Wet plate collodion adapter for Hasselblad Polaroid 100 back
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Converts a Hasselblad Polaroid 100 back to shoot wet plate collodion images in both "Polaroid" and 6x6 format.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 10
- Makes
- 1
- Views
- 104
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Photo & Video
- License
- Creative Commons — Attribution — Noncommercial
Have wanted to try smaller format images for a while, so made this conversion for the Hasselblad Polaroid 100 back as I already have a Hassie. I would have liked to make a fully 3D printed holder, but was not confident in how plastic would hold up for the locking mechanism so instead opted to modify an existing Polaroid 100 back. As the film is no longer made these can be had for quite cheap now and you don't need to feel guilty about supergluing stuff into it, I think mine was about US$25-30 shipped from eBay. I assume this should also work for the Mamiya 67 system's Polaroid 100 back, but don't have one - please let me know in the comments if it works!
I first tried to use one of these backs for wet plate just backing the plate with a sponge as I've seen suggested online - unfortunately the interlock failed and the Polaroid back got stuck to my camera for some time until I was eventually able to free it. For this back I opted to open it up and remove the spring for the interlock mechanism as it was already showing some issues (difficult to get to lock onto the back). This means you can now remove the back from the camera with the darkslide out; given how accustomed most wet plate shooters are to large format I don't think this is really an issue and improves the reliability of the back.
I designed it to natively shoot a Polaroid Mini type tintype plate measuring 85mm x 64mm, intentionally keeping the larger margin at the bottom like a traditional Polaroid. There is also an insert that attaches magnetically to make it a 64x64 square, I plan to use this for mini ambrotypes (glass plates) that can then be printed in a medium format enlarger, where the extra margin would just be an annoyance. When not in use, the insert has its own "dock" to keep it in place.
In addition to the filament, you will need some 4x1mm rare earth magnets, CA glue, and an aluminum soft drink/beer can to cut up to make the pressure plate.
Printing is straightforward and you won't need supports, I like to use a 10mm brim for ABS or ASA just to ensure good adhesion to the bed, but PETG will probably be OK if you don't have an enclosure. I just used standard 20% infill. Recommend black filament for the base and lid to ensure light tightness as I think without a Polaroid film back in it the Polaroid back probably leaks a bit of light out the end, and if you want to be fancy, a lighter colour for the 6x6 insert so it's easier to see and doesn't need to be light tight.
Assembly: for the magnets, I highly recommend making a pair of applicators by gluing a magnet of each polarity to the end of a bamboo chopstick, and marking one with a piece of tape (adding a dab of glue to the tip first to seal the endgrain is recommended before glueing the magnet itself on). The bottom is all one polarity, the top and insert are the other.
The base is close, but not quite a press fit for the Polaroid holder, centre it around the opening with an equal amount of space on each side and superglue it in place. I prefer not to use accelerator for this - it should set quick enough on its own, and it allows you to make little corrections as needed if it slides around during installation. Latex or nitrile gloves are nice to have for this part to keep excess superglue off your fingers, if you shoot wet plate you probably have some on hand.
You can use a pair of regular household scissors to cut a strip off an aluminium can, put a slight bend in it by hand, and superglue it to the inside of the back piece. This should give it enough pressure to keep the plate in place, but not so much that it can compromise the clamping force of the magnets.
This model is 100% original (with some inspiration on the lid/light trap dimensions taken from Robert Bieber's large format wet plate holders), but I also have a few accessories for this size/format I've remixed from existing models that can be found by checking my account.
