Enteral Feeding Tube Warmer – Flocare Infinity III
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A double-walled, leak-detecting 300 ml warm-water bath that keeps part of an enteral feeding line warm.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 0
- Makes
- 0
- Views
- 53
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Home Medical Tools
- License
- Open Community License v1.1 + GAtt v1 + Micro v1
Why this exists
This passive warm-water bath keeps a coiled section of the feeding tube warm and reduces that temperature loss before the feed reaches the nasogastric tube. Water touches only the outside of the original tube; the feed, pump, giving set and pump settings remain unchanged.
Research in premature and very-low-birth-weight infants points towards warm enteral feeds being better tolerated. In a randomized trial of 30 preterm infants, feeding at 37 °C produced significantly smaller gastric residuals than feeding at 24 or 10 °C (Gonzales et al., 1995). Another trial involving 80 preterm infants reported less apnoea and less need for anti-reflux treatment at 32–34 °C than at 22–24 °C (Uygur et al., 2019).
For our baby, the practical difference was clear: warm tube feeding was tolerated noticeably better than feeding at room temperature. The problem is that even when the feed starts warm, it cools rapidly while travelling through long, thin tubing.
Compatibility
This is a deliberately specialised design. It requires:
a Flocare Infinity III feeding setup;
a second Flocare Infinity Pole Clamp, model 141999, shown in the photos;
a straight Ø25 mm section of the IV pole.
The integrated printed T-profile slides directly into the accessory channel of the aluminium pole clamp. It is not intended as a universal pole-clamp mount.
Features
Double-walled construction: the air gap reduces heat loss from the water bath.
Visible leak detection: three telltale openings in the outer wall reveal water entering the air gap through a leaking inner wall.
Measured fill level: a continuous raised ring inside marks approximately 300 ml.
Upper tube clips: two C-shaped clips retain the incoming and outgoing tube sections.
One-handed grip: eight horizontal rings provide extra grip on a full, wet cup. This is important when carrying the cup with one hand while holding a baby in the other arm.
Drop-in lid: the connected tubing can be laid into the tapered guides from above instead of being disconnected or threaded through holes.
Condensation control: an internal rim guides condensation back into the water bath.
Lid-hanging system: the J-hook lets the lid hang from the pole-clamp screw while the cup or tubing is handled.
Integrated mounting: cup, mounting web and T-profile form one part that slides vertically into the aluminium clamp.
Print settings
The cup was physically tested leak-free when printed on an Original Prusa MK4 with a 0.4 mm nozzle using Fiberlogy Easy PET-G at extrusion multiplier 1.05.
Cup:
Print orientation: upright, opening facing up
Filament: Fiberlogy Easy PET-G
Layer height: fixed 0.15 mm; first layer 0.20 mm
Perimeters: 7
Bottom layers: 7, with a 13 mm solid lower zone
Top layers: 7
Infill: 35% gyroid
Brim: 6 mm, outer only
Support: no
Nozzle: 245 °C
Perimeter speed: 25–30 mm/s
Maximum fan: 30%
Lid: print flat with the visible top surface on the bed, using the supplied 3MF orientation and the same PETG profile. Do not rotate or tilt either part.
Waterproofness depends on the complete combination of printer, filament roll and slicer profile. An extrusion multiplier of 1.05 is not a universal PETG setting.
After every print, fill to the internal ring and perform a cold-water leak test for at least one hour on a dry, absorbent surface. Repeat using water at the intended operating temperature. Any moisture from a telltale opening means the inner wall may be leaking: stop using the cup and reprint it.