Counting matching models…
I made this to adapt an old speaker/mic to my QMX. The spacing between the 3.5mm audio plugs is 12mm. It will only plug in one way because the other way the power cable will block it. The 3.5mm plugs I used have 7.9mm ends which depending…
UPDATED 7/15/2026: Now on V3, reduced outer wall height by another 0.2mm as one person who printed V2 had the knob hit the case before the button press registered. I also drew up a small .6mm tall shim so if you fit the knob and find it…
This redesigned QMX case focuses on maximum weight reduction and rigidity, offering a 33% weight saving over the original aluminum housing and knobs. Assembly Hardware Screws: All versions require M3-0.5 x 10mm black nylon flat head…
Features Waterproof Variable size of the rear box Five quick-release mount points on the body of the box, another on the rear box (if it is deeper than 80mm) suitable for example for mounting on a camera tripod - the screw is part of the…
UPDATED 7/15/2026: Now on V3, reduced outer wall height by another 0.2mm as one person who printed V2 had the knob hit the case before the button press registered. I also drew up a small .6mm tall shim so if you fit the knob and find it…
This is a 3S battery pack for the QRP Labs QMX Transceiver. It holds 3x Li-ion packs I purchased from Amazon. It also includes rails to protect the front panel knobs. If I don't count the rails, the battery pack only adds 8mm to the…
Original description: "Simplified/free version of my case for QRPLabs QMX+ Case has slightly biger tolerances but precise soldering of front and back components is still needed. You can always drill the holes a bit if you mised position…
After making the original, I was unhappy with the lack of structure to prevent the QMX from sliding out of the cover, so I tweaked the design a bit to add gussets on the end and increase clamping force which prevents the QMX from sliding…
Simple cover to protect the rotary encoders and buttons on a QMX when in a pack. This version is for the original factory knobs. Print the main model by itself for a minimal cover or 2 of the round pieces and glue them to the main model…
Simple minimal thickness cover to protect the rotary encoders and buttons on a QMX when in a pack. The four 10mm magnets can be 1.6mm-2mm thick. The knobs are slightly modified versions of the KF0ARE QMX knobs here on Printables. I added…
After using my QMX+ at home and in the field, I decided I did not like the viewing angle of the transceiver while it was sitting on the table. This stand is designed to raise the front of the transceiver and improve the viewing angle. Can…
QMX stand to raise the front for better viewing of the display and knobs when operating the radio. Btw.. my first ever 3D model made in Freecad
I didn't want to drill holes in my original cover, so I created a cover I could modify as I wanted.
Simplified/free version of my case for QRPLabs QMX+ Case has slightly biger tolerances but precise soldering of front and back components is still needed. You can always drill the holes a bit if you mised position on some of them. XY size…
A minimal set of covers for the QRP Labs QMX radio transceiver. The case is a little bit smaller than the QRP Labs metal case and about half the weight. Here is the same model on Makerworld for Bambu Lab printers . Bill of materials:…
Low profile knobs for the QRP Labs QMX radio transceiver. What problem does it address? The default knobs are quite tall and pointy and difficult to operate with just one finger. This provided model is easy to rotate with just a thumb on…
I made this to adapt an old speaker/mic to my QMX. The spacing between the 3.5mm audio plugs is 12mm. It will only plug in one way because the other way the power cable will block it. The 3.5mm plugs I used have 7.9mm ends which depending…
A slip fit case for the QRP Labs QMX to protect the knobs and screen during travel, and act as a stand to better angle the display when in use. Print Settings Printer Brand: Creality Printer: Ender-3 v2 **Rafts:** No Supports: No…
I realized no one had made a cover for the QMX+, so i made one. But i also made sure to include as much functionality as possible into it, making it both worth adding to the QMX+ but almost a necessary addition. This cover has a stand,…
A minimalist, press-fit cover for the popular QMX/QCX-Mini QRP transceivers produced by QRPLabs. Installs over the front of the radio to protect the screen, buttons, and knobs. When using the transceiver, the cover can be installed on the…
Small GPS dongle for the QMX to set time and Maidenhead. Items used: GPS used is a Beitian BE-280 with allows for 9600 bps and the 1Hz pulse. ( https://www.amazon.com/dp/B0BV6295F9 ) 3.5mm TRS jack ( https://www.amazon.com/dp/B09PFZ8XKP…
Very simple desktop stand for QMX / QCX-mini. Fixed 60-degree angle, only 2mm thick.
