Clothes dryer connector - JUWEL Fashion Dry
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Replacement hinge joint for JUWEL Fashion Dry clothes dryer. Fits Ø25 mm tubes, M6 bolt. Print bolt-head + nut part.
- Rating
- 0 / 5
- Likes
- 6
- Downloads
- 6
- Makes
- 0
- Views
- 40
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other House Equipment
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Náhradní kloubová spojka pro stojanový sušák na prádlo JUWEL Fashion Dry (Artweger / Juwel), na hliníkové trubky Ø25 mm. Dva tištěné díly a šroub M6 nahradí prasklý originální kloub – oprava sušáku místo vyhození.
Nastavení tisku
Tiskárna: Prusa Core One, tryska 0,4 mm (HF)
Materiál: Prusament ASA, tiskový profil Prusament ASA
Výška vrstvy: 0,15 mm (profil 0.15mm STRUCTURAL)
Výplň: 100 % – nejvíc namáhaný je krk hrdla u kloubu
Stěny: 5–6 perimetrů
Podpěry a límec: podpěry jen malované pod kloubem, límec zapnutý
Orientace: nastojato – hrdlem nahoru, kloubem (zuby) dolů k podložce
⚠ Orientace a podpěry: STL je uložené naležato – před tiskem díl postav hrdlem nahoru. Pak nastav Podpěry: Pouze pro vynucené podpěry (EN: Supports: For support enforcers only) a nástrojem Malování podpěr (EN: Paint-on supports, klávesa L) natři jen spodek kloubu. Hrdlo se tak tiskne bez podpěr a otvor zůstane kulatý. Přiložený bgcode má vše nastavené.
Čas a materiál (1 sada = 2 díly): 3 h 41 min, 46,5 g.
Filamenty
Oba díly: ASA, Prusament (Prusa Research). ASA snese slunce i vlhko na balkoně lépe než PLA.
Soubory
JUWEL_Fashion_Dry_hinge_v8_head.stl – díl se zahloubením Ø12 mm pro hlavu šroubu. Tisknout 1×.
JUWEL_Fashion_Dry_hinge_v8_nut.stl – díl s šestihrannou kapsou pro matici M6 (10,2 mm na klíč, hloubka 4,5 mm). Tisknout 1×.
JUWEL_Fashion_Dry_hinge_v8_0.4n_0.15mm_ASA_COREONE_3h40m.bgcode – hotový tiskový soubor pro Core One, oba díly na jedné podložce.
Jak je spojka vymyšlená
Proč vznikla: originální plastová spojka praskla v hrdle na trubku (asi těžké trenky) – slabé místo s tenkým žebrováním. Náhradní díl k sehnání nebyl, tak jsme rozbitý kus přeměřili šuplerou a navrhli nový.
Kloub: dva díly do sebe zapadají střídavými zuby (A-B-A-B) a drží je šroub M6.
Doraz v ose: oproti originálu se kloub v rozložené poloze opře, takže se neprolomí přes 180°.
Rozměry: trubka Ø25 mm, vnitřní průměr hrdla 25,3 mm, vnější 29,4 mm, šířka kloubu cca 29,5 mm, otvor 6,4 mm pro šroub M6.
Vyzkoušeno: verze v7 na sušáku (nasazení, chod, pevnost), v8 přidává doraz a menší vůli zubů.
Montáž
Nasazení: trubku lehce nahřej (horkovzdušnou pistolí nebo horkou vodou) a nasuň trubku. Uložení je záměrně těsné – po vychladnutí drží pevně.
Zuby dolů: jen tak se kloub při složení správně zarazí.
Díly nejsou zaměnitelné: při zubech dolů je díl pro hlavu šroubu vlevo a díl pro matici vpravo (pohled zespodu).
Šroub: M6 (cca 35 mm) s maticí, utáhnout jen tak, aby se kloub hladce otáčel. Matici případně zajisti lepidlem na závity.
Pojistný šroubek: originál ho měl v jednom hrdle, v modelu není – kdo ho potřebuje, provrtá si otvor.
