIP, 10mm thick panel without any direct screws into it, but it can easily be modifed to fit almost any MIP.
The construction uses one custom PCB with LEDs, a driver for them, a micronontroller (RPI-2040 Zero) and a separate USB-C port to supply power to the Servos. Behind the PCB the three SG90 Servos sit and connect to the front needles.
More photos and assembly video coming soon!
Printing
You will need five different colored PLA filaments, a black, white and green. These can be any brand that you chose. Next you will need a lighter blue for the front frame, I use "Panchroma Matte Muted Blue". And finally you will need a transparent filament, the more see-through the better. for this I used FormFuturas easyFil natural color PLA.
There are two print profiles, one for a 0.4mm nozzle and one for 0.2mm nozzle. You will need to print both of the profiles! The smaller text and details is printed with the 0.2mm nozzle to get higher quality and I highly recommend using the profiles and nozzle sizes. But here are some of the more important settings if you don't use the profiles:
The visible multicolored objects (front panel face and needles) are .3mf files with multiple parts per object. When you load them into your slicer you want to load them as one object with several parts. Next you want to set the color for each of the parts. In the objects tab (prusaslicer/orcaslicer/bambu studio) you will see all the parts and their names. Everything that is named "Body..." is the top white text so chose the white filament. The "front panel" parts are all black filament, the "transparent" are transparent and "green" is green.
The transparent parts should have a lower infill and walls, approximatelt 10% and 2 walls to let more light shine through. The front panel also has ironing turned on and oriented so it goes from side to side for a smoother look.
The other components can be printed with 0.4mm nozzle and regular settings, in black filament.
PCB
I ordered my PCB from JLCPCB and used PCBA (circuit board Assembly) to have them solder on the LED chip (which is a CN5711 chip, and the USB-C port (just search for TYPE-C-31-M-12).
There are a few components on the PCB:
Description/Name | Footprint | JLCPCB Part Number | General part number/name |
|---|---|---|---|
USB-C Port | J1 | C165948 | TYPE-C-31-M-12 |
LED Driver chip | U1 | C35634 | CN5711 Driver Chip |
3mm LEDs | D1-D11 | Didn't order | 3mm Flat Top Warm White LEDs |
1K resistor for LED driver | R1 | Didn't order | 1K ohm resistor |
5.1K resistor for USB-C | R2,R3 | Didn't order | 5.1K ohm resistor |
Potentiometer for LED driver | RV1 | Didn't order | 50K Bourns 3296W trimpot |
The main microcontroller | U2 | Didn't order | Raspberry Pi 2040-Zero |
Male headers for servos | M1,M2,M3 | Didn't order | Male 2.54mm headers |
M2 Screws to secure the board | H1,H2 | Didn't order | M2x6mm screws |
When ordering you must ensure that the "Via Covering" setting is set to "Untented"! This is because the small holes on the bottom of the LED driver chip need to be fully free. The large metal pad is actually a heatsink for the chip.
Bill of Materials [B.O.M]:
Here are all the needed parts, excluding theprinted parts, PCB and it's pre-assembled components:
Qty. | Item | Aliexpress Link |
|---|---|---|
1 | Raspberry Pi 2040-Zero (Made by waveshare) | |
11 | 3mm Warm White Flat Top LEDs | |
1 | 1K ohm standard ¼ W resistor | |
2 | 5.1K ohm standard ¼ W resistor | |
1 | 50K ohm trim potentiometer, Bourns 3296W | |
3 | 1x3 pin male 2.54mm header | |
4 | M2x6mm screws | |
2 | M2x16mm screws | |
6 | M2x4x3.2mm heat set inserts | |
3 | SG90 Servo | |
2 | 1x9 female 2,54mm dupont headers* | |
1 | 1x5 female 2,54mm dupont headers* |
*I highly recommend not soldering the microcontroller directly to the PCB and instead first soldering these female headers and then connecting the controller to these so you can remove it at any time. This is not shown in assembly pictures.
Also you can cut out a round 50mm diameter circle of clear acrylic/plexiglass or similar to use in front of the panel, but it's not strictly necessary.
Assembly:
Start by assembling the PCB, insert the LEDs and resistors in their correct slots and solder. The LEDs should sit completely flush with the board, and ensure polarity! Then insert all the headers and solder and do the same with the trimpot. Then just connect the microcontroller.
Next continue with the panel itself, start with the heat inserts. Use a soldering iron to melt and insert them into their appropriate slots, see the pictures. Then insert the front frame into your Main Instrument Panel and secure it from the back with the black ring. Insert the ring from the back and secure with two M2x6mm screws. Next, if you have an acrylic circle just push it in from the back, if not then use the black printed "acrylic slot spacer" instead. Insert either and then the front text panel, in the correct orientation!
Now screw on the PCB with two M2x6mm screws, also in the correct orientation. The LEDs should slot into their appropriate holes in the front panel. Continue with the back cover, use two M2x16mm screws to fasten it, in the orientation that allows the PCB to "exit" the inner part. Now just use the included screws and fasten the servo motors and plug them in. Do not push in the needles just yet though.
Software/Configuration:
For the software I use something called Mobiflight. It connects to your microcontroller and the simulator and communicates with both units to send appropriate commands. In the mobiflight section of this model I have two files. The .mfmc file is uploaded to the microcontroller and the .mfproj is the actual project you will load up into mobiflight. Start by flahsing the microcontroller.
Connect the microcontroller to your computer and the power USB-C port to a standard 5V power outlet brick. Ensure the power brick outputs 5V. In Mobiflight press extras->settings->mobiflight modules. Here right click your module which will probably be called something like "compatible" and press update firmware and pro micro. Next on the same page press the open button and chose the .mfmc file and click on upload config.
Now open the .mfproj file and start it up. Only now insert the needles in the corresponding way as they are in the simulator to ensure they don't spin too much either way and destroy themselves! Depending on your printer charesteristics you might need to use a hot air gun to slightly warm up the needle ends and then push fit them onto the servos.
Modification
The "back securing ring" file is uploaded in STEP file format to be easily editable. If you have another MIP (not SimGuy's) you can simply make parts of it thicker to reach the MIP and ensure the panel doesn't come loose. It simply "squashes" the MIP panel between the front panel and itself when you tighten the screws. Feel free to reach out to me if you want to modify the ring!
Be sure to check out my other models and feel free to ask any questions if you've got any!