2,502 models
This clip was design to fix/repair/secure the broken or loose tab of a RJ45 Ethernet connector and avoid crimping. Designed to prevent from moving, wiggling, falling from the connector and easy to install. UPDATE 27/01/2021 Added the 3…
Print approx. €0.22–€0.27 excl. taxPreliminary estimate for one variant
The charging cable always breaks at the same position, just right under the plug. Don't replace it, Repair it with this easy print! This works for Apple USBC and lightning, as well as for samsung charging cables! No glue or tape is…
Print approx. €0.04–€0.05 excl. taxPreliminary estimate for one variant
You can put them on the handlebars in the normal position and turn the bicycle afterwards. They are designed for the handlebar with a diameter of 23 mm . I printed them with 4 perimeters, 15% honeycomb infill, without top and bottom…
Print approx. €5.27–€6.44 excl. taxPreliminary estimate for PETGSource material: PET
Ethernet cable fix which prints WITHOUT SUPPORTS. The layer line orientation aids in keeping the cable in the port. Print settings: layer height 0.2mm 3 thick walls Infill: Does not matter since the piece is too small to even have infill…
Print approx. €0.11–€0.14 excl. taxPreliminary estimate for one variant
Swan, with a small support built in to hold the nose without any extra supports needed
Print approx. €3.87–€4.74 excl. taxPreliminary estimate for PETGSource material: PET
This is a repair clip for your broken Ethernetcable. You can easy print it. The clip makes it possible that the cable does not always slip out so easily when the clip is broken off at the top. To print: you can use PLA too Use supports
Print approx. €0.25–€0.31 excl. taxPreliminary estimate for PETGSource material: PET
A little support is needed but comes off quite easy
Print approx. €2.93–€3.58 excl. taxPreliminary estimate for PETGSource material: PET
Easily 3D Printed tool that is used to remove adhesive between two parts that have tight tolerances between them and are fragile. Most commonly used when removing touch screen from an phone or tablet. IF YOU HAVE A RESIN 3D PRINTER I…
Print approx. €0.18–€0.22 excl. taxPreliminary estimate for PETGSource material: PET
All-in-one Repair Kit for a Broken Flush Mechanism. Straight and Angled Levers included. American Standard. No Supports! Higher Infill on Lever Arm Recommended. Assembly Order: Bolt (Cut-out towards the Chain) Nut (Counterclockwise…
Print approx. €1.92–€2.35 excl. taxPreliminary estimate for one variant
What is it? Printed part to connect the particleboard floor of a drawer to its chipboard backpanel. Tested with a repair and enhancement on my 2012 IKEA MALM chest's drawers. Might work for others with the same design too. Why use it?…
Print approx. €0.15–€0.18 excl. taxPreliminary estimate for PETGSource material: PET
Zip-Tie Garden Hose Coupler | 16mm Water Line Connector This simple yet effective 3D printed connector lets you quickly join two 16mm diameter garden hoses without specialized tools or fittings. Perfect for extending your watering reach…
Print approx. €0.24–€0.29 excl. taxPreliminary estimate for PETGSource material: PET
An ethernet RJ45 repair clip with a working snap lock that locks the plug in the socket. Prints without supports added from the slicer thus it prints quicker and and uses less material. NOTE: Needs to be printed with 3 perimeters (3…
Print approx. €0.11–€0.13 excl. taxPreliminary estimate for one variant
Quick fix for RJ45 plugs whose little clip broke off. Because there are so many variations of RJ45 plugs and every one needs a different version of this model, I uploaded a .STEP file and an editable Fusion 360 file where all the…
Print approx. €0.10–€0.13 excl. taxPreliminary estimate for PETGSource material: PET
Since commercally available bicycle repair stands are quite expensive, I decided to design one on my own. This assembly stand is supposed to hold your bike in a comfortable position, while you can work on it. I used 53mm pipes and did a…
Print approx. €1.58–€1.93 excl. taxPreliminary estimate for PETGSource material: PET
Modification of the model by Plutho to accommodate two instead of three AA batteries. This model may need to be customized as needed.