Jiný sušák nebo průměr trubky? Napiš do komentářů typ sušáku a průměr trubky, případně nahraj Make s fotkou z balkonu. Další varianty vzniknou podle zájmu. Jde o neoficiální díl, bez vazby na JUWEL / Artweger.
English version
Replacement hinge joint for the JUWEL Fashion Dry freestanding clothes dryer (Artweger / Juwel), for Ø25 mm aluminium tubes. Two printed parts and an M6 bolt replace the cracked original hinge – repair the dryer instead of throwing it away.
Print settings
Printer: Prusa Core One, 0.4 mm nozzle (HF)
Material: Prusament ASA, print profile Prusament ASA
Layer height: 0.15 mm (0.15mm STRUCTURAL profile)
Infill: 100 % – the socket neck at the hinge takes the most load
Walls: 5–6 perimeters
Supports and brim: painted supports under the hinge only, brim on
Orientation: upright – socket opening up, hinge (teeth) down towards the bed
⚠ Orientation and supports: the STL is stored lying flat – stand the part upright before slicing. Then set Supports: For support enforcers only and use Paint-on supports (key L) on the underside of the hinge only. The socket then prints without supports and the bore stays round. The attached bgcode has everything set.
Time and material (1 set = 2 parts): 3 h 41 min, 46.5 g.
Filaments
Both parts: ASA, Prusament (Prusa Research). ASA handles sun and humidity on a balcony better than PLA.
Files
JUWEL_Fashion_Dry_hinge_v8_head.stl – part with a Ø12 mm counterbore for the bolt head. Print 1×.
JUWEL_Fashion_Dry_hinge_v8_nut.stl – part with a hex pocket for an M6 nut (10.2 mm across flats, 4.5 mm deep). Print 1×.
JUWEL_Fashion_Dry_hinge_v8_0.4n_0.15mm_ASA_COREONE_3h40m.bgcode – ready print file for Core One, both parts on one plate.
Design
Why it exists: the original plastic joint cracked at the tube socket (probably heavy underwear) – a weak spot with thin ribbing. No spare part was available, so we measured the broken one with calipers and designed a new one.
Hinge: the two parts interlock with alternating teeth (A-B-A-B) and are held by an M6 bolt.
End stop: unlike the original, the hinge rests against a stop when unfolded, so it cannot bend past 180°.
Dimensions: tube Ø25 mm, socket bore 25.3 mm, socket outer diameter 29.4 mm, hinge width approx. 29.5 mm, 6.4 mm hole for an M6 bolt.
Tested: version v7 on the dryer (fit, movement, strength); v8 adds the end stop and less play between the teeth.
Assembly
Fitting: gently warm the tube (heat gun or hot water) and push it onto the part. The fit is tight on purpose – once cooled, it holds firmly.
Teeth down: only then does the joint stop correctly when folded.
Parts are not interchangeable: with the teeth down, the bolt-head part goes on the left and the nut part on the right (bottom view).
Bolt: M6 (approx. 35 mm) with a nut, tighten just enough for the joint to move smoothly. Optionally secure the nut with threadlocker.
Locking screw: the original had one in one socket; it is not modelled – drill a hole if you need it.
Different dryer or tube diameter? Tell us your dryer model and tube diameter in the comments, or post a Make with a photo. More variants will follow based on interest. This is an unofficial part, not affiliated with JUWEL / Artweger.
Deutsch (kurz)
Ersatz-Gelenkverbinder für den Wäscheständer JUWEL Fashion Dry (Artweger / Juwel), für Alurohre Ø25 mm. Zwei gedruckte Teile und eine Schraube M6 ersetzen das gebrochene Originalgelenk, mit Anschlag in der ausgeklappten Stellung. Druck stehend, Muffe nach oben, Stützen nur unter dem Gelenk (Prusa Core One, Prusament ASA, fertige bgcode-Datei und STL). Inoffizielles Teil, ohne Verbindung zu JUWEL / Artweger.
Designed by 3D Rebels, Prague – 3drebels.cz