This is a generic mount for a QRP Guys QMX transceiver. I have purposely not added any specific screw holes or other features for attaching the mount to something. If you desire, you can add features to the generic mount to mate up with…
This is a remix of Adam Kimmerly's (K6ARK) QMX/QCX/QDX/(tr)uSDX knob. The original K6ARK knob is an excellent design, it is low profile, light weight and makes the tuning knob very easy to spin giving the QMX more of a full size desktop…
UPDATED 7/15/2026: Now on V3, reduced outer wall height by another 0.2mm as one person who printed V2 had the knob hit the case before the button press registered. I also drew up a small .6mm tall shim so if you fit the knob and find it…
This redesigned QMX case focuses on maximum weight reduction and rigidity, offering a 33% weight saving over the original aluminum housing and knobs. Assembly Hardware Screws: All versions require M3-0.5 x 10mm black nylon flat head…
I finally decided to publish this model, since its way too cool for not being out there. Be warned up front: Its a complicated print. For the Part "BAOFENG_Akkuhalter", you need to print with supports, and select a full support interface…
Jednoduchý držák s protiskluzovou vložkou z gumové vložky Ø 6mm. Tištěno z ABS
This is a case that holds the QRP LABS QMX, an INIU PD power bank and a Kanga transmatch ATU to make everything a little easier to setup. The holes on the side are for 4mm brass inserts for the key bracket and the hole at the front is for…
Features Waterproof Variable size of the rear box Five quick-release mount points on the body of the box, another on the rear box (if it is deeper than 80mm) suitable for example for mounting on a camera tripod - the screw is part of the…
UPDATED 7/15/2026: Now on V3, reduced outer wall height by another 0.2mm as one person who printed V2 had the knob hit the case before the button press registered. I also drew up a small .6mm tall shim so if you fit the knob and find it…
VE7ZAX QMX Speaker Easy quick speaker project for the QMX with enough volume for indoor and non-noisy SOTA/POTA use. I wanted a simple, tidy, clutter-free way to listen to my QMX without headphones so I whipped up the ear-popping menace.…
Simple and minimal clips for the QRP Labs QMX that let you use your Nitecore NB5000 Air power back as a stand making a tidy setup. Posting for the nine other people that have a QMX and a Nitecore NB5000 Air. Thanks for any likes and…
Designed to hold the radio on the right side and the battery below it. I held them both together with my wife's hairtie. Then the left side has three versions depending on what size notecard you want to use or to hold your phone. The…
This is a 3S battery pack for the QRP Labs QMX Transceiver. It holds 3x Li-ion packs I purchased from Amazon. It also includes rails to protect the front panel knobs. If I don't count the rails, the battery pack only adds 8mm to the…
Original description: "Simplified/free version of my case for QRPLabs QMX+ Case has slightly biger tolerances but precise soldering of front and back components is still needed. You can always drill the holes a bit if you mised position…
I printed this in PETG for flexibility of the tabs holding the Talentcell. First slide the QMX into the frame and bring it to the top. Then slide the Talentcell into the frame to hold the QMX up. You may have to be creative with the…
QMX Buddy Back Case non-destructive replacement for rear case panel. Quick to swap with existing screws to allow room for your mods. Use your slicer or cad to poke holes in where you want them. Maintains the nice aesthetic of the QMX. I…
The Almost-All-In-One is a compact, versatile PCB that plugs directly into the headphone and paddle jacks of the QRP labs QMX and QCX transceivers. The board relocates the 3.5mm jacks to the side while tapping into these circuits to add…
The Almost-All-In-One is a compact, versatile PCB that plugs directly into the headphone and paddle jacks of the QRP labs QMX and QCX transceivers. The board relocates the 3.5mm jacks to the side while tapping into these circuits to add…
A simple holder that slips over a QMX+ case to tilt it up that also has a slot to hold a M5stack Tab5 when used as a panadapter. https://github.com/SteffenLav/qmx-panadapter I printed it in PETG with supports. The attached geometry does…
This optional 3 piece end plate set provides increased stability for a plug-in style AAIO module. Versatile with many configurations options Use printed frame instead of side rail Use side rail up Use side rail down A blank plate is…
This 1 piece end plate bolts onto the left side of the QMX and provides a more secure lockup for the plug-in style AAIO. This end plate is not compatible with side rails. Check out the 3 piece design for a more modular option. Choose from…
This is the bolt on version for the AAIOv1 board. Must be installed with any 1.5-1.6mm thick plate still on the radio side. Use the factory aluminum plate, a factory side rail or either of my published end plate designs but do not use…
BACKGROUND: The QMX , (tr)uSDX and Elecraft KX2 and KX3 are fantastic portable radios, but the microphone for the KX2/KX3 is relatively big and heavy, and there really is no good mic option for the (tr)uSDX. So, I decided to design one.…
I wanted a slicker tuning knob for my new QMX radio. The conventional set screw 6mm knobs it came with were fine but I wanted something I could use to tune around by pushing with the tip of my finger rather than grabbing and turning. I…
I created this to allow for better display of the QMX (and other) magnetic backed Star Trek Cosplay badges/commbadges. You will need to print 2 of the Stand Legs. You can use this for pins with points/frogs but you will need to test place…
The model contains an alternativ volume knob and a bigger VFO Knob. Additional needed Material: 2x M2.5 x 4mm socket screw (Madenschraube) Knobs Material: PLA or PETG Layerhigh: 0,2 mm Infill: 20% Softgrip Ring In order to put the flat…
This mode is a remake of QCX-mini stand/case from thingiverse. This model fits more snugly than the original case. I used lightning infill with PETG. It made the case a bit more elastic. Still serves the purpose quite well. I attached…
This is a magnetic cover for the QRP Labs QMX radio. This uses common 6mm diameter by 2mm depth magnets. Since these are all hand built, I recommend printing the test file first. The SCAD file is included so you can make adjustments.…
Summary This Thing is a set of knobs intended to replace the knobs that come with the QCX Mini. The set includes a plain scalloped knob for volume control and a knob with a finger well to use as the VFO knob. These knobs friction fit on…
This is a bracket that is used with the CW touching keying mod for the QMX radio. Parts you will need 1) The K6ARK Capacitive touch PCB 2) 4-40 Pan head bolt, QTY 2 (Believe I used 5/16”) It was from this kit. 3) 4-40 Acron Nut, QTY 2,…
A simple little stand to hold my QRP-Labs QCX/QMX QRP CW Transceiver on my desk. It can be orientated in a 30° or 60° angle for easy viewing. In fact I may even take it to activate a POTA so the transceiver sits nicely on a park table.…
Let's face it, the standard volume and tuning knobs for the QMX, QCX, and (tr)uSDX aren't great. I set out to make them a lot better. Here's my solution. Print these top-side down, then use some M3 set screws like these…