Print approx. €1.81–€2.21 excl. taxPreliminary estimate for PETGSource material: PET
Quick repair of the outer shell of the fitlok, 4 are included in the print just to fast track prototyping. Remove as needed. I printed at 105% and it was a snug fit. v1 lasted from Nov to May, made a v2, and now that my printer is…
Print approx. €0.36–€0.44 excl. taxPreliminary estimate for PETGSource material: PET
This is a large, useful toolbox for small tools and parts. I use it for repairing my 3D printers because of all the small parts and tools needed. I have several printers that are used a lot. Anyone that really puts their printer to good…
Print approx. €4.37–€5.34 excl. taxPreliminary estimate for one variant
While you are staying safe at home, you might have something break that you'd typically go buy a replacement or perhaps a repair bracket for. (For example, the snack drawer's increased contents and enthusiastic children might result in…
Print approx. €0.44–€0.54 excl. taxPreliminary estimate for PETGSource material: PET
An RFID chip repair case is a practical accessory designed to address common issues with RFID chips. When a new RFID chip is inexpensive but new one may encounter registration problems, this case offers an alternative. If the side cover…
Print approx. €0.49–€0.60 excl. taxPreliminary estimate for one variant
Creating a spacer for an M3 screw Spacer for large screw hole Easy and fast printing Printing: Material: PETG Supports: no Orientation: can be printed from both sides
Print approx. €0.04–€0.04 excl. taxPreliminary estimate for PETGSource material: PET
You can use these clamps when repairing for instance an iPad screen and you need to clamp the edges while the glue sets. I recommend using automatic support painting on the C part of the clamp and using organic supports. When printing in…
Print approx. €2.16–€2.64 excl. taxPreliminary estimate for one variant
An ethernet RJ45 repair clip with a snap lock that locks the plug in the socket. This model is optimized for sideways print so that the snap lock prints with the layer lines to increase the strength. Use: 3 perimeters (walls) supports To…
Print approx. €0.14–€0.17 excl. taxPreliminary estimate for one variant
Automatic Feeder (SureFeed MPF001) of family member couldn't open lid anymore, as a result their cat couldn't get to prescription kibble. Turned out only a small part was broken, quickly modeled and printed this fast and tiny replacement…
Print approx. €0.12–€0.14 excl. taxPreliminary estimate for one variant
Slider repair kit Fits: DT 790 / DT 797 DT 770 / DT 770 PRO / DT 770 PRO HT DT 880 / DT 880 PRO / DT 880 PRO HT DT 990 / DT 990 PRO HS 200 Dyn / HS 200 Rotor / HS 200 Trend HS 400 MMX 300 UPDATE - 30.10.2022: Some slight fine-tuning.…
Print approx. €0.75–€0.92 excl. taxPreliminary estimate for one variant
No more throwing away RJ45 Ethernet cable ends with a broken locking tab in the trash. Use this clip. Simply snap one of these clamps onto the broken plug and then slide it forward until it fits next to the base of the tab. A tab on these…
Print approx. €0.17–€0.21 excl. taxPreliminary estimate for PETGSource material: PET
This remix is for the standard handle bar diameter size of 22,2 mm. Perfect for working on your bike without scratching your handle bar or your bell. Makes it more stable as well. Print settings: Material: PETG, PLA might be too brittle…
Print approx. €3.37–€4.12 excl. taxPreliminary estimate for PETGSource material: PET
A simple way to organize your screws or parts while repairing.
Print approx. €0.60–€0.74 excl. taxPreliminary estimate for one variant
Quick fix for some 4 colors pens. It's mounted in force. I didn't make any thread. Some glue might be needed. Printed in PLA, 200 µ height.
Print approx. €0.37–€0.46 excl. taxPreliminary estimate for one variant
The mounts are designed for handlebars + handlebar tape with a diameter of 40mm and increased ground clearance. I printed whit PETG them with 4 perimeters, 10% honeycomb infill, without top and bottom layers.
