The Shot: Hand-Crank Football Automaton (Kinetic, Multicolor)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Turn the crank: the player kicks the ball into the goal and it rolls back by itself. Real cams, hip and knee. 4 colours.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 9
- Makes
- 0
- Views
- 43
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Toys & Games
- License
- Creative Commons — Attribution — Noncommercial — NoDerivatives
The GIF shows the real movement, rendered from the same 36 crank positions the code checks.
"The Shot": a hand-crank football (soccer) automaton. Turn the crank and the little player winds up, whips his leg and shoots the ball into a goal with a net. The ball rolls back by itself down a ramp along the front of the stadium, waits at a small gate while the leg winds up again, and drops onto the penalty spot for the next shot. Endless loop, no batteries.
How it works
One crank shaft carries two cams, visible through the side window of the stadium box.
Kick cam (snail shape): it lifts a follower rod slowly over 260° of the crank (the leg winds up), then lets it drop over 40°: the rod falls, a connecting rod turns the thigh lever and the leg swings through.
The leg has a real hip and a real knee. A small four-bar link between the hip and the shin bends the knee to 77° when the leg is back and snaps it straight through the shot (28° at the contact, straight in the follow-through), like a whip.
Gate cam: a lime gate rises in the return channel and holds the ball while the leg winds up. With only one crank, the leg goes back the same way it kicked, so without the gate it would hit the returned ball. The gate drops at 242° and the ball rolls onto the spot.
The goal sits on a curved slope: the ball climbs it, falls into a channel behind the crest, leaves the goal through the side net and comes back down the ramp at 8.6°.
Details
Size: 152 × 100 mm base (118 mm deep with the crank), 143 mm tall. Ball Ø18 mm, printed in two halves with classic panel seams.
Pitch with mowed stripes and white lines (penalty box, goal area, penalty spot ring, the D) inlaid in the first layers, small HANMA logo on the grass and on the crank. Stadium stands as ribs on the box walls, octagonal window, number 10 on the player's back, boots with three stripes.
Colours (AMS, 4 slots): dark green, lime, white, red. The player is printed standing, so its colours change by height (boots, socks, shorts, shirt, hair).
Pins: six short pieces of 1.75 mm filament (holes 2.4 mm where a part turns, 1.9 mm where it stays). A drop of glue on the cams and crank (D-shaft) and on the square pegs.
No supports. The box prints upside down (pitch on the bed), the goal upside down, everything else flat or standing.
Print (Bambu A1 mini, PLA, 0.2 mm, sliced with the included 3MF files)
1. Box with pitch: 2 h 44 min, 106 g (green 99 g, lime 6 g, white 1 g).
2. Return ramp: 1 h 01 min, 35 g white.
3. Goal with net: 1 h 03 min, 7 g white.
4. Player and all mechanism parts (4 colours): 5 h 28 min, 74 g.
Total: about 10 h 17 min and 222 g (green 99, white 81, lime 28, red 14).
Turn the crank at about one turn per second. The drop is driven by gravity and keeps up to about 1.2 turns per second.
How it was checked
Cams: the real follower tip resting on the real cam outline follows the design curve within 0.002 mm in 720 positions. Pressure angle 15.5° on the kick cam and 30.8° on the gate cam while it pushes. Control: a cam 1 mm larger leaves the curve by 2.4 mm, and 1.5 mm larger hits the follower guide.
Full 360° cycle: 126 positions (every 5°, 41 around the shot and every GIF frame) with zero intersection volume between all parts, including the filament pins. Smallest clearance between parts that move against each other: 0.29 mm. Control: the connecting rod pushed against the thigh gives 0 mm.
The shot: the boot touches the ball at crank angle 25.7°, the same angle where the toe reaches its top speed (100 % of its maximum over the whole cycle). It pushes the ball 3° above horizontal, so it rolls instead of jumping. Toe speed: 1.77 m/s at one turn per second; the ball needs 0.58 m/s to climb into the goal. Control: with the ball 5 mm further back the boot touches it earlier, outside the top-speed moment.
Return path, measured with a ball resting on the real meshes: smallest slope 8.41° (at least 8°), largest step 0.05 mm, 0.08 mm where the ramp meets the grass (at most 0.5 mm). Control: the same ramp at 2° fails (the ball would stay).
Gate control: without the gate, the boot hits the returned ball in 16 positions between 125° and 200° while it winds up; with the gate the ball waits more than 15 mm away.
Printing: every part fits the 175 × 175 bed, no overhang above 45° except short bridges (window edge, peg holes), no floating islands, colours without overlap. Control: the goal printed standing has 1647 mm² of unsupported net roof.
About this design
Designed with AI assistance and checked in code before release (see above). Pictures are 3D renders and the slicer preview, not photos. Not printed yet: makes and feedback are very welcome.
Español
Autómata de manivela "el chut": giras la manivela, el futbolista arma la pierna (cadera y rodilla articuladas) y chuta el balón a una portería con red. El balón vuelve solo por una rampa, espera en una compuerta mientras la pierna se recoge y cae en el punto de penalti. Dos levas en un solo eje, visibles por la ventana. 4 colores AMS, sin soportes, unas 10 h y 222 g. El GIF muestra el movimiento real.
العربية
دمية ميكانيكية بذراع يدوية: أدر الذراع فيرفع اللاعب ساقه (مفصل ورك وركبة) ويسدد الكرة في مرمى بشبكة، ثم تعود الكرة وحدها عبر منحدر وتنتظر عند بوابة صغيرة حتى تعود الساق، ثم تسقط على نقطة الجزاء. كامتان على محور واحد تظهران من النافذة. أربعة ألوان، بلا دعامات، نحو 10 ساعات و222 غراما. الصورة المتحركة تظهر الحركة الحقيقية.