5in3 Hot Swap Drive Bay 5x 3.5" HDD, with front-mount fan
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A five 3.5" HDD hot-swap drive that fits in 3x 5.25" drive bays.
- Rating
- 0 / 5
- Likes
- 8
- Downloads
- 18
- Makes
- 0
- Views
- 362
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Computers
- License
- Creative Commons — Public Domain
5in3 Hot Swap Bay, with front-mount fan
A five 3.5" HDD hot-swap drive that fits in 3x 5.25" drive bays.
by ZeeKay
2026
The intention of this project was to use cheap parts to make a jbod for home NAS systems with short-depth cases. Many options are expensive, loud, extra deep, proprietary, etc. This allows 5 3.5" HDDs to fit in a 3x 5.25" drive bay. This use useful for cases such as Silverstone RM41-506 cases like mine, or possibly up to 15 front-accessible drives with the RM45-360. RSV-R4000U is another good option, as well as the RSV-L4000U. I just wanted something to be able to replace used drives when they die without having to de-rack my whole system out of its small closet.
The front fan allows a full 120mm fan in a push configuration. This should get much more air into the drives vs the traditional 80mm pull fans, or it can be nearly silent. A design goal was maximizing air flow through the bay, more than other options. The overly fancy hinge allows the fan to drop out and away, enough so it doesn't impede inserting or removing the drives at all. This amount of packaging in a tight space was challenging and the linkage seems small but its been more than sufficient in strength.
Performance Notes:
Basically silent to me. Wouldn't hesitate to have this in a system right next to me. Obviously this depends on the fan used. This is with a NF-A12x25.
Cooling - 5 drives (WD100EMAZ), in a 33c ambient server closet, over the past year have ranged from 39c to 45c mean temps. Max temps 50. I've not looked into which positions are hotter or cooler. I also have a magnetic dust filter over the front which likely reduces flow.
Note: Overall installed length is 208mm. In my aforementioned RM41-506, the left side fits fine, but the right interfered with the motherboard power connector on an Asus X99-WS IPMI.
Printed Parts: - PETG suggested for thermals, use CF at own risk (lightly conductive). I used Tinmorry PETG-GF.
1x - Main Body.stl
1x - Linkage Card.stl
1x - PCB Bottom Mount.stl
1x - PCB Top Mount.stl
1x - Door_NoGrill.stl -or- DoorNoctuaGrill.stl (Notctua is separate download)
2x - HDD Bracket.stl (2x per HDD installed, up to 5 HDDs with 10 Brackets)
Print Settings:
STLs should be oriented in optimized print direction, no supports needed
Uses around 440g for a 'full set'
Mostly Default for your Filament - 2 perimeters / 15% cubic infill / 0.40mm nozzle / .20mm layer height
Advanced -> Arachne perimeter generator -> Minimum perimeter width -> 50% - Most printers are fine at this setting and it helps strengthen the linkages
Purchase Parts:
1x - 'JONSBO N1 Backplane' AliEx https://www.aliexpress.us/item/3256806578676856.html "SATA 5 Disk Supports Hot-swappable SAS SATA Upgrades The Hard Disk Power Supply IC" - Green "5-HDD-SATA" marking on pcb Note: Prices seem to fluctuate, link above is commonly the cheapest, but its a generic part
1x - 120mm Fan - Designed around an Noctua A12, however not required. The cutout in the body fits the exact length of the Noctua fan to fit the header and extension
Small Zipties - Used to hold the fan cable to the bottom of the body
Hardware:
M2 Screws - Other than the parts specific to them (ie fan/hdd) all hardware is a couple lengths of M2 button head screws. This was mostly required as a design constraint to get clearances. One multi pack kit will include plenty of hardware to build several of these. https://www.amazon.com/dp/B0DFWXRM21 Actual count:
10x M2x6mm
6x M2x8mm
6-10x M2x16mm - Used for the pcb mounts, 3 ea is probably fine but there's 5 holes in each one for extra strength
4x HDD Screws - #6-32 - Holds HDD to side rails/bracket (4x per HDD)
4x Fan Screws - They hold the fan
Other:
Clear PETG/PLA/Other Filament 1.75mm - This is for the HDD activity LED light tubes. I used clear PETG I had and it works great.
