Mini FPS Drone Body!!!

What it is? 

So basically this is as the summary says a mini fpv drone body.... here are its specs ---> 

Specs-->

Designed for mini brushless motors of diameter 6mm (yea u can find those and they should be powerfull enough to lift this drone off and fly pretty well)

Its bottom plate is 60mm x 40mm in size and 2mm in thickness which for this drone should be thick enough if printed with PLA+ or PETG (well CF filaments are the best for this but PLA+ and PETG will work too) 

The top plate is ofc smaller than the bottom plate and sits above it spaced out by the front spacers and the back spacers.

The Optional camera mount is designed only if like you have one of those mini camera's that have folding fingers otherwise if you are using a normal fpv camera you should not require it since it would fit inside the drones body itself.

Assembly Instructions --->

Step1 ---> So basically print all the parts out!!!

Step2 ---> First take the bottom plate of the drone and then super glue the front spacers onto the slots given.

Step3 ---> Next i would suggest u to add the electronics and all the wiring connections before hand other than the battery which shall go on top of the top plate or bellow depending on the orientation u want.

Step4 ---> Now once the front spacers are installed and the electronics have been installed (btw u will have to use epoxy glue or CA glue to hold the 6mm motors for extra support and btw unlike bigger motors u can do this safely without damaging them) now u will need to attatch the top plate. To attatch the top plate u will need to carefully allign the back spacers that are to be printed with the top plate itself into the small depressions given on the back of the bottom plate.

Step5 ---> After test fitting it u will need to super glue (CA or resin) the back spacers along with the top plate by gluing the back spacers into the depressions.

Step6 ---> After that is done you can now either attatch the battery above the drone using velcro or also connect it on the bottom of the drone if you wish to make it look better.

Step7 ---> Now the **OPTIONAL** camera mount - Firstly it is made only for the camera's that have those old folding fingers to be attatched otherwise if you are using a normal fpv camera then you wont need the camera mount since the camera can be mounted inside the drone itself then.

Step8 ---> If u decided to go ahead with the optional camera mount then just go ahead and print it out and this prints as a whole part itself since it would not be structually strong enough and would also be inconvenient to print separately so after you take off the supports for the print then you will need to just super glue it (again resin or CA) to the bottom front of the drones bottom plate. 

Step9 ---> Then you can just go ahead slide your camera's folding fingers in it and screw the camera onto it.

Step10 ---> DONE!!!!! YOUR DRONE IS DONE!!!! (well at least the body is u might have to tune the drone before actually flying but yea mainly done!!!!)

Hope U liked this model!!!!

About me ->

(i really need more github stars and/or more printable downloads ig.)

So.... i am a 16 yr old teenager from India and love 3d modelling, designing custom electronics, PCB's, and making the occasional non vibe coded website!!!

some of my projects on github --->

https://github.com/DhairyaAPImaster/Trainer-RC-Plane

https://github.com/DhairyaAPImaster/Cool-Stuff-USB-HUB

https://github.com/DhairyaAPImaster/TGH-The-great-DIY-Handheld

https://github.com/DhairyaAPImaster/60-Agni

https://github.com/DhairyaAPImaster/Carbsion-Custom-freestyle-libre-Reader

https://github.com/DhairyaAPImaster/an-esp-32-based-snake-game

https://github.com/DhairyaAPImaster/Runway-Hackathon-Landing-Page