AsRock BC250 to AM4 Heatsink Adapter Mount!
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Open up a world of Processor cooling options with this AsRock BC-250 adapter mount to AM4 heatsink mount pattern!
- Rating
- 5 / 5
- Likes
- 41
- Downloads
- 247
- Makes
- 0
- Views
- 1,902
- Reviews
- 2
Updated at source:
Model information
- Source
- Printables
- Category
- Computers
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
ASRock BC250 to AM4 Cooler Adapter
Why Does This Exist?
I wanted better air cooling for the APU in my ASRock BC250 Steam Machine. The existing AM4 adapters I found did not accurately account for mounting height or the offset processor die, so I iterated until I had one that worked.
The APU package is centered between the mounting holes, but the exposed silicon die is not. This adapter intentionally centers the cooler over the actual offset die.
My Temperature Results
Tested cooling setup: Snowman MC75-8 heatsink, Thermal Grizzly PhaseSheet, Noctua Redux 120 mm fan, and 2x Arctic 92 mm fans across the VRMs and backside memory.
Overclocks & Unlocks: CPU w/ 6-cores at 3.85 GHz, GPU unlocked to 40 CUs at 2.1 GHz.
Results: The APU stayed at or below 70C through repeated Cyberpunk 2077 benchmarks, running stable, and scoring HIGHER than a Valve Steam Machine at the same settings.
WARNING: Read this before you print!
Two rules. Break either one and you can crack the die.
The finished adapter must be 7.8 mm tall.
Measure it after printing, annealing, and all post-processing. Too short can put enough pressure on the exposed die to crack it. Too tall keeps the cooler from making proper contact. Light sanding of the PCB mating surface is fine for over-extrusion or isolated high spots. Do not install a warped or out-of-spec part.
If it comes out under 7.8mm, tune your shrinkage compensation and reprint.
That height was validated on one BC250, using a Snowman MC75-8 with its AM4 retention brackets and supplied springs. Other coolers and mounting systems apply different pressure. Verifying your printed part and your installation is on you.
Print it in PC-CF, PPS-CF, or PET-CF.
This part sits under constant spring load for the life of the machine, and in close proximity to hot hardware. Materials that creep will slowly deform under that load, and a part that started at 7.8 mm will not stay there.
PLA, PETG, and PA/Nylon WILL creep, and that includes their CF and GF versions! ABS/ASA-CF is untested.
Prusament PC-Blend Carbon Fiber (PC-CF) is what I validated on.
Annealing the part will help to reduce long-term creep, as well as temperature handling. If you anneal your print, you should measure the dimensions of it AFTER annealing to ensure it didn't deform or shrink.
Print Parameters
0.2mm Layer Height ONLY
5 Walls / Perimeters
40 to 50% Gyroid or Cubic Infill
6 top and bottom layers
Files Included
BC250-to-AM4 adapter STL
Thumb nut STL
CAD source files
Required Hardware
4× M3×8 screws for the AM4 retention brackets
AM4 retention brackets and compatible cooler
If you mount using the cut original heatsink: 4× M3×12 screws
If you mount using the Thumb Nuts: 4x addition Heat Inserts & 4x M3×16 screws
Another WARNING:
Check your retention bracket screw length! Screws that sit too deep can contact the PCB or nearby SMDs. M3x8 with washers cleared my Snowman brackets. Yours may differ.
Recommended Stock Heatsink Cutting
Optional, and not required for the adapter to work. This is just the arrangement I landed on and it solved the VRM and memory cooling at the same time.
Cut the original heatsink into three sections (see photos). You are left with 3 pieces, front / rear VRMs, and the center APU section. The two outer sections stay over the front-side VRMs, installed like stock. The center processor section moves to the rear GDDR6 memory, with 1.5 mm thermal pads or putty. The adapter can then mount to the heatsink's threaded bosses with M3x12 screws.
If you go this route, pull the heatsink off the board before cutting it, then deburr and clean every section thoroughly. Metal debris will destroy the board.
Installation
Install with the labeled BACK toward the rear I/O end of the card. That is what aligns the offset with the die. Check all cooler and component clearances before applying pressure. Use the springs supplied with your cooler. Screwing a cooler straight down makes die pressure much harder to control.
Project and Support
Created for my BC250 Steam Machine project. The full video will be linked here when available.
License
Released under Attribution-NonCommercial-ShareAlike 4.0 International. Distributed derivatives must retain the applicable license and credit Alan Mandic / MandicReally.
Commercial sale of the design, printed copies, or derivatives requires a separate agreement. This project is not affiliated with or endorsed by ASRock.
Affiliate Disclosure
Some links are affiliate links. I may earn a small commission from qualifying purchases at no additional cost to you.