Adjustable-Grip Phone Stand for Round MagSafe-Compatible & Qi2 Charger Pucks (54-62.5 mm)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Landscape desk/nightstand stand designed to grip the round magnetic charger puck you own: 54-62.5 mm, 4.4-12 mm thick.
- Rating
- 0 / 5
- Likes
- 4
- Downloads
- 4
- Makes
- 0
- Views
- 55
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Portable Devices
- License
- Creative Commons — Attribution — Noncommercial
A 3-part phone stand (head, jaw, foot) that holds the round magnetic wireless-charger puck you already own and presents the phone in landscape at a 20° tilt, for a desk or nightstand (for example iPhone StandBy mode). Instead of a fixed pocket, a sliding jaw below the puck and two sprung prongs above it are designed to grip any round puck 54.0-62.5 mm across and 4.4-12 mm thick with one print: no measuring and no reprinting when you change pucks. Push the jaw's thumb ledge up: it is designed to lock in 0.7 mm steps, and a flexure spring in the head limits how hard it can squeeze.
Validation status (please read): digitally validated only: CAD geometry and interface checks, slicer checks without supports, spring and stability calculations. It has not been physically printed or tested: whether the ratchet locks and releases as designed on a real print, whether the puck stays in place when the phone is pulled off, whether the tongues keep their shape over months, and whether charging is unaffected are all unverified. All pictures are 3D renders; the nightstand and desk scenes are lifestyle renders, not photos. The phone, puck, cable and props in them are simplified stand-ins, and the clock on the phone is a generic picture. None is a photograph.
Who it is for
For people who already own a round magnetic charger puck, especially a third-party or newer one that a fixed-size pocket may not fit, or several pucks. If you own one puck and have calipers, a one-part fixed-pocket stand prints faster; if you have no puck, a charger with a built-in stand is simpler; if you want to take the phone off with one hand, a weighted stand suits you better. This one is light.
Features
Designed to fit round pucks 54.0-62.5 mm across and 4.4-12 mm thick with one print, for example the Apple 25 W puck (55.5 mm, lab-measured size), Pixelsnap-size pucks (56 mm, lab-measured) and two 60 mm third-party pads (Anker and UGREEN) by their published sizes (10.5-12 mm thick).
Ratchet with layer-built locking faces, designed to lock in 0.7 mm steps; a flexure spring in the head limits the grip: calculated 18-32 N held after pushing to the stop, depending on where the puck falls between two locking steps and how solid the print is (about 15 N at worst for the listed pucks with print tolerances).
Change pucks without tools: push the ledge up to take the load off, hook a fingertip under the flat lips of the four fins, pull straight toward you (calculated about 20 N) and slide the jaw down.
The puck's back rests on small pads and only its edge is gripped, below its front face, so the phone sits directly on the puck.
30 mm clear rear cable window (CAD) for USB-A / USB-C plug heads; the cable runs down a channel on the back, along a groove in the foot and drops to the desk through a rear notch.
Calculated for phones of 170 g or more: tips backward only above about 3.1 N pushed into the screen at the phone's top edge standing on its rim, about 2.7 N on the recommended stick-on bumpers (screen taps are about 0.5-1.2 N); recesses for four 10 mm bumpers (2-3 mm thick) are included.
Camera-bump clearance checked in CAD against Apple's dimensional drawings of 8 iPhone models (iPhone 15 Pro, 15 Pro Max, 16, 16 Pro, 16 Pro Max, 17, 17 Pro, 17 Pro Max), in landscape both ways, for 9 test puck sizes spanning the range (54-62.5 mm, 4.4-12 mm).
Support-free parts; a small rack test block lets you check the jaw's ratchet on your printer before the long head print.
Three phone angles included: 15°, 20° and 25° from vertical.
Which file?
Tilt | Head | Jaw | Foot | Notes |
|---|---|---|---|---|
20° (default) | tilt20_head | tilt20-and-tilt25_jaw | tilt20_foot | foot 104 x 130 mm; STEP files included for this set |
15° | tilt15_head | tilt15_jaw | tilt15_foot | foot 104 x 138 mm (longer for the same stability); stance and thumb ledge raised so the thumb still reaches the ledge |
25° | tilt25_head | tilt20-and-tilt25_jaw | tilt25_foot | foot 104 x 130 mm |
Optional for every tilt: rack_test_block_all_tilts (a short copy of the head's rack and rails to test the real jaw before the long head print). puckgrip_model.py is the parametric CadQuery source (tilt, stance, foot size, clearances); the puck fit is mechanical, not a parameter. It has no command-line entry; with Python + CadQuery: import cadquery as cq, puckgrip_model as m; parts = m.build({**m.PARAMS, **m.PARAM_SETS["tilt_15"]}); cq.exporters.export(parts["head"], "head.stl"). Its comments refer to internal design documents and check scripts that are not part of this upload.
