1 / 4
Twin Motor FPV Mount for the GWS Slow Stick — zdjęcie 1
1 / 4

Twin Motor FPV Mount for the GWS Slow Stick

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Turn your Slow Stick into a Twin Motor Monster. Great VPV Platform and stable with counter rotating props.

Ocena
0 / 5
Polubienia
3
Pobrania
50
Wydruki
0
Wyświetlenia
249
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution

Overview

This custom-designed twin motor mount for the GWS Slow Stick transforms the classic airframe into a rock‑solid FPV platform with exceptional stability, visibility, and control authority. By moving the motors forward and splitting them into a counter‑rotating pair, the mount keeps the FPV camera completely unobstructed while adding a noticeable layer of gyroscopic stabilization.

If you fly in windy conditions, or you simply want a Slow Stick that tracks like it’s on rails, this mount delivers. The counter‑rotating props generate opposing torque forces that help dampen roll disturbances, reduce yaw wobble, and maintain heading even when the wind is trying to push the aircraft around. The result is a Slow Stick that feels locked‑in, predictable, and surprisingly capable for FPV cruising.

Works with Kits:

Features

  • Clear FPV View — Motors are positioned to keep the camera unobstructed for a clean forward field of view.

  • Counter‑Rotating Stability — Opposing prop rotation creates a subtle gyroscopic effect that improves stability in gusty conditions.

  • Lightweight & Strong — Printed in PLA with reinforced geometry for stiffness without unnecessary weight.

  • Easy Installation — Slides onto the Slow Stick boom and secures with zip ties or small screws depending on your build preference.

  • Compatible With Common Micro Motors — Designed around 2208 1100kv class motors, but adaptable to similar sizes.

Recommended Setup

These are the components I used during testing. They’re not required, but they pair extremely well with this mount.  Cut the 10x10mm carbon stick to about 12.5 inches or what ever works with the props you selected.

Filament Used

Printed using Overture Matte PLA with"

Print Settings

  • Material: Matte PLA

  • Layer Height: 0.2 mm

  • Infill: 30%

  • Perimeters: 3-4

  • Supports: Optional -- I did not use supports

  • Orientation: Print flat on the base for maximum strength

Notes

This mount is designed for FPV pilots who want a Slow Stick that can handle real‑world conditions. With the twin‑motor layout, the aircraft becomes significantly more stable and gains enough authority to fly smoothly even when the wind picks up. It’s still the same gentle, forgiving Slow Stick — just upgraded.

Twin‑ESC Wiring Procedure (Slow Stick Twin Motor Setup)

1. Prepare the Power Distribution - Setup

Both ESCs must share the same battery input so they receive identical voltage.

  • Use a Y‑harness or solder a parallel power lead (battery → two ESCs)

  • Ensure both ESC red (+) wires join at the battery positive

  • Ensure both ESC black (–) wires join at the battery negative

  • Keep wire lengths similar to avoid uneven current paths

2. Disable One ESC’s BEC Output - Safety

Only one ESC should supply 5V to the receiver to avoid regulator conflict.

  • Identify the 3‑wire servo lead on each ESC (signal, +5V, ground)

  • On ESC #2, gently lift the plastic tab on the servo plug

  • Pull out the center wire (red +5V) and tape or heat‑shrink it

  • Leave signal and ground wires intact

3. Connect ESC Throttle Leads to Receiver - Control

Each ESC must receive its own throttle channel for independent mixing or differential thrust.

  • Plug ESC #1 servo lead into RC Channel 3 (Throttle)

  • Plug ESC #2 servo lead into RC Channel 6 (Aux / second throttle)

  • Confirm your radio mixes or assigns CH6 as the second motor output

  • Ensure the receiver’s ground pins align with ESC ground wires

4. Verify Motor Rotation Directions - Important

Counter‑rotation requires one motor spinning CW and the other CCW.

  • Temporarily power the system with props removed

  • Check motor #1 rotation direction

  • Swap any two motor wires on ESC #2 if you need to reverse rotation

  • Install CW prop on one motor and CCW prop on the other

5. Final System Test - Recommended

Ensure both ESCs arm correctly and throttle response is synchronized.

  • Power the system and listen for both ESC arming tones

  • Slowly raise throttle and confirm both motors spool up evenly

  • Test CH6 throttle response or mixing behavior

  • Secure all wiring with zip ties or heat‑shrink

Summary

This wiring layout gives you a clean, reliable twin‑motor setup for your Slow Stick. With one BEC disabled and both ESCs sharing the same battery input, the system stays electrically stable. Routing ESCs to channels 3 and 6 allows for differential thrust, mixing, or independent control—perfect for your counter‑rotating FPV twin‑motor mount.

Tagi