Twin Motor FPV Mount for the GWS Slow Stick
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Turn your Slow Stick into a Twin Motor Monster. Great VPV Platform and stable with counter rotating props.
- Rating
- 0 / 5
- Likes
- 3
- Downloads
- 50
- Makes
- 0
- Views
- 249
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- RC & Robotics
- License
- Creative Commons — Attribution
Overview
This custom-designed twin motor mount for the GWS Slow Stick transforms the classic airframe into a rock‑solid FPV platform with exceptional stability, visibility, and control authority. By moving the motors forward and splitting them into a counter‑rotating pair, the mount keeps the FPV camera completely unobstructed while adding a noticeable layer of gyroscopic stabilization.
If you fly in windy conditions, or you simply want a Slow Stick that tracks like it’s on rails, this mount delivers. The counter‑rotating props generate opposing torque forces that help dampen roll disturbances, reduce yaw wobble, and maintain heading even when the wind is trying to push the aircraft around. The result is a Slow Stick that feels locked‑in, predictable, and surprisingly capable for FPV cruising.
Works with Kits:
Features
Clear FPV View — Motors are positioned to keep the camera unobstructed for a clean forward field of view.
Counter‑Rotating Stability — Opposing prop rotation creates a subtle gyroscopic effect that improves stability in gusty conditions.
Lightweight & Strong — Printed in PLA with reinforced geometry for stiffness without unnecessary weight.
Easy Installation — Slides onto the Slow Stick boom and secures with zip ties or small screws depending on your build preference.
Compatible With Common Micro Motors — Designed around 2208 1100kv class motors, but adaptable to similar sizes.
Recommended Setup
These are the components I used during testing. They’re not required, but they pair extremely well with this mount. Cut the 10x10mm carbon stick to about 12.5 inches or what ever works with the props you selected.
Stick : 10x10mm Square boom for motor mounts (12-13 inches or 30 - 32mm long)
Motors : 2208-17 1100kv brushless motors
ESCs : 20A ESCs with 3A Bec -- only use one BEC
Props : Gemfan 8045 props, CW and CCW
Landing Gear : 30e to 50e Size Carbon Landing Gear
Filament Used
Printed using Overture Matte PLA with"
Print Settings
Material: Matte PLA
Layer Height: 0.2 mm
Infill: 30%
Perimeters: 3-4
Supports: Optional -- I did not use supports
Orientation: Print flat on the base for maximum strength
Notes
This mount is designed for FPV pilots who want a Slow Stick that can handle real‑world conditions. With the twin‑motor layout, the aircraft becomes significantly more stable and gains enough authority to fly smoothly even when the wind picks up. It’s still the same gentle, forgiving Slow Stick — just upgraded.
Twin‑ESC Wiring Procedure (Slow Stick Twin Motor Setup)
1. Prepare the Power Distribution - Setup
Both ESCs must share the same battery input so they receive identical voltage.
Use a Y‑harness or solder a parallel power lead (battery → two ESCs)
Ensure both ESC red (+) wires join at the battery positive
Ensure both ESC black (–) wires join at the battery negative
Keep wire lengths similar to avoid uneven current paths
2. Disable One ESC’s BEC Output - Safety
Only one ESC should supply 5V to the receiver to avoid regulator conflict.
Identify the 3‑wire servo lead on each ESC (signal, +5V, ground)
On ESC #2, gently lift the plastic tab on the servo plug
Pull out the center wire (red +5V) and tape or heat‑shrink it
Leave signal and ground wires intact
3. Connect ESC Throttle Leads to Receiver - Control
Each ESC must receive its own throttle channel for independent mixing or differential thrust.
Plug ESC #1 servo lead into RC Channel 3 (Throttle)
Plug ESC #2 servo lead into RC Channel 6 (Aux / second throttle)
Confirm your radio mixes or assigns CH6 as the second motor output
Ensure the receiver’s ground pins align with ESC ground wires
4. Verify Motor Rotation Directions - Important
Counter‑rotation requires one motor spinning CW and the other CCW.
Temporarily power the system with props removed
Check motor #1 rotation direction
Swap any two motor wires on ESC #2 if you need to reverse rotation
Install CW prop on one motor and CCW prop on the other
5. Final System Test - Recommended
Ensure both ESCs arm correctly and throttle response is synchronized.
Power the system and listen for both ESC arming tones
Slowly raise throttle and confirm both motors spool up evenly
Test CH6 throttle response or mixing behavior
Secure all wiring with zip ties or heat‑shrink
Summary
This wiring layout gives you a clean, reliable twin‑motor setup for your Slow Stick. With one BEC disabled and both ESCs sharing the same battery input, the system stays electrically stable. Routing ESCs to channels 3 and 6 allows for differential thrust, mixing, or independent control—perfect for your counter‑rotating FPV twin‑motor mount.