DRYBOX ROLLER- Bearing and Desiccant Base for 4 L Cereal Containers
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Bearing-powered spool roller with built-in silica storage for common 4 L filament dry boxes.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 3
- Wydruki
- 0
- Wyświetlenia
- 70
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Accessories
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Turn a common 4 L cereal container into a practical filament dry box with smooth spool movement and built-in desiccant storage.
DRYBOX ROLLER combines four 608-bearing spool rollers with a large integrated silica-gel tank. Simply install the bearings, fill the tray with desiccant, place it inside the container, and set your filament spool on top.
Main features
Four 608 bearings provide smooth, low-resistance spool movement
Integrated 151 ml desiccant tank holds approximately 140 g of silica gel
Sliding refill hatch allows quick filling and emptying
No screws, inserts, glue, or additional fasteners
Designed for Ø200 mm filament spools up to approximately 68 mm wide
Compatible with standard 1 kg spools and refill spools such as RESPOOL
Ventilation slots expose the silica gel to the air while retaining 2–4 mm beads
Prints without supports
Includes a small bearing-fit test coupon
Required hardware
4× standard 608 bearings, 8 × 22 × 7 mm
Approximately 140 g of loose silica gel
One compatible 4 L cereal container
Optional PC4-M6 fitting and PTFE tube for feeding filament through the container
608ZZ, 608-2RS and open 608 bearings are all suitable.
Bearing installation
The bearings press onto integrated D-profile stub axles.
Each axle includes:
A Ø7.4 mm insertion lead
A Ø8.2 mm retaining ring
A Ø7.9 mm bearing seat
A shoulder that contacts only the bearing's inner race
Push each bearing over the retaining ring until it clicks into its seated position. Once installed correctly, the outer bearing race should rotate freely.
Print coupon_stub.stl before printing the complete tray. The coupon allows you to test the bearing fit using very little filament.
A correct fit should:
Hold the bearing securely
Produce a noticeable click during installation
Allow the bearing to spin freely
Prevent the bearing from falling off during normal use
Desiccant compartment
The entire lower section of the tray functions as a desiccant tank.
To refill it:
Remove the tray from the container.
Slide out the hatch.
Pour in the silica gel.
Reinstall the hatch.
Place the tray back inside the container.
When the tray is installed, the container wall limits the hatch movement and prevents it from accidentally sliding open.
Use indicating silica gel so you can easily see when regeneration is required.
Remove the silica gel from the tray before regenerating it. Do not place the printed tray in an oven.
Container compatibility
Designed around the common Amazon-style 4 L flip-top cereal-container format sold under brands such as:
Vtopmart
Skroam
Wildone
GoMaihe
Praki
Withosent
Similar-looking containers can have different internal dimensions. Measure your container before printing.
Minimum recommended internal dimensions:
Bottom length: 200 mm
Bottom width: 84 mm
Container opening must allow a Ø200 mm spool to pass through
The printed tray footprint is approximately:
196 mm long
82 mm wide
Spools wider than approximately 68 mm may contact the container walls. This is a limitation of the container size rather than the roller tray.
Verified design details
The design has been checked for:
Watertight and printable solid geometry
Support-free printing orientation
Bearing installation and seated clearance
Contact between the spool and all four bearing races
Clearance across the supported spool-width range
Free movement of the refill hatch
Captive hatch positioning inside the container
Desiccant storage volume
STEP export and geometry consistency
Print settings
Orientation: Print exactly as supplied
Tray orientation: Flat base on the build plate
Hatch orientation: Flat on the build plate
Supports: No
Layer height: 0.20 mm
Walls: 3
Infill: 15–25%
Material: PLA, PETG or similar
Approximate material usage: 144 g for all printed parts
Minimum recommended build area: Approximately 200 × 90 mm
The main tray is 196 mm long and will not fit on a 180 × 180 mm build plate without modification.
Files
File | Quantity | Purpose |
|---|---|---|
| 1 | Bearing-fit calibration test |
| 1 | Main roller and desiccant base |
| 1 | Sliding desiccant refill hatch |
Assembly
Print the bearing-fit coupon.
Test one 608 bearing on the coupon.
Print the roller tray and sliding hatch.
Press four 608 bearings onto the tray axles.
Confirm that every bearing rotates freely.
Fill the desiccant compartment with silica gel.
Insert the sliding hatch.
Place the tray inside the container.
Position the filament spool on the four bearings.
Install your preferred PTFE filament outlet in the container lid.