Print approx. €2.36–€2.88 excl. taxPreliminary estimate for PETGSource material: PET
Both rings that support the headphone extension broke due to their flimsy design. The rings flexed and eventually failed under stress. I modeled the dimensions in Fusion 360 and designed a pair of clamp reinforcements. After installing…
Print approx. €0.25–€0.30 excl. taxPreliminary estimate for one variant
I had to repair our Kitchenaid mixer during lockdown with no access to a parts supplier. This little gear did the trick. The OEM part is nylon and designed to fail if overstressed, thereby saving the rest of the gear train. It's an easy…
Print approx. €0.97–€1.18 excl. taxPreliminary estimate for one variant
1.- Introduction As with all prints I do, all start or from a need, a fix or a lust-to-have. This model was designed as a fix for a broken heel in a sky boot from a good friend, that got deteriorated due to age and use. 2.- Design Process…
Print approx. €3.89–€4.75 excl. taxPreliminary estimate for PETGSource material: PET
Print two identical shells (there are four different lengths available) to repair your lightning connector. Before put both parts together use some silicone to fill this inside the two parts. Afterwards put your connector with both parts…
Print approx. €0.13–€0.15 excl. taxPreliminary estimate for PETGSource material: PET
2004-2005 Honda Civic Si EP3 parking brake trim parts. Original parts were a natural color plastic with chrome plating, which wore out. Then the plastic broke. I made these repair parts, and used plastic epoxy to glue the new trim part…
Print approx. €0.46–€0.56 excl. taxPreliminary estimate for one variant
Hello, I have a repair kit for IKEA, JYSK, Siko cabinet hinges for you. It is suitable if the screw seat in the wood is torn out. It fits perfectly on the hinges of the drivers on the cabinets , for example in the kitchen. It works great.…
Print approx. €0.41–€0.50 excl. taxPreliminary estimate for one variant
Better looking
Print approx. €1.21–€1.47 excl. taxPreliminary estimate for PETGSource material: PET
REPAIRED correct files loaded scaleable and easy to print
Print approx. €9.27–€11.32 excl. taxPreliminary estimate for one variant
Tired of having to throw away your jeans just because the button is ripping out of the fabric? No spare clothing on your business trips? Your children too enthusiastic in the playground? Went out of control in an all-you-can-eat…
Print approx. €0.32–€0.39 excl. taxPreliminary estimate for one variant
In our rotational Cutter from Tupperware the gear which transports the force to the knife's broke. So i designed it as close as possible to the original one. Fiirst i printed it in PLA but it not last for a very long time. So i decided to…
Print approx. €0.56–€0.69 excl. taxPreliminary estimate for one variant
Ever get your cloth patio umbrella too close to the porch light or the fire pit? This is a clip to capture the cloth and the umbrella spoke together. Simply pull the cloth down to the end of the spoke then clam shell it together with a…
Print approx. €4.32–€5.28 excl. taxPreliminary estimate for PETGSource material: PET
It is a waste of money (23 euro incl shipping) and material to buy a new drip tray, because it is only for the looks.
Print approx. €0.17–€0.20 excl. taxPreliminary estimate for one variant
A repair "kit" for USB-C plug casing. Depending on how much of the casing is missing, print “USB-C_cable_plug_repair_additional”. If only one side broke of then you can skip “USB-C_cable_plug_repair_additional”. Please also note the…
Print approx. €0.31–€0.38 excl. taxPreliminary estimate for PETGSource material: PET
The hook that holds the parcel tray broke and the parcel tray could no longer be raised. So I designed a fast and cheap solution. You only need to print ed place the 2 pieces. For a better fixing you could put some glue . DON'T PRINT IN…
Print approx. €0.27–€0.33 excl. taxPreliminary estimate for PETGSource material: PET
PYC3D.ES SOCIAL MEDIA MEMBERSHIPS PYC3D SHOP DONATE LIGHTNING CABLE REPAIR Print two identical shells to fix your lightning connector. Before assembling the parts, apply some glue to fill the inside of both pieces. Next, place your…
Print approx. €0.38–€0.46 excl. taxPreliminary estimate for one variant
I made my own Repair mat... Im not printed it yet, but i wanna to share with you guys. I will printed it with TPU Filamant. I hope u like it and enjoy my others stuff in my profile!
