SNES & Super Famicom Cartridge Display Stand - All Regions
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Display SNES games in a compact stadium stand with a 2-color sign and filament-saving hex walls. Several sizes available
- Rating
- 5 / 5
- Likes
- 12
- Downloads
- 27
- Makes
- 1
- Views
- 178
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Video Games
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
A compact, support-free stadium display stand for all three SNES / Super Famicom cartridge styles: PAL/EU, North American, and Japanese.
The stepped layout raises each cartridge so the collection is easy to see, access, and rearrange.
The file section includes versions for:
PAL / European SNES cartridges
NTSC / North American SNES cartridges
Japanese Super Famicom cartridges
Note on the North American version: This variant has not yet been physically verified with an original US cartridge. Please print the included test slot before committing to a full stand and check that the cartridge rests fully on both supports and slides in and out easily.
If you test it, I'd greatly appreciate a Make with front and side photos and a note on whether the fit feels loose, snug, or too tight. This will help me verify and refine the US version.
Choose solid or filament-saving walls
Two main stand styles are included:
Solid-sided - simplest and fastest to print (6 slots: ~5 h 30 min, 230 g)
Hex cutouts - saves filament while retaining a strong, rigid structure (6 slots: ~7 h, 190 g)
The hex version uses about 17% less filament, but takes a little longer to print because of the additional perimeter geometry.
Dimensions
Printing: The six-slot variant fit on a 250 x 220 mm build plate, such as the Prusa CORE One.
On display (height from the tabletop to the top of the rear cartridge):
Slots | PAL/EU & Japanese | US |
|---|---|---|
4 | 210 mm | 208 mm |
5 | 249 mm | 248 mm |
6 | 288 mm | 287 mm |
Taller accessories, such as the Super Game Boy, extend above these measurements. The Super Game Boy reaches approximately 323 mm in the six-slot stand.
Printing
The stand is designed to print without supports, in the provided orientation.
Tested settings:
0.25mm layer height
2 perimeters
~1 mm top and bottom layers (for example, 4 top + 4 bottom layers at 0.25 mm layer height)
10% support cubic infill
No supports
Increasing infill should not be necessary. Because the stand prints on its side, the top and bottom shells form large, continuous structural skins. Together with the outer perimeters, these provide most of the stand's strength and stiffness. The infill is only there to support the internal geometry during printing. For additional strength and stiffness, increase the number of top/bottom layers and perimeters rather than the infill.
Print the stand and faceplate separately.
For a two-color faceplate, add a filament change at the first layer of the raised text. No multi-material system is required.
Assembly
Insert the rear support into the back of the stand, underneath the cartridge slot indicated on the side of the support. See photo:

Press the finished faceplate into the recessed front of the stand. Secure it with a small dab of glue or a piece of double-sided tape.

Looking for NES?
This design started as a follow-up to my NES cartridge stand, which uses a compact tip-out layout for easy access:
License and commercial use:
This model is free for non-commercial use under the license shown below.
If you'd like to sell printed copies or use the design commercially, please contact me - I'm happy to discuss a separate commercial license.
The design is fully parametric, so custom sizes can be provided on request.
Nintendo, Super Nintendo Entertainment System and Super Famicom are trademarks of Nintendo. This is an independent fan-made accessory and is not affiliated with or endorsed by Nintendo.