1 / 4
Mini Strandbeest - 12-leg Theo Jansen walker, hand crank, filament pins (multicolour) — image 1
1 / 4

Mini Strandbeest - 12-leg Theo Jansen walker, hand crank, filament pins (multicolour)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

12-leg Jansen walker: turn the crank and it walks. Foot path, balance and assembly checked in code. GIF of real motion.

Rating
0 / 5
Likes
0
Downloads
7
Makes
0
Views
34
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — NoDerivatives

The GIF is an animation of the real motion: the same 36 crank positions that were checked in code, rendered frame by frame. The floor grid moves exactly as far as the body walks, so the feet on the ground stay still on it. A mini 12-legged Strandbeest with Theo Jansen's linkage: turn the crank and it walks, 67.6 mm per turn.

How it works

Each leg is Jansen's eight-bar linkage with his "holy numbers" (a = 38, b = 41.5, c = 39.3, d = 40.1, e = 55.8, f = 39.4, g = 36.7, h = 65.7, i = 49, j = 50, k = 61.9, l = 7.8, m = 15) at half scale. The crank turns in a circle and the foot draws the famous curve: a long flat, horizontal bottom where it pushes (within 1 mm of the floor for 52.1% of the turn, within 0.2 mm for 34.9%) and a quick lift of 11.2 mm to come back. Six modules, each a front leg and a mirrored rear leg sharing ONE crank pin, are spread at 0/120/240° on each side, so there are always at least 2 feet down per side and the body glides at a constant height.

Details

  • Size: about 104 mm long, 168 mm wide (with the hand crank and hub cap) and 77 mm tall. 12 legs, 72 links, 7 truss frames.

  • Jansen-style colours: yellow "PVC tube" bars with cream tape bands and a groove, cream triangles with a yellow rim, orange washers and toes, teal truss frames with yellow tubes, cream rivets and an orange bearing ring. Small HANMA on the end frame.

  • All links print flat. Pins are plain 1.75 mm filament from your spool: moving joints have Ø2.36 mm holes (0.30 mm clearance), heads are mushroomed with a soldering iron (Ø3 × 0.5 mm, they live in the 0.9 mm gaps between layers). The crank pin is pressed into the crank arms and the fixed pivot B into the frame bosses (Ø1.80 mm holes, a drop of glue).

  • The crankshaft is built from 12 crank arms keyed on 7 hex journals (Ø5.6 mm round where it turns in the frame, 0.30 mm clearance), so no shaft crosses the legs.

  • Filament pins to cut (mm, including 1.5 mm per head), per module: A 18.1, B 13.9, B' 13.9, C 8.6, C' 8.6, E 8.6, E' 8.6, F 11.9, F' 15.2, G 8.6, G' 8.6. About 0.75 m of filament in total.

Printing

  • Bambu Studio, A1 mini + AMS lite, 0.2 mm layers, no supports. AMS: 1 yellow, 2 cream, 3 teal, 4 orange. Colours are only in the top 2 layers of each part, so few colour changes.

  • Plate 1 (triangles + end frame): 1 h 42 min, 32 g (amarillo 2 g, crema 24 g, verde 4 g, naranja 2 g).

  • Plate 2 (bars + washers): 1 h 26 min, 23 g (amarillo 18 g, crema 5 g, naranja 0 g).

  • Plate 3 (frames + crankshaft): 4 h 44 min, 68 g (amarillo 3 g, crema 2 g, verde 37 g, naranja 26 g).

  • Total: 7 h 52 min, 123 g including purge. The rear-leg triangles (T1', T2') are mirror images: they are already mirrored in the files.

Assembly (per module, from the crank side outwards)

  • 1. Push a hex journal through the frame bearing and a crank arm on it; press the crank pin (18.1 mm) into the arm.

  • 2. On the table, pre-assemble each leg WITHOUT bar K: J, T1, CB, FB, T2 with pins C, E, G (heads on both sides). Push pin F through CB + T2 from the inside (head on the inside).

  • 3. Slide the front leg onto pivot B and the crank pin, then the rear leg onto B'; mushroom the B heads. Add K on the crank pin and F, head F; add the washer and K' on F', head F'.

  • 4. Press the second crank arm onto the crank pin and the next journal, then the next frame onto the posts (a drop of glue on the pegs). Repeat 6 times; hand crank on one end, hub cap on the other.

How it was checked

  • Foot path: stance within 1 mm for 52.1% of the cycle (≥ 50%) in one piece, the foot always moving backwards while down, stride 32.4 mm. Control: making ANY of the 13 links 10% longer deforms the curve or locks the leg (h +10%: stance drops to 26%).

  • Walking: over 360 crank positions at least 2 feet are down on each side, the body height varies 0.04 mm and the centre of mass (computed from the real parts) stays at least 13.0 mm inside the support polygon. Control: all six cranks in phase -> fewer than 2 feet per side in 50 of 360 positions, the body drops 1.1 mm and the centre of mass leaves the support polygon.

  • Collisions: the layer layout (4 link layers per module) was searched and checked in the plane at 36 and 360 positions: links on the same layer stay ≥ 1.46 mm apart and anything crossing a foreign pin passes ≥ 1.73 mm from its boss. Controls: a link on the wrong layer collides; giving the rear leg its own crank pin 90° or 180° out of phase gives 28 and 24 collisions.

  • Real 3D assembly at 36 positions: 4020 nearby part pairs and all 66 pins with their heads, intersection volume 0. Every pin, thickened by 0.30 mm, passes through all 180 of its holes without touching (so the holes line up in the real pose); controls: a Ø2.0 hole or a pin 0.5 mm off would not fit. The pre-assembled rear leg slides in without hitting the front leg.

  • The frame, crank and journals stay ≥ 19.3 mm above the floor; only the feet touch it. Every part passes a layer-by-layer 45° overhang check (no supports), colour inlays survive a 0.4 mm feature test and never overlap; the three plates fit 175 × 175 mm.

About this design

Designed with AI assistance and checked in code before release (see above). Pictures are 3D renders and the slicer preview, not photos. Not printed yet: makes and feedback are very welcome.

Español

Mini Strandbeest de 12 patas con el mecanismo de Theo Jansen (sus "números sagrados" a escala 0,5): giras la manivela y camina, 67.6 mm por vuelta. El pie apoya en un tramo casi recto (52.1 % del ciclo a menos de 1 mm), siempre hay al menos 2 pies en el suelo por lado y el cuerpo no cabecea. 72 eslabones planos, ejes de filamento de 1,75 mm con holgura de 0,30 mm, montaje comprobado en 3D en 36 posiciones. 3 placas, 7 h 52 min, 123 g, sin soportes, AMS de 4 colores.

العربية

نسخة صغيرة من "ستراندبيست" بـ12 ساقا وفق آلية ثيو يانسن (أرقامه "المقدسة" بنصف الحجم): أدر المقبض فيمشي 67.6 مم في كل دورة. تلامس القدم الأرض في مسار شبه مستقيم (52.1٪ من الدورة)، ويبقى دائما قدمان على الأقل على الأرض في كل جانب. 72 قطعة مسطحة ومحاور من خيط 1.75 مم بخلوص 0.30 مم، وتم التحقق من التركيب ثلاثي الأبعاد في 36 وضعا. ثلاث صفائح طباعة، بدون دعامات، بأربعة ألوان.

Tags