1 / 6
Starlink Mini (UTA-231) Camper Roof Mount - Glue-On, 9 deg Tilt, Removable — image 1
1 / 6

Starlink Mini (UTA-231) Camper Roof Mount - Glue-On, 9 deg Tilt, Removable

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Glue-on roof mount for the Starlink Mini. 4 corner brackets stay on the roof, the dish comes off with 8 screws. 9 deg ti

Rating
0 / 5
Likes
1
Downloads
5
Makes
0
Views
48
Reviews
0

Updated at source:

Model information

License
Creative Commons — Public Domain

A low-profile roof mount for the Starlink Mini (model UTA-231) on a camper, van or caravan.

Four corner brackets are glued to the roof. The dish drops into them and is held by four screwed caps. Take out 8 screws and the dish comes off for use elsewhere. The brackets stay on the roof.

Features

- No drilling: brackets glue to the roof with VHB tape or a sealant-adhesive.

- Removable dish: 8x M4 screws into heat-set inserts.

- 9 deg tilt, the same angle as Starlink's own Mini Mobility Mount. Rain and dirt run off the face. Set the tilt to 0 for a flat mount.

- Low edge faces forward, so the dish is pushed down at speed instead of lifted.

- Back of the dish stays open: air flows under it for cooling, and the DC cable leaves between the brackets.

- Seat follows the sloped back of the dish. Dimensions come from Starlink's official 3D model, and the fit was checked against it.

- Every bracket fits on a small printer: 105 x 106 mm footprint. Printed in black PETG and fit-tested on a real Starlink Mini.

Hardware

- 8x M4 heat-set inserts (5.6 mm hole, up to 9 mm long, e.g. M4 x 8.1).

- 8x M4 x 10 button head screws (ISO 7380), stainless. M4 x 8 also works. Do not use M4 x 12 or longer: it bottoms out before the cap is clamped.

- Closed-cell EPDM foam tape, 1-2 mm thick, self-adhesive. A strip goes under each cap where it presses on the dish face.

- Roof adhesive: 3M VHB 5952 tape, or a sealant-adhesive such as Sikaflex 252 / 522 or Dekalin.

Print settings

- Material: ASA is best for sun and heat. PETG works well too; use an opaque color.

- Layer height 0.2 mm, 4 walls, 25 % gyroid infill, 5 top and 5 bottom layers.

- Caps: 6 walls, 100 % infill.

- No supports. Brackets print pad side down, caps flat side down, as exported.

- ASA: use an enclosure and a brim on the tall rear brackets.

Install

1. Remove the kickstand from the dish.

2. Melt the inserts into the bracket tops. Stick foam tape under each cap.

3. Put the dish in the 4 brackets and screw on the caps. The dish is the jig that sets the bracket positions.

4. Clean the roof and the pad bottoms with isopropyl alcohol. Sand the pads lightly. Use the primer your adhesive asks for.

5. Set the whole assembly on the roof, short brackets toward the front of the vehicle.

- VHB: press each pad very hard. Apply at 15 C or warmer. Full strength after 72 h.

- Sealant: lay a bead on each pad and set it down gently, keeping about 2 mm of glue under the pad. Smooth the squeeze-out into a sealed edge. Cure 24-48 h before driving.

6. Route the DC cable along the back of the dish and out between two brackets.

Before you print everything

- Print one front bracket and one cap first and test them on your dish.

- Plug in the DC cable and check it clears the roof: the center of the back sits about 15 mm above the roof.

- Re-check the screws a few times during the first hot season.

Customize

The OpenSCAD file is fully parametric and works with the Customizer. Main settings:

- TILT - tilt angle in degrees, 0 for flat.

- SLOPE - which dish side the slope runs along ("long" is lower).

- CLEAR_UNDER - space under the dish for the plug and airflow.

- CLR - side gap between dish and walls.

- PAD_GAP - gap between cap and dish face.

- ARM - bracket arm length.

- Fastener sizes (screw, insert hole, head recess).

Set PART to a part name and export the STL. Use a recent OpenSCAD build with the Manifold backend for fast renders.

Tags