1 / 5
Hand-Crank Card Shuffler with Real Gear Train (Multicolor) — image 1
1 / 5

Hand-Crank Card Shuffler with Real Gear Train (Multicolor)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

One crank, real involute gears: two rubber wheels feed cards from tilted trays into the middle. 4 colours, no supports.

Rating
0 / 5
Likes
0
Downloads
4
Makes
0
Views
45
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — NoDerivatives

A hand-crank card shuffler for family card and board games. Put half a deck in each tray, turn the crank, and the cards drop one by one, alternating, into the middle. One crank drives both rubber wheels through a real involute gear train, so both always push towards the centre.

How it works

  • Two trays tilted 12° towards the centre. Under the inner end of each tray turns a roller with 3 rubber rings that stick out 0.4 mm above the floor and grip the bottom card.

  • A gate sits 0.55 mm above the rubber: one card (0.3 mm) slides under it, the rest of the deck stays behind. The card falls into the central well.

  • Gear train (module 1.5, 20° pressure angle, real involute teeth, 0.24 mm backlash): crank gear 30T drives the right roller 20T directly, and the left roller 20T through a 24T idler. That idler is why the two wheels turn in opposite directions and both push inwards. Turn the crank clockwise.

  • One crank turn = 1.5 roller turns = about 126 mm of rubber, so roughly 2 cards per side.

  • All shafts are printed D-shafts (6 mm); the flat drives the gears and rollers.

Details

  • Cards: standard 63 × 88 mm and also 57 × 89 mm. One 52-card deck per tray (15.6 mm); the central well holds 104 shuffled cards. Diamond-shaped windows in front and back to take the stack out.

  • Size: 232 × 112 × 108 mm (140 mm deep with the crank). Built in 3 body parts so it fits the A1 mini bed: centre chassis + 2 side wings that slide down onto vertical dovetails (0.25 mm clearance).

  • Rubber: 6 standard O-rings 20 × 3 mm (NBR 70, 3 per roller; the groove is Ø21 so they stretch 5 % and stay put), or print the 6 optional rings in TPU (STL included).

  • Decoration: front cover printed face-down with flush inlays (cream frame and dial, red heart and diamonds, black spade and club, small HANMA). Crank gear with the four suits cut out as windows. Faceted diamond relief on the sides, cream rim on all top edges.

  • No supports on any part: horizontal holes are teardrops, all overhangs are 45° or less, open-bottom hollows with 45° roofs save plastic.

Print (Bambu A1 mini + AMS lite, PLA, 0.2 mm)

  • Chassis: 4 h 52 min, 181 g (green + cream rim, colour change only in the last 3 layers).

  • Wings (both on one plate): 5 h 18 min, 183 g (green + cream rim).

  • Front cover, 4 colours: 59 min, 30 g (colour changes only in the first 3 layers).

  • Gears (cream): 50 min, 16 g. Gates + knob (red): 34 min, 19 g. Rollers, shafts, crank arm (black): 1 h 30 min, 32 g.

  • Total: about 14 h 05 min and 461 g (green 390 g, black 32 g, cream 20 g, red 19 g). Colours: felt green, cream, red, black.

Assembly

  1. Slide each wing down onto the chassis dovetails.

  2. Fit the O-rings, drop each roller into its slot from above, push the long D-shaft in from the front through the roller into the blind hole at the back.

  3. Put the gears on their shafts (idler and crank shafts in the front holes), press the cover's 4 pegs into the front wall.

  4. Push the crank arm onto the crank shaft and snap the knob onto its pin. Drop the gates into their grooves.

How it was checked

Collision volumes in OpenSCAD (manifold) for the real parts in place. Gears: no contact in 36 crank positions (every 10°) with the correct tooth phase (0.0000 mm³), and none against the chassis or the cover. Controls that must fail, and do: the right gear half a tooth out of phase hits the crank gear (58 mm³); with zero backlash the teeth touch (0.57 mm³), so they really mesh and are not just far apart. Direction: the mesh graph is read from the actual gear positions (C-R, C-I, I-L); with the crank turned clockwise the left rubber moves towards +x and the right one towards -x, confirmed again with the gear phases (1° of crank = 1.5° of roller). Control: without the idler the left wheel pushes the wrong way. Cards: a 52-card deck (63×88 and 57×89) fits each tray with 0 mm³ and rests on the rubber (0.12 mm lower it touches the O-rings); a single card travels the whole exit path (0-64 mm, 17 steps, both sides) touching nothing; 104 cards fit the well. Controls: a block of 2 cards (6.4 mm³) and of 3 cards (38.8 mm³) hit the gate. All 17 parts against each other: 0.0000 mm³; the crank turns a full circle touching nothing; a D-shaft turned 12° in its gear collides, so the flat drives. Every plate: no overhang over 45° (0.3 mm² at most), no floating parts, colours do not overlap, all within 175 × 175 mm.

OpenSCAD source included: card size, gate gap, tilt and gear sizes are parameters.

About this design

Designed with AI assistance and checked in code before release (see above). Pictures are 3D renders and the slicer preview, not photos. Not printed yet: makes and feedback are very welcome.

Tip: the 0.55 mm gate gap depends on your rubber and printer. If cards jam, sand the bottom edge of the gate a little (bigger gap). If two cards come out together, stick a strip of tape along that edge, or set GAP smaller in the .scad and reprint the chassis.

Español

Barajador de cartas de manivela para juegos de mesa en familia: medio mazo en cada bandeja, das vueltas y las cartas caen alternadas al centro. Una sola manivela mueve las dos ruedas de goma con engranajes evolventes reales (con intermedio para que ambas empujen hacia dentro). Cartas 63×88 y 57×89, juntas tóricas 20×3 o anillos de TPU. Sin soportes, 4 colores, unas 14 h y 461 g.

العربية

جهاز لخلط أوراق اللعب يعمل بذراع يدوي، مناسب لألعاب الطاولة العائلية. ضع نصف الأوراق في كل صينية وأدر الذراع، فتسقط الأوراق بالتناوب في الوسط. ذراع واحد يحرك العجلتين بتروس حقيقية. يناسب أوراق 63×88 و57×89 مم. بدون دعامات، بأربعة ألوان، حوالي 14 ساعة و461 غراما.

Tags