Porsche Cayenne (958, 2015-2018) fire extinguisher mount
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Mount a standard fire extinguisher (First Alert 2.5lbs) under the passenger seat of a Cayenne.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 2
- Makes
- 0
- Views
- 74
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Automotive
- License
- GNU General Public License v3.0
The STL files provided will allow you to assemble a holder to mount a standard fire extinguisher (First Alert 2.5lbs extinguisher 1-A, 10-B:C, 4.5lbs total weight, model EX3622) underneath the passenger seat of a Porsche Cayenne.
This fire extinguisher can be found on Amazon or at Harbor Freight for about $ 25, much cheaper than Porsche's OEM extinguisher and its expensive mount or any other commercial alternative. In addition, it has a much larger capacity.
Compatibility?
The car in the pictures is a 2017 Cayenne with the compartment underneath the seats. These seats have all the adjustment options (and are also heated + cooled) so this mount should work for any version of the seat for the Porsche Cayenne model years 2015-2018.
What to print?
Print one of: Left_end, Left_bracket, Release_top_left, Release_top_right, Right_bracket, Right_end
Print two of: Rod_left, Rod_right, Release_bottom
Print three of: Rod_middle
Print four of: Loop_buckle, Loop_buckle_end
How to choose the Loop_buckle size?
You want the fire extinguisher to clip into place firmly without requiring a lot of force.
I suggest you print two of: Loop_buckle_17mm, Loop_buckle_end_17mm
Then you assemble either the left or the right side and put the fire extinguisher in place. If it is too difficult to close the holder, print one Loop_buckle_18mm (with its end cap) and replace the top loop buckle with this larger one and try again (if the holder is too easy to close, print the 16mm one).
If, after changing one of the buckles, it is still too difficult, replace the bottom buckle with the larger size as well.
Printing orientation?
Flat (the longest dimension on the bed) and no support: Left_end, Right_end, all the Rod_*, all the Loop_buckle_*mm, all the Loop_buckle_end_*mm
On the side, no support: Release_top_left, Release_top_right, Release_bottom
On the side, with support: Left_bracket, Right_bracket
How to mount?
Please look at the pictures to understand how to assemble the holder by itself and then mount it:
- Unbolt the passenger seat by removing the 4 bolts (T27 Torx) on the end of the rails on which it moves
- Tilt the seat back
- Remove the 2 torx screws holding the compartment underneath the seat and KEEP THE 2 SCREWS. Be careful while removing this compartment as you have to push it back a little to "unhook" the back part, the fire extinguisher holder will mount in the same manner. There is also a weird clip on the side closer to the passenger door that holds the compartment in place. I broke that tab but it doesn't matter so don't worry too much about it.
- Mount the fire extinguisher holder in the same way, put the screws in to hold it.
- Put the fire extinguisher inside to make sure it fits snug and the clips hold it well.
- Once happy, bolt the passenger seat back and make sure the fire extinguisher does not block any movements of the seat (it should not).
- If there are no issues, place a piece of paper under the fire extinguisher mount to protect the carpet while you put a few drops of super glue (cyanoacrylate) on all parts that do not move (the loop buckles need to move freely so do not glue them! )
Please ask questions in the comments or let me know how it goes it you decide to print it.
I am very happy with how easy it is to open the holder and the fire extinguisher drops down immediately, ready for use.
