QRP Labs QMX+ CW Kneeboard with Tilted Cradle, Paddle Mount and Storage
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Kneeboard for the QRP Labs QMX+: tilted cradle, magnetic paddle tab, shock cord hold-down, hidden storage.
- Rating
- 0 / 5
- Likes
- 6
- Downloads
- 12
- Makes
- 0
- Views
- 246
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Electronics
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Overview
A one-piece kneeboard for the QRP Labs QMX+ transceiver. The radio sits on an incline toward you, so the display faces up at you instead of out at your belly. A 2 in steel fender washer in the front tab holds a magnetic-base paddle. Two shock cords hold the radio down. A snap-in lid closes off a storage compartment under the radio.
On the Air
Built for portable CW: POTA, SOTA, or a picnic table, with the board strapped to your thigh. The QMX+ weighs 578 g and sits upright with its front panel toward you. The tilt makes the LCD readable from above, and the radio slides back against the rear corner guides on its own, so both hands are free to hook the cords. The Ear and Mic/Paddle jacks on the front panel stay clear: with straight plugs, the plugs pass over a typical paddle. The board ends at the rear panel, so the BNC, USB-C and DC plugs hang free and stay off your leg. The compartment under the radio is big enough for earbuds, a spare paddle cable, spare shock cord, or a pencil and a folded log sheet.
Print Settings
Printer: Bambu Lab X2D, 0.4 mm nozzle
Material: PETG/PCTG. (Not PLA)
Layer height: 0.2 mm (or adaptive)
Walls: 4. Top and bottom layers: 5.
Infill: 15 to 20% gyroid
Supports: none
Orientation: board underside down, lid flat with the text up
Hardware and Assembly
1x 2 in (50.8 mm) steel fender washer, about 1.3 mm thick - https://a.co/d/0h5xek8Y
2x 3 mm shock cord, about 370 mm and 335 mm including knots (add about 10 mm each if your QMX+ has its stick-on feet) - https://a.co/d/0dVShHDw
1x 38 mm (1.5 in) elastic leg strap - https://a.co/d/00KF84nI
Adhesive for the washer (CA or epoxy)
Glue the washer into the round pocket on the front tab.
Thread the strap down through one wing slot, under the board, and up through the other. The strap wraps the outer bar of each slot.
For each cord, tie a stopper knot and pull it into the plain hole on the left wing so the knot sits in the recess underneath.
Set the radio in the cradle, front panel toward you. It drops between the corner guides and rests on the ledge.
Bring each cord over the top of the case, down through the matching keyhole on the right wing, and tie a knot underneath to set the tension.
To remove the radio, squeeze each cord out through its keyhole slit. The knots stay tied, so the tension stays set.
To use the storage, lift the radio out and pull the lid up by its finger slot. Press the lid down until it clicks into place.
Design Notes
Feet or no feet: the radio sits on a 5 mm ledge around its edge, so the stick-on feet can be anywhere, or missing. Side and end clearance stay fixed. The 15 mm corner guides grip 15 mm of the case without feet and 10 mm with them. The cords take up the 5 mm difference. The lid sits 6 mm below the radio's bottom so feet never touch it.
Makes, remixes and fit reports from other QMX+ owners are welcome.