Print approx. €3.25–€3.97 excl. taxPreliminary estimate for one variant
Holden VY / VZ Centre Console Flip Lid repair TAB, This will also suit some US & exported models. Printed in ABS, 50% Honeycomb Infill, 0.15mm Layer height, Print 3 or 4 at once. Brim can be used if you have adhesion issues, These have…
Print approx. €0.41–€0.50 excl. taxPreliminary estimate for one variant
I created this model to remove the arm from a Ikea FRIDANS roller blind but the model may also be used to replace broken parts of common roller blinds. The mechanism is working quite well, if you are having issues please write a comment…
Print approx. €5.02–€6.14 excl. taxPreliminary estimate for PETGSource material: PET
Needed to fix my patio umbrella. Two of the arms broke after the wind knocked it over. Just needed to use some M5x35mm bolts with some washers and nuts. I used some nylon washers since it's supposed to be able to to articulate when…
Print approx. €1.77–€2.17 excl. taxPreliminary estimate for PETGSource material: PET
Repair kit for Philips SHP2500 headphones. To print all parts need to add in slicer mirrored part ( full kit in g-code file) Material: PET-G -recomended Layer high: 0,2 or lower Supports needed under the cylidrical parts ( support added…
Print approx. €3.77–€4.60 excl. taxPreliminary estimate for PETGSource material: PET
Here we'll see how 3D printing can be used to repair a cabrio rooftop for few Euro cents On my Volvo C70 convertible, the roof sky is bent and unfolded by a complex system of strings that are hung at specific locations on the roof sky via…
Print approx. €0.17–€0.21 excl. taxPreliminary estimate for PETGSource material: PET
Vor- und Nachteile auf einen Blick: + verbindung oder verlängerung von GT2 6 mm Zahnriemen + schmarl/klein/minimalistisch + Druckerfreundlich (Überhänge >55°, keine Brücken, etc.) + wiederverwendung von defekten Zahnriemen Einkaufsliste:…
Print approx. €0.33–€0.40 excl. taxPreliminary estimate for one variant
Weight plates for blinds sometimes become brittle and break when removed from the connecting chain. Several popular repair solutions ( https://www.printables.com/model/147266-89-mm-lysel-slatted-curtainvertical-blinds-weight ) suggest…
Print approx. €0.22–€0.27 excl. taxPreliminary estimate for PETGSource material: PET
My Print Parameters: Resolution: 0.2 Nozzle: 0.4 Seam position: Aligned Infill: 15% Top Layers: 6 Bottom Layers: 5 Perimeters: 2 Rafts: No Supports: No Material: PETG Prusament Signal White/Lipstick Red, Urban Grey Happy printing!
Print approx. €0.18–€0.22 excl. taxPreliminary estimate for PETGSource material: PET
The Ikea Parik is a really good chair, firm pre-formed foam and comfortable to sit on. We bought nine of them second hand for little. The legs have a foot that can move around a ball at the end of the leg. One of the chairs missed the…
Print approx. €0.45–€0.55 excl. taxPreliminary estimate for PETGSource material: PET
Screw sorting system for phone repair, it can be used, for example, when disassembling a phone to determine the mobile phone disassembly procedure. I printed it from two colors and I think it is better than from one. the size of one…
Print approx. €1.29–€1.58 excl. taxPreliminary estimate for one variant
EN Repair of scissor handles two models, : one for small and one for large scissors Print out the necessary template Heat the handle sufficiently (80-90°c) to seal it into the handle. Do not overheat, try several times to find the right…
Print approx. €0.73–€0.89 excl. taxPreliminary estimate for one variant
Designed for my wife who broke her RFID keychain. First, you need to get the chip out of the damaged keychain. Then hold the print in the right place and place the chip in the print. Resume the print.
