BC-250 Mount for Jiushark JF13K (VRM Airflow Directed)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This is a custom mounting bracket designed to adapt the Jiushark JF13K cooler onto the AMD BC-250 board.
- Rating
- 0 / 5
- Likes
- 5
- Downloads
- 52
- Makes
- 2
- Views
- 301
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
✅ FDM-PRINTED AND CONFIRMED WORKING — feedback and measurements still very welcome
A complete, fully parametric mounting kit to adapt the Jiushark JF13K Diamond top-down cooler onto the AMD BC-250 board. What started as a single bracket is now a small system: the cooler mount itself, a clamping plate for the back of the board that doubles as a 120 mm fan carrier, spring tensioning thumb nuts, and backplate retainers.
The mount is a one-piece design — the arms that reach the board are part of the plate, there is no separate metal bracket to bolt on. Integrated side walls, guide vanes and exit ramps turn the JF13K's two downdraft fans sideways and push the air straight onto the VRM area on both sides of the APU instead of letting it dump straight down.
Everything in this kit is M3. One screw size, one nut size, no heat-set inserts, no soldering iron.
⚠ JF13K cooler version compatibility
Jiushark ships different revisions of the JF13K mounting mechanism:
Two screws per bracket — this is the version this mount is designed for.
Two spring screw-downs (one spring screw per side).
Check which one you have before printing.
📦 What's in the set
Part | Qty | Notes |
|---|---|---|
Mount (monobloc) | 1 | ~64 g, prints flat, no supports |
Clamping plate | 1 | ~26 g, goes on the back of the board, takes a 120 mm fan |
Fan spacer | 4 | ~0.7 g each, 10 mm tall with a Ø4.3 locating spigot |
Tension thumb nut | 4 | ~0.4 g each, takes a standard M3 nut |
Backplate retainer | 4 | ~0.35 g each, takes a standard M3 nut |
All four corner holes are on a 95.75 mm square pattern, matching the BC-250's cooler holes. The fan holes are on the standard 105 mm pattern.
The fan itself is optional — if you don't fit one, print the plate anyway and skip the spacers, the four Ø2.7 holes just sit unused.
🔧 Mounting
Hardware (per build):
4 × M3 × 40 mm socket screws
4 × compression springs, Ø6 mm OD, 0.9 mm wire, 10 mm free length
4 × M3 hex nuts (standard DIN 934, 5.5 mm across flats) for the thumb nuts
4 × M3 hex nuts + 4 × M3 × 12 screws + 4 × M3 washers (Ø9) for the backplate retainers
If you fit the 120 mm fan: 4 × M3 × 40 mm screws
How it goes together, bottom to top:
The M3 screw drops in from underneath, its head recessed in the clamping plate. It passes through the plate, through the board, through the mount, and comes out on top. A spring goes over it into the seat machined in the mount's top face, and the thumb nut screws down onto the spring.
This is the part worth understanding: you set the clamping force by watching the springs, not by feel. Springs are 10 mm free; screw the thumb nuts down until each one measures 8 mm and all four corners carry the same preload, independent of thread friction. Tighten in a cross pattern so the die seats flat, then do a second pass to even the four spring lengths out.
⬛ The clamping plate
It is a cross with bends near the top and bottom so it threads between the GDDR6 memory chips on the back of the board — measured 0 % shadow over the chips, 2.37 mm minimum clearance — so the rear airflow still reaches the memory.
It sits flat against the backplate over 2 560 mm² of contact, and that is the point: the BC-250's backplate is a 1.2 mm sheet held by four standoffs more than 100 mm away from the APU, with thermal putty between it and the GDDR6 chips. Left to itself it will flex under the cooler's clamping load and the putty contact degrades. The plate backs it up over its whole span and keeps it flat.
Four Ø8 bosses pass through the backplate's Ø10 clearance holes and land on the PCB itself, so the corner load also has a direct path into the board, and four Ø4.4 pilots drop into the board's holes so the plate self-locates — you are not juggling four loose washers under the board while starting the screws.