Dimensions
Dimensions are for the default 20° set (the 15° head prints 128 x 118.4 x 21.8 mm and the 15° foot is 104 x 138 mm; the 20° and 25° sets fit a 130 x 120 mm bed, while the 15° foot needs 138 mm along one bed axis).
Foot: 104 x 130 mm, 14 mm tall (15° version: 104 x 138 mm).
Head print size: 128 x 116.5 x 21.8 mm (needs a bed of at least 130 x 120 mm).
Phone tilt: 20° from vertical (15° and 25° versions).
Apple-puck centre about 90 mm above the desk; a landscape phone's lower edge about 44 mm above the foot; about 31 mm of the head and jaw shows below the phone's lower edge.
Grip range: 54.0-62.5 mm diameter, 4.4-12 mm thick. Jaw travel 13.2 mm in designed 0.7 mm steps.
Rear cable window: 30.2 mm clear behind every puck centre (CAD measurement).
Print settings
Material: PETG for the head and the jaw (the puck's charging surface reached about 41 °C in ChargerLAB's tests at 25 °C room temperature; PETG heat deflection 68 °C, PLA 55 °C; the spring and the ratchet hold load). The foot can be PLA or PETG. Do not print the head or the jaw in PLA. Indoor use (not in a car or on a sunny windowsill).
Nozzle / layers: 0.4 mm nozzle, 0.20 mm layers (the ratchet ridges and teeth are sized on 0.2 mm layers).
Walls and infill: head and jaw with at least 3 perimeters (walls) of 0.45 mm and at least 15 % infill. The spring force was calculated for a print like that; with 2 walls the head's spring is softer and the held grip drops below the design value. The foot can use any normal setting.
Supports: none. PrusaSlicer shows a print-stability warning (low bed adhesion / long bridges) for the jaw: do not add supports or a brim; they would fill the tongue slots and the bridged gaps. The jaw has a small footprint: print it on a clean bed with a good first layer; if it lifts, reprint it rather than adding a brim or supports (it is a short print).
Orientation: all STL files are already oriented for printing, so do not rotate them: head back face down; jaw back face down (fins up); foot upside down on purpose (its top face on the bed); rack test block flat.
Colour: one colour for all three parts looks calmest on a nightstand (the renders show an off-white print; the accent-coloured jaw in the feature images only explains the mechanism).
Print time and filament for the 20° set are PrusaSlicer 2.9.6 estimates, not measurements. A generic slicer profile (0.4 mm nozzle, 0.20 mm layers, 3 perimeters, 15 % gyroid, slow bed-slinger speeds), PETG: head 5 h 17 min / 61.9 g; jaw 1 h 02 min / 10.6 g; foot 3 h 22 min / 50.2 g; rack test block 56 min / 13.6 g; core set (head + jaw + foot) 9 h 42 min, 123 g (the 15° set takes about 12 min and 3 g more). Prusa MK4S HF0.4 "0.20mm SPEED @MK4S HF0.4" with "Generic PETG" presets (15 % grid; perimeters raised from 2 to 3 for the head, jaw and test block, 2 for the foot): head 1 h 56 min / 59.1 g; jaw 26 min / 9.7 g; foot 1 h 13 min / 45.7 g; rack test block 19 min / 13.0 g; core set 3 h 35 min, 115 g.
Assembly
Optional, before the long head print: print the jaw and the rack test block. The block has one open end and a wall at the other. Slide the jaw in at the open end, pads first, fins toward you. Push its bar toward the wall: it should lock in steps. Press the jaw back toward the open end: it should hold. Push the bar a little toward the wall, pull the fins toward you, and it should slide back out. Optional hang check: hold the block with the open end down (like the dock), anchored, and hang about 4 kg from a string looped round the jaw's push bar for 72 h, a few cm above a soft surface and away from children and pets; the jaw should not have slipped.
Slide the jaw into the head's rails from below, fins toward you, only until it first locks.
Press the head's neck into the foot's socket until the two barbs catch. Carry the dock by the foot.
Stick four round self-adhesive rubber bumpers, 10 mm across and 2.0-3.0 mm thick, into the recesses under the foot (10.5 mm across, 1.0 mm deep), so they stand 1-2 mm proud of the rim. Bumpers 1 mm thick or thinner sit flush and do nothing. On its bare rim the dock can slide at about the force of a screen tap.