Assembly:
In the following instructions the perspective is given as Up being the side of the bay with the numbers on the top, looking into the body at the numbers. "In" or "Rear" is going towards the direction the unit would be inserted in, the PCB side being the "Rear".
- Take note of the screenshot that shows how the linkage is laid out, really I tried to explain how they looked but it is kinda hard
- Order of parts on sprue from left to right, DoorLock, LeftBodyFrontHinge, LeftBodyBackHinge, DoorBottomHinge, DoorTopHinge, DoorTopHinge, DoorBottomHinge, RightBodyBackHinge, LeftFrontFrontHinge
- Clip the linkage hinge arms from the sprue card, flush to the ends of the linkage arms
- No threading necessary, the holes are sized to allow the M2 hardware to be directly screwed in. Be careful to not overtighten, these are tiny screws.
- Tighten to bottom, then back out about 1/8-1/4 turn or so, to where it rotates but does not have much play.
1. RightBodyBackHinge - long, thick, two holes
1x M2x8mm
- On the bottom right side, it attaches to the hole towards the inner side. Installed orientation should be the flat side facing the wall of the body (to the right) and it should curve slightly outwards if it is in the up position.
2. RightBodyFrontHinge - long, 'Z' shape, 3 holes
1x M2x8mm
- On the bottom right side, it attaches to the hole near the front/closer side with M2x8mm. Fat side attached to body, flat side facing to the right.
3. DoorBottomHinge - long - straight - thin - 3 holes - middle hole offset towards one end
3x M2x6mm
4. DoorTopHinge - short - straight - thin - 2 holes
2x M2x6mm
5->8. Steps for left side are the same, but mirrored
9. Door Lock - its got a finger hole
1x M2x8
- Fit through slot in Door, screw goes from outside to inside
10. Door Lock latch
1x M2x8
- Partially insert screw into top right side of body into the boss, the Door Lock should be able to swing around and lock it
It should be able to test the door opening/closing at this time.
11. PCB Mount
6-10x M2x16mm
- Slot the bottom and top mounts onto the PCB. The 'Bottom' is the side that the sata ports are offset to. They shouldn't really fit the wrong way but you can try. Take the assembly and put it on the back of the body, to confirm it is the right orientation the bottom should be the side away from the drive bay numbers on the front, and the notch for the fan cable should line up. Put 3 or 5 screws per top or bottom based on vibes, 3 is what I used but I'm not swapping drives every 14 hours.
12. Optional - HDD Status/Activity Light Tubes (I think they're neat)
- Snip one end of some clear filament flat. Insert into the the tube path until it sits against the pcb, into the little holder. I'd suggest testing with the filament first by cutting it flat but protruding a bit so you can pull it out if you don't like it. If you do like it, cut it flush with the front. Repeat for all 10 tubes. Should use less than 2 meters of filament total.
13. Add the Fan last. This is because it kinda gets in the way of the other stuff. The cable outlet of the fan should be on the bottom left side, this is so that it can run parallel along the bottom to the channel on the right side. Doing it this way allows the cable to move freely so the door doesn't bind or tug on it. Ziptie the cable through the channel and to the back. The ziptie holes have built in supports than need to be cleared first. This was designed around the Noctua fans that have a short cable, there is a space to place the connector with room for the extension cable to mount everything in the right spot. If you have the Noctua grill version you're good, otherwise add your own, and/or a dust filter to the front.
14. Attach HDD Brackets to hard drives - 2 screws each, the clasp side opposite of the sata connector
15. Install body into chassis - This depends on your system. It won't fit if your bays have the ledges between the slots, your case might be able to be modified. You only need a few screws to hold it in, the ones on the sides are designed with M3 screws in mind.
16. Hook up the power/data cables
17. Insert drives
18. Turn on and see das blinken lights!
License - Do whatever you want. Print it, modify it, sell it.
Future - I'd love to see someone make a version that fits in a 10" mini rack, or a standalone diy disk shelf. The rails/sleds could probably be improved too. Maybe a dual door lock version or some improvements can be made there, it works fine but it could use another revision.