🌀 The 120 mm fan
The plate carries a standard 120 mm fan on its 105 mm hole pattern, on 10 mm printed spacers. The gap matters more than it looks: with the fan bolted flat against the plate the air only gets a 6.85 mm slot to escape, about a third of the fan's own intake area, and it just fights itself. The 10 mm spacers open that to 16.85 mm — 84 % of the swept area — which is where the curve flattens out. Going to 15 mm spacers buys you very little more.
The fan fixings are M3 like everything else. The holes in the plate are Ø2.7 so an M3 screw self-taps straight into the plastic, and the spacers are bored Ø3.2 clearance. Use M3 × 40: 25 mm of fan + 10 mm of spacer + 5 mm biting into the 6.5 mm plate, stopping 1.5 mm short of the flat top face, so a fan screw can never poke through onto the backplate.
Each spacer ends in a Ø4.3 × 4 mm spigot that drops into the fan's own Ø4.5 mounting hole. That is what locates the fan; the M3 screw through the middle only clamps it. Without the spigot an M3 screw would rattle around in a Ø4.5 hole and the fan could shift a millimetre in any direction.
✅ Print status — FDM confirmed
This kit has been printed on FDM machines and it works. The STLs have now gone through other people's FDM printers and onto real BC-250 boards: the hole pattern lines up, the bosses land on the PCB, the parts hold under clamping load. That was the one genuinely open question when this model went up, and it is answered — you can print this with confidence.
I design and prototype on a resin (SLA/DLP) printer, so FDM is the one thing I can't test in-house — which is exactly why those first prints mattered. Two numbers would still help:
Hole spacing. The corner pattern is 95.75 mm. ABS and ASA shrink roughly 0.5–0.8 %, which is 0.5 to 0.8 mm over that span. Nobody has hit a wall with it so far, but if you measure your actual hole-to-hole distance and tell me which material you used, I can publish a shrink-compensated variant for the materials that need one.
VRM temperatures, before and after. The whole point of the side walls and exit ramps is to move air onto the VRMs. I have the geometry; I don't have the thermocouples.
A comment or a Make with your printer, material and results is the most useful thing you can send — it all goes back into the model.
Resin note: standard resin creeps and cracks under sustained clamping load next to parts that regularly run past 70 °C. If you have the choice, print this in FDM.
🖨 Recommended print settings (FDM)
Material: PETG, ABS, ASA or PC. Not PLA — VRM heat will deform it.
Infill: 30–50 %, gyroid or grid
Walls: 4–5 perimeters (the M3 holes and the thumb nut hex pockets need the material)
Layer height: 0.20 mm
Supports: none needed. Both the mount and the clamping plate print flat on their base. The only downward-facing surfaces are the four screw-head counterbore ceilings — 23 mm² each, a 1.5 mm wide annular bridge over a Ø3.4 hole, which any slicer bridges cleanly. The thumb nuts and retainers print small-end-down (their cone narrows going up, so nothing overhangs). The fan spacers print standing, spigot up.
Fan spacer: the wall of the Ø4.3 spigot is only 0.55 mm thick, so give that part a 0.3 mm extrusion width (or 2 perimeters at 0.3) and it comes out solid. It is a locating feature, not a load-bearing one — the screw takes the clamping force.
Fit notes: hex pockets are sized at 5.8 mm across flats for a 5.5 mm nut, which is the usual allowance for an FDM hex pocket. If yours come out loose, the model is parametric — say so in the comments and I will publish a tighter variant.
🙏 Credits
A huge thanks to user makerdog for kindly FDM printing and shipping the parts to me, providing a detailed review of the cooling system, and supplying the photos to illustrate it!
Clamping plate originally derived from NexGen3D's "Clamping Plate – V2", since fully redrawn and parametrised.
Thumb nuts derived from "thumbnut-mount-tensioner-v2" and "thumbnut-back-plate-retainer-v2", redrawn to take a standard M3 nut instead of a heat-set brass insert — no inserts and no soldering iron needed.