Cable: centre-exit pucks: pass the plug through the round rear window, press the cable into the channel on the back and the groove on the foot; it drops to the desk through the rear notch. Edge-exit pucks: turn the puck so the cable leaves sideways through one of the head's open side windows, on the side away from the phone's camera.
Use
Take the phone off. Rest the puck on the jaw's two pads under the two upper prongs. Hold the foot with one hand and push the thumb ledge up with the other thumb until it stops: a firm push at the very end (calculated about 44-48 N, roughly like pressing down 4.5-5 kg); stopping earlier holds the puck less firmly. Let go. Attach the phone in landscape.
Putting the phone on and taking it off: hold the foot with your other hand (the magnet pulls the dock toward the phone as it comes close, too). By calculation the dock with its puck weighs about 165 g and has no ballast: sliding the phone up tips it back at about 1.1 N or lifts it, and a straight pull tips it forward at about 0.7-0.8 N, while any magnet strong enough to hold the phone pulls harder than that.
To change pucks: take the phone off, push the ledge up with your thumb until the jaw moves (this takes the load off the teeth and needs about the same push as tightening), hook one or two fingertips under the flat lips of the four fins, pull straight toward you (calculated about 20 N; about 26 N if the teeth are still loaded) and let the jaw slide down.
Limitations
Not physically printed or tested yet (see Validation status).
Phone removal is two-handed: the dock is light and moves whichever way the phone is taken off.
Holding the puck against a straight pull relies on friction (calculated roughly 8-21 N from PETG-on-steel friction data; PETG-on-anodised-aluminium friction is not published) and has not been measured.
Round pucks only (54.0-62.5 mm, 4.4-12 mm); no square pads, no pucks with a built-in kickstand or finger loop.
Pucks thicker than about 8 mm are gripped on the rear 3.8 mm of their edge; a strongly rounded or tapered rear edge could let the clamp push such a puck forward.
Pucks wider than about 57 mm (for example many 60 mm pads) reach under the camera plateau of the iPhone 15/16/17 Pro models themselves, so the phone may not sit flat on them in any stand.
Landscape only: in portrait the phone's lower half would rest on the jaw's thumb ledge and release fins, which stand up to 12 mm in front of the puck's back (13 mm on the 15° version), so the phone could not sit on a puck thinner than about 12 mm (no magnetic hold, no charging).
Camera clearance was checked only for the 8 iPhone models listed above. Other phones (all Android phones, iPhone 15/15 Plus/16 Plus/16e/Air/17e) are not checked.
Stability is calculated, not measured, for phones of 170 g or more and the part masses of the generic profile (about 120 g for the 20° set, modelled); lighter phones (e.g. iPhone 12/13 mini) and lighter prints (e.g. the 2-perimeter foot of the MK4S SPEED preset) give somewhat lower values. All checks use bare phones; phone cases (including magnetic cases) were not analysed. Standing on its bare rim the dock slides at about 1.2 N on a smooth surface before it tips (use the bumpers); it tips forward at about 1.4 N if the phone's top edge is pulled toward you (20° set; the 15° set slides at about 1.1 N and tips forward at about 1.3 N; about 1.0-1.2 N on the bumpers, whose contact points sit 8 mm inside the rim). The on-bumper figures assume bumpers 2-3 mm thick, i.e. the dock raised 1-2 mm.
The thumb ledge is sized for an average thumb: by a 2D model a 16 mm thumb pad gets 9.7-10.7 mm of contact, a 20 mm thumb only about 4 mm at the 62.5 mm puck (use a finger instead).
Fan-cooled or vented pucks are not checked (their edges may carry vents).
Some of the four tongues rest slightly flexed on ridge tops while the jaw holds a puck; they may take a small permanent set over months (untested). The rack test block's hang check is the way to check a print.
The 20° and 25° sets need a bed of at least 130 x 120 mm; the 15° foot (104 x 138 mm) needs 138 mm along one bed axis. Print time is long with a conservative profile (see Print settings).
Pictures
All pictures are 3D renders of the CAD model: a lifestyle render on a nightstand (the cover), the three-puck grip comparison, a labelled mechanism view, a second lifestyle render on a desk, the four printed parts laid out, a labelled exploded view with the stick-on bumpers, the cable path, a side view with dimension arrows and the three tilt versions side by side. In the lifestyle renders the dock is the exported CAD model; the phone (showing a generic clock picture), puck and props are stand-ins. The accent-coloured jaw only explains the mechanism. They are not photographs of a print.
MagSafe and iPhone are trademarks of Apple Inc.; Qi2 is a trademark of the Wireless Power Consortium; Pixelsnap is a trademark of Google LLC. This design is not affiliated with or endorsed by them. Images are renders of the CAD model, not photographs; the puck, phone and cable in them are simplified stand-ins.