Goodnature A24 IoT Trap Monitor & Universal Vibration Sensor Enclosure
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Smart IoT enclosure for Goodnature A24 or general vibration tracking. Modular board sled, ESPHome & MPU6050.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 0
- Makes
- 0
- Views
- 39
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Outdoor & Garden
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
A rugged, weather-sealed modular enclosure designed to clamp directly onto the CO2 canister of a Goodnature A24 automatic rat and mouse trap—or bolt onto machinery, doors, or pumps to track vibration, cycles, and impacts.
The interior houses an MPU6050 accelerometer along with a modular mounting sled for an ESP8266 (D1 Mini) or similar board. Running ESPHome, it detects the sharp mechanical recoil shock of a trap strike in real time, automatically logs catch metrics to Home Assistant, and keeps an exact count of remaining CO2 canister shots.
Key Features
Real-Time Strike & Catch Alerts: Instant push notification the second the trap fires.
CO2 Canister Management: Tracks usage toward the ~24-strike limit of standard 16g canisters, ensuring your trap never stands unpressurized.
Modular MCU Carrier Sled: The D1 Mini mounts onto an internal carrier plate that screws into the box floor. Swap or customize the sled CAD to fit any alternative board (ESP32-C3, Seeed XIAO, Raspberry Pi Pico W, etc.).
Optimized Fastener Design: The MPU6050 and the MCU sled screw directly into self-threading plastic standoffs—no heat-set inserts required for internal electronics. Inserts are reserved strictly for high-clamping load points (the canister clamp and the outer lid).
Weatherproof Cable Entry: Designed with a dedicated port for a standard M16 cable gland, providing strain relief and keeping rain, insects, and moisture out of the electronics bay.
Universal Vibration Sensing: Don't have an A24 trap? Omit the canister clamp and bolt the flat enclosure base onto shop machines, compressors, sump pumps, or garage doors to monitor duty cycles and mechanical impulses.
Bill of Materials (BOM)
3D Printed Parts
1x Enclosure Body (ASA, ABS, or PETG)
1x Lid (ASA, ABS, or PETG)
1x Canister Clamp (ASA, ABS, or PETG)
1x MCU Carrier Sled (ASA, ABS, or PETG)
1x Lid Gasket (TPE / TPU)
2x Clamp Bolt Gaskets / Washers (TPE / TPU)
Fasteners & Inserts
2x M3 Heat-Set Threaded Inserts (pressed into the clamp tabs on the main body)
2x M3 Screws (for clamping onto the gas canister)
4x M2 Heat-Set Threaded Inserts (pressed into the outer lid posts)
4x M2 Screws (for securing the lid)
Small self-tapping / M2 screws (screwed directly into the plastic bosses for the MPU6050 and sled)
Hardware & Electronics
1x M16 Cable Gland (weatherproof/IP68 rated, suited for your power cable diameter, e.g., 4–8 mm)
1x Goodnature A24 Trap (or target machine to monitor)
1x D1 Mini (or custom board mounted to the sled)
1x MPU6050 Accelerometer / Gyro Module
1x 5V USB / Power Cable suitable for outdoor deployment
Recommended Print Settings
Filament Selection:
Body, Lid, Clamp & Sled: ASA is strongly recommended for outdoor UV and weather resistance. PETG or ABS are good alternatives for covered or indoor setups. (Avoid PLA for outdoor deployments).
Gaskets: TPE / TPU (95A or softer) to ensure proper seal compression.
Walls / Perimeters: 4 perimeters (ensures strength in the clamp ears and ample material for self-threading screws).
Infill: 25–35% (Gyroid or Grid).
Layer Height: 0.20 mm.
Supports: Print the body flat on its base. The clamp may require minimal supports depending on orientation.
Assembly & Setup Notes
Install Heat-Set Inserts: Using a soldering iron set to ~220–250°C, press the 2x M3 inserts into the clamp tabs and the 4x M2 inserts into the lid screw posts flush with the rim.
Mount Electronics: Fasten the MPU6050 and the D1 Mini sled directly into the printed plastic standoffs using small self-tapping or M2 screws (do not overtighten).
Cable Gland & Wiring: Thread the M16 cable gland into the enclosure port. Feed your 5V power cable through the gland, connect power to the D1 Mini, and tighten the gland cap to create a watertight seal and strain relief.
Fit Gaskets: Seat the printed TPE perimeter gasket into the lid channel and slide the TPE washers over the clamp screws.
Mounting:
Goodnature A24: Place the enclosure over the canister neck, align the clamp, and tighten the two M3 screws evenly until rigidly mated. Rigid mechanical contact is critical for clean recoil detection.
General Equipment: Bolt or bracket the enclosure directly to the vibrating machinery.
Firmware: Flash the board via ESPHome. Set an acceleration vector threshold ($\sqrt{x^2 + y^2 + z^2}$) to reliably trigger on the sharp mechanical strike while filtering out ambient environmental noise.
