1 / 1
DRYBOX ROLLER- Bearing and Desiccant Base for 4 L Cereal Containers — image 1

DRYBOX ROLLER- Bearing and Desiccant Base for 4 L Cereal Containers

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Bearing-powered spool roller with built-in silica storage for common 4 L filament dry boxes.

Rating
0 / 5
Likes
1
Downloads
3
Makes
0
Views
70
Reviews
0

Updated at source:

Model information

Category
Accessories
License
Creative Commons — Attribution — Noncommercial — Share Alike

Turn a common 4 L cereal container into a practical filament dry box with smooth spool movement and built-in desiccant storage.

DRYBOX ROLLER combines four 608-bearing spool rollers with a large integrated silica-gel tank. Simply install the bearings, fill the tray with desiccant, place it inside the container, and set your filament spool on top.

Main features

  • Four 608 bearings provide smooth, low-resistance spool movement

  • Integrated 151 ml desiccant tank holds approximately 140 g of silica gel

  • Sliding refill hatch allows quick filling and emptying

  • No screws, inserts, glue, or additional fasteners

  • Designed for Ø200 mm filament spools up to approximately 68 mm wide

  • Compatible with standard 1 kg spools and refill spools such as RESPOOL

  • Ventilation slots expose the silica gel to the air while retaining 2–4 mm beads

  • Prints without supports

  • Includes a small bearing-fit test coupon

Required hardware

  • 4× standard 608 bearings, 8 × 22 × 7 mm

  • Approximately 140 g of loose silica gel

  • One compatible 4 L cereal container

  • Optional PC4-M6 fitting and PTFE tube for feeding filament through the container

608ZZ, 608-2RS and open 608 bearings are all suitable.

Bearing installation

The bearings press onto integrated D-profile stub axles.

Each axle includes:

  • A Ø7.4 mm insertion lead

  • A Ø8.2 mm retaining ring

  • A Ø7.9 mm bearing seat

  • A shoulder that contacts only the bearing's inner race

Push each bearing over the retaining ring until it clicks into its seated position. Once installed correctly, the outer bearing race should rotate freely.

Print coupon_stub.stl before printing the complete tray. The coupon allows you to test the bearing fit using very little filament.

A correct fit should:

  • Hold the bearing securely

  • Produce a noticeable click during installation

  • Allow the bearing to spin freely

  • Prevent the bearing from falling off during normal use

Desiccant compartment

The entire lower section of the tray functions as a desiccant tank.

To refill it:

  1. Remove the tray from the container.

  2. Slide out the hatch.

  3. Pour in the silica gel.

  4. Reinstall the hatch.

  5. Place the tray back inside the container.

When the tray is installed, the container wall limits the hatch movement and prevents it from accidentally sliding open.

Use indicating silica gel so you can easily see when regeneration is required.

Remove the silica gel from the tray before regenerating it. Do not place the printed tray in an oven.

Container compatibility

Designed around the common Amazon-style 4 L flip-top cereal-container format sold under brands such as:

  • Vtopmart

  • Skroam

  • Wildone

  • GoMaihe

  • Praki

  • Withosent

Similar-looking containers can have different internal dimensions. Measure your container before printing.

Minimum recommended internal dimensions:

  • Bottom length: 200 mm

  • Bottom width: 84 mm

  • Container opening must allow a Ø200 mm spool to pass through

The printed tray footprint is approximately:

  • 196 mm long

  • 82 mm wide

Spools wider than approximately 68 mm may contact the container walls. This is a limitation of the container size rather than the roller tray.

Verified design details

The design has been checked for:

  • Watertight and printable solid geometry

  • Support-free printing orientation

  • Bearing installation and seated clearance

  • Contact between the spool and all four bearing races

  • Clearance across the supported spool-width range

  • Free movement of the refill hatch

  • Captive hatch positioning inside the container

  • Desiccant storage volume

  • STEP export and geometry consistency

Print settings

  • Orientation: Print exactly as supplied

  • Tray orientation: Flat base on the build plate

  • Hatch orientation: Flat on the build plate

  • Supports: No

  • Layer height: 0.20 mm

  • Walls: 3

  • Infill: 15–25%

  • Material: PLA, PETG or similar

  • Approximate material usage: 144 g for all printed parts

  • Minimum recommended build area: Approximately 200 × 90 mm

The main tray is 196 mm long and will not fit on a 180 × 180 mm build plate without modification.

Files

File

Quantity

Purpose

coupon_stub.stl

1

Bearing-fit calibration test

roller_tray.stl

1

Main roller and desiccant base

hatch_slider.stl

1

Sliding desiccant refill hatch

Assembly

  1. Print the bearing-fit coupon.

  2. Test one 608 bearing on the coupon.

  3. Print the roller tray and sliding hatch.

  4. Press four 608 bearings onto the tray axles.

  5. Confirm that every bearing rotates freely.

  6. Fill the desiccant compartment with silica gel.

  7. Insert the sliding hatch.

  8. Place the tray inside the container.

  9. Position the filament spool on the four bearings.

  10. Install your preferred PTFE filament outlet in the container lid.

Tags