Print approx. €0.20–€0.24 excl. taxPreliminary estimate for PETGSource material: PET
Small parts tray for Feedback Sports Pro-Elite bike repair stand As I have enough storage space / room in the workshop (workbench etc.), I didn't need a large tray for the assembly stand. The holder is sufficient for valve caps, disc…
Print approx. €7.91–€9.66 excl. taxPreliminary estimate for PETGSource material: PET
Forced to stay at home we cook more. I recycled an old pan. The lid handle was broken and full of mold. The usual lid handle has the problem that water accumulates in it. This is a wonderful place to incubate germs. The producers have not…
Print approx. €1.36–€1.67 excl. taxPreliminary estimate for PETGSource material: PET
print with at least 6 walls
Print approx. €1.17–€1.43 excl. taxPreliminary estimate for one variant
Exactly like the original model ( https://www.thingiverse.com/thing:2803664 ), but I've repaired it and split into 2 parts (otherwise slicer splitting could fail, etc…)
Print approx. €0.56–€0.69 excl. taxPreliminary estimate for PETGSource material: PET
this is a template piece to fit onto the end of a broken Tesla mobile charger. I have included the template piece and the STL piece that I used to repair mine. The use of “J-B Weld 50139 Plastic Bonder Body Panel Adhesive and Gap Filler…
Print approx. €1.21–€1.48 excl. taxPreliminary estimate for PETGSource material: PET
Clip to replace a broken one on your dryer horse with 15mm inner diameter rods. Print two halved pieces that join when forced into the rod. No supports needed due to half cut design.
Print approx. €0.51–€0.63 excl. taxPreliminary estimate for PETGSource material: PET
This is a repair for a Ford Transit headlight housing. Housing arrived with a broken tab and instead of returning, crafted a repair. This was on an upgraded Ford headlight (projector beam) on a Storyteller Camper Van. Printed in ABS and…
Print approx. €0.50–€0.61 excl. taxPreliminary estimate for one variant
The handle of a pool skimmer basket is broken. It breaks at the end that fits into the basket. The plastic must be poorly resistant to the aggression of salt-treated water over time. The handle is rigid and it is by distorting the basket…
Print approx. €0.57–€0.70 excl. taxPreliminary estimate for PETGSource material: PET
With this thing you can rapair your broken protective rubber sleeve on the Beyerdynamic MMX 300 headset cable. You have to print the part twice. To open the earpiece you hav to do a few easy steps. Remove the earpiece cushion, than you…
Print approx. €0.17–€0.21 excl. taxPreliminary estimate for one variant
This little model can fix the 10327 Arteides Royal Ornithopter's wing when you mount it on the wall. I'd recommend to use my other design:) https://www.printables.com/model/1176134-lego-10327-arteides-royal-ornithopter-wall-mount
Print approx. €0.59–€0.73 excl. taxPreliminary estimate for one variant
This is the little bridging element of the front panel from the Fritz!fon C5. Settings Value Infill 25% (adaptive cubic) Perimeters 2 Layer Height 0.10 mm Structural Material PETG / PLA Supporting Material none Comments printed on MK4S…
Print approx. €0.06–€0.07 excl. taxPreliminary estimate for one variant
I had only used my Igloo Portable Ice Maker for a little less than a year before it gave out. I came home one day and it had just stopped working. I searched the ‘net for answers, and finding few, decided to just tear the machine down and…
Print approx. €0.15–€0.18 excl. taxPreliminary estimate for PETGSource material: PET
Roof/Railing Patch -Repair _____________________________________________________________________________________________ This Customizable patch can repair your broken corrugated roof or railing. You can set your own dimensions with FCStd…
Print approx. €3.10–€3.79 excl. taxPreliminary estimate for PETGSource material: PET
My wife has these humming bird feeders around the house. Sometimes the top plastic piece used to hang it up breaks. This print fixes that. Break off the little tabs on the feeder top where the plastic split, print this part, unscrew the…
Print approx. €0.34–€0.42 excl. taxPreliminary estimate for one variant
We have a few Tommy Bahama Beach chairs and after many years the plastic part that connects the chair frame and allow for the chair to fold broke at the main junction. The challenge was to create an ASA 3D printable part that can take the…
Print approx. €6.36–€7.78 excl. taxPreliminary estimate for one variant
This part is for this particular water bottle that is sold online and in stores in North America: “Zak Designs Minecraft 18/8 Single Wall Stainless Steel Kids Water Bottle with Flip-up Straw Spout” No doubt, there is probably…
Print approx. €0.25–€0.30 excl. taxPreliminary estimate for PETGSource material: PET
The wings and hook are completely my own design as they were missing from the wreck. Made some modifications to the undercarriage to make it more durable.
