1 / 1
Two-State Magazine - media cards that show shot vs fresh by depth — image 1

Two-State Magazine - media cards that show shot vs fresh by depth

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Shot or fresh is the depth a card sits at, not a sticker. Push it in, it drops below the rim. ARRI Pin-Lock 1/4in.

Rating
0 / 5
Likes
2
Downloads
5
Makes
0
Views
59
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

SHOT/FRESH Magazine — 6-Slot CFexpress Type B Card Holder with ARRI Pin-Lock

Summary

A six-card CFexpress Type B magazine that makes card status physical.

Fresh cards sit 8.6 mm above the rim for quick removal. Shot cards drop into a deeper locked position, 3.4 mm below the rim, where retention ribs hold them securely.

No labels, stickers, color codes, springs, or moving parts.

The problem

Camera departments use different systems to distinguish fresh media from recorded media: flipped cards, stickers, separate cases, or different orientations.

All of these systems depend on remembering the convention or seeing a small visual marking. That becomes unreliable when working quickly, wearing gloves, or operating in low light.

The two possible mistakes are not equally costly:

  • Mistaking a fresh card for a shot card wastes an available card.

  • Mistaking a shot card for a fresh card can erase valuable footage.

This magazine is designed around preventing the second mistake.

The concept

Shot and fresh are not labels. They are two different physical positions.

FRESH position

The card rests on an internal shelf and stands 8.6 mm above the magazine rim.

It can be removed immediately with one gloved thumb.

SHOT position

Push the card toward the storage well. It moves beyond the shelf, drops 12 mm, and finishes 3.4 mm below the rim.

Two internal ribs grip the card in the lowered position.

The state of every card can be identified visually or by touch.

Directional safety

Moving a card from FRESH to SHOT requires one push and gravity.

Returning a card from SHOT to FRESH requires two deliberate movements:

  1. Lift the card 12 mm out of the well against the rib grip.

  2. Slide it 26.5 mm back onto the fresh-card shelf.

There is no direct horizontal path between the two positions.

A card pushed horizontally from the SHOT position toward the FRESH position collides with the shelf face by 3.00 mm. The geometry therefore prevents an accidental straight-line transition between states.

The more expensive mistake is intentionally the harder one to make.

Capacity

  • Holds 6 CFexpress Type B cards

  • Individual FRESH and SHOT position for every card

  • Status can be checked with a fingertip

  • Designed for cards measuring approximately 38.5 × 29.6 × 3.8 mm

ARRI Pin-Lock 1/4-inch mounting interface

The base uses the ARRI Pin-Lock 1/4-inch mounting pattern based on the ARRI INTERFACES v2023-05 specification.

The interface includes:

  • Central 1/4-20 UNC mounting thread

  • Captive 1/4-20 hex nut in a side-entry pocket

  • Eight Ø3 mm anti-twist pin positions

  • Pin holes arranged on a Ø10.4 mm bolt circle

  • 45-degree spacing between positions

  • Re-indexing in 45-degree increments

Many third-party accessories include only two anti-twist positions. This model includes all eight positions from the ARRI interface so the magazine can be mounted in different orientations.

No Kondor Blue geometry or reference files were used.

Why the anti-twist pins matter

A single 1/4-20 screw acts as a pivot. If mounting preload decreases, the attached accessory can rotate around the screw.

The optional steel pins resist this rotation by carrying the twisting load in shear.

Both the magazine and a compatible camera cage use female ARRI mounting faces. The connection therefore uses loose Ø3 × 10 mm dowel pins positioned between the two parts.

Each pin sits approximately:

  • 5.2 mm inside the printed magazine

  • 4.8 mm inside the compatible host mounting point

The pins are optional. A standard tripod mounting point normally has no corresponding anti-twist holes, so the pins provide no benefit when mounting to a plain 1/4-20 screw.

Printing

Print the model with the card slots facing upward, exactly as supplied.

Recommended settings

  • No supports

  • No brim required

  • 0.4 mm nozzle

  • 0.2 mm layer height

  • 4 perimeters

  • 20% infill

  • PLA or PETG

Support-free design

The model was checked for support-free printing:

  • Steep unsupported overhang area: 0.00000 mm²

  • Longest bridge: 11.6 mm

  • Bridge location: captive-nut pocket roof

Dimensions and material

  • Size: 72.0 × 39.8 × 36.0 mm

  • Approximate material use: 62 g in PLA

The printed magazine weighs less than the six CFexpress cards it can hold.

Print the fit coupon first

Print coupon_fit.stl before printing the complete magazine.

The coupon uses approximately 5 g of material and takes around 15 minutes to print. It contains two full-size test slots with the same:

  • Card well floor

  • Shelf transition

  • Upper rib pair

  • Lower rib pair

  • Card clearances

CFexpress Type B card thickness can vary slightly between manufacturers, and published tolerance information is limited.

The coupon lets you test your actual cards and confirm:

  • Cards slide into the slots correctly

  • Fresh cards remain easy to remove

  • Shot cards are held by the ribs

  • Your printer produces the intended clearances

Assembly

  1. Print the fit coupon.

  2. Test the coupon with your own CFexpress Type B cards.

  3. Print the complete magazine with the slots facing upward.

  4. Slide one 1/4-20 hex nut into the side-entry pocket.

  5. Optionally ream two opposite anti-twist holes from Ø2.85 mm to Ø3.00 mm.

  6. Optionally insert two Ø3 × 10 mm steel dowel pins.

  7. Mount the magazine to a compatible 1/4-20 mounting point.

No glue, springs, cords, screws, or printed moving parts are required.

Bill of materials

Item

Quantity

Description

Card magazine

1

Printed part, approximately 62 g in PLA

1/4-20 hex nut

1

Slides into the side-entry captive pocket

Ø3 × 10 mm steel dowel

2

Optional anti-twist pins

Honest limitations

Pin-hole accuracy

The anti-twist pin holes are modelled at Ø2.85 mm and are intended to be reamed to Ø3.00 mm.

The ARRI positional tolerance for the pin interface cannot be reliably reproduced directly by a typical FDM printer. The printed plastic provides the initial location, while the reamed holes and steel dowels carry the anti-twist load.

Retention testing

Shake, vibration, and drop retention have not yet been formally measured.

The geometry controls the possible movement between the FRESH and SHOT states, but it does not quantify the rib grip under severe vibration or impact.

Temperature resistance

PLA has limited heat resistance and should not be left inside a hot vehicle or exposed to high equipment temperatures.

PETG is recommended for better temperature resistance.

Card compatibility

The magazine is designed for CFexpress Type B cards measuring approximately:

  • 38.5 mm long

  • 29.6 mm wide

  • 3.8 mm thick

Always print and test the fit coupon before committing to the complete model.

Manufacturing potential

The design can also be manufactured from 6061 aluminium using two machining setups.

The geometry contains:

  • No enclosed cavities

  • No mechanical undercuts

  • No moving components

  • No spring features

  • No bonded parts

The current body occupies approximately 48% of its overall envelope.

A solid 6061 version of the current geometry would weigh approximately 134 g. A production aluminium version could include additional lightening pockets not included in the printable model.

Files included

  • card_magazine.stl

  • card_magazine.3mf

  • coupon_fit.stl

  • coupon_fit.3mf

  • card_magazine.step

Required hardware

  • 1 × standard 1/4-20 hex nut

  • 2 × Ø3 × 10 mm steel dowel pins, optional

Tags