Print approx. €3.54–€4.33 excl. taxPreliminary estimate for PETGSource material: PET
The brackets of the cable routing got brittle so I decided to redesign and 3d print them. Now my retro garrett headphones are like nw. You can re-use the screws and nuts. More infos on my blog:…
Print approx. €0.80–€0.98 excl. taxPreliminary estimate for PETGSource material: PET
TL;DR A broken plastic part with less than 1 g has been redesigned and 3D-printed, thus avoiding 975g of garbage in the form of a defunct mixer. Machine to repair Our Siemens hand mixer MQ90001/02 broke about 3 years ago. Thanks to the…
Print approx. €0.15–€0.18 excl. taxPreliminary estimate for one variant
This print fits Park Tool PRS-2 & PRS-3 Repair Stands with a 44.25mm (as measured) column. With an interior print of 44.5mm the press fit design has enough friction to stay in place without hardware. It has space for the following items:…
Print approx. €13.47–€16.46 excl. taxPreliminary estimate for PETGSource material: PET
Commonly failing plastic components in motorhome window blinds can be a persistent issue. This repair kit provides a durable, 3D printable solution to replace worn or broken parts, restoring full functionality to your blind system.…
Print approx. €0.95–€1.16 excl. taxPreliminary estimate for PETGSource material: PET
I used this parametrizable model in order to fix some tip toi ringbooks after the cover has been detached from the rings. The two halfs slide in from above and below. Afterwards i glued them onto the cover with some superglue and secured…
Print approx. €0.09–€0.11 excl. taxPreliminary estimate for one variant
The seat adjustment knob on my 2015 Toyota Tacoma broke off. Glue wouldn't work so I designed a ring to reinforce the broken gears and an inner part that spins to hopefully provide more bite to the inner shaft of the seat. I used an M4X20…
Print approx. €0.37–€0.45 excl. taxPreliminary estimate for PETGSource material: PET
This is a simple sign for machines or equipment under maintenance to help with LOTO (Lock Out, Tag Out) so that it can be seen the machine cannot be used, and also, the person responsible for the operation. As you will need to change the…
Print approx. €1.03–€1.25 excl. taxPreliminary estimate for one variant
Summary This is a cable cover for “Logicool M125” mouse to cover the exposed part of the wire. Build info No support is required . It can be printed from PLA . It consists of two parts, and the mechanism is to fit the cylinder of the…
Print approx. €0.06–€0.07 excl. taxPreliminary estimate for one variant
The clip is reinforced to avoid the joint get broken again. Print instruction: Material: PETG recommended Supports: partial required - organic support recommended Enclosure: not required The clip is suitable for e.g. LED Christmas candles…
Print approx. €0.24–€0.30 excl. taxPreliminary estimate for PETGSource material: PET
This print fits Park Tool PRS-2 & PRS-3 Repair Stands with a 44.25mm (as measured) column. With an interior print of 44.5mm the press fit design has enough friction to stay in place without hardware. It has space for the following items:…
Print approx. €13.47–€16.46 excl. taxPreliminary estimate for PETGSource material: PET
The clamps holding my 25 odd years old Klick fix attachment to the handlebar broke. I found it was quite easy to print a replacement. Print with PETG, flat on the bed. Use roughly 6 perimeters to make it strong.
Print approx. €0.61–€0.75 excl. taxPreliminary estimate for PETGSource material: PET
During replacing of the batteries of the hue dimmer switch V1 the very weak strip of the main housing was brocken. Because of that, the battery cover does not mount anymore in the right way. With this part the problem is solved. Während…
Print approx. €0.06–€0.07 excl. taxPreliminary estimate for PETGSource material: PET
I got this excavator (e.g. https://www.cat-fahrerclub.de/de/kinder/bruder-mobilbagger.htm) for repair, the handle was broken off and the shovel was missing. To replace the handle, the middle arm needs to be opened by carefully unsnapping…
Print approx. €0.67–€0.82 excl. taxPreliminary estimate for one variant
Small print part for a missing piece
Print approx. €0.17–€0.21 excl. taxPreliminary estimate for PETGSource material: PET
EN: Yesterday, the connection piece of the hose of the above-mentioned blood pressure measuring device broke off. A replacement was needed. Here is the result. It works. Could be that it also fits other devices. The inner diameter…
Print approx. €0.13–€0.16 excl. taxPreliminary estimate for one variant
One of the brackets on my sunglasses had broken after someone sat on them.. Needed a repair so made these models to print. After printing, it is advisable to sand the sunglass bracket nice and even to make it feel more comfortable. Remove…
Print approx. €0.87–€1.07 excl. taxPreliminary estimate for one variant
print with 100% infill out of something as strong as PETG or stronger… these are made to break but we have gotten more time from the printed replacements than the original part. Brim is a must, its a small part with a small footprint.…
Print approx. €0.33–€0.40 excl. taxPreliminary estimate for PETGSource material: PET
We dropped the machine and the end of the hose was broken as can be seen in the photo. This cap fits on snug so that the silicon seals the hose air tight.
Print approx. €0.19–€0.24 excl. taxPreliminary estimate for one variant
Steer Tube Cork for Fox 36 with Storage for this tubeless repair kit: https://www.amazon.de/gp/product/B097GCH7H8/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 The repair kit and the cork must fit tightly so that they do not loosen on…
Print approx. €0.92–€1.12 excl. taxPreliminary estimate for one variant
The part is printed with PETG. Print instruction: supports: YES | default setting recommended layer height: 0,2mm nozzle diameter: 0,4mm brim: YES (recommended to ensure good adhesion on the print bed) enclosure: NO Assembly instruction:…
Print approx. €0.51–€0.63 excl. taxPreliminary estimate for PETGSource material: PET
This model contains two parts - one is the motor yoke to hold the motor, and the other is an insert (print in TPU) that provides some grip and shock transmission. My West Marine transom saver had fallen down and dragged the road - and the…
Print approx. €9.95–€12.16 excl. taxPreliminary estimate for PETGSource material: PET
This is a simple, yet effective repair piece designed to fix broken foldable clothes drying racks. When one of the welded joints on my drying rack broke, I created this bracket to restore functionality and extend the life of the rack…
Print approx. €0.07–€0.09 excl. taxPreliminary estimate for one variant
Erleichtert die Reparatur von Radios und das lästige Umdrehen. Scheiben und Füße "müssen" in TPU gedruckt werden, alles andere in PETG. Mit Scheiben aus PETG, PLA usw lassen sich die Arme mangels Friktion auch mit Gewalt nicht festklemmen…
Print approx. €4.25–€5.20 excl. taxPreliminary estimate for PETGSource material: PET
With time the wheels of my Craftman lawn mower came loose and got out even if the bolt is in place. The wheel hole now has a conical shape and the back of the wheel is worn too. With those 2 parts no need to change the wheel. The flange…
Print approx. €0.20–€0.24 excl. taxPreliminary estimate for PETGSource material: PET
This repair module for the Sigma ROX bike computer can be glued onto the device if the tabs of the quarter-turn mount are broken. Tested with Sigma ROX 4, but should be compatible with ROX 2,7,11,12. Please comment if you have tested it…
Print approx. €0.44–€0.53 excl. taxPreliminary estimate for one variant
Repair of the shower door drive I recommend printing from ABS or ASA. Considering its properties. Print with 0.6 nozzle and 0.4 layer height
Print approx. €0.67–€0.81 excl. taxPreliminary estimate for one variant
![Cable Repair and Protect for iPhone and Samsung [lightning+usbc]](https://media.printables.com/media/prints/590112/images/4827822_b916b887-676b-4723-b0c9-90881c40951e_31bb8182-a7ba-4745-adfd-b9d44646baac/195cfe9b-40fc-4570-b695-c540798fc979.jpeg)
