1 / 7
Fits Honda ST70 / CT70 Trail 70 Intake Manifold – K&N RC-0790 Pod Filter Adapter — image 1
1 / 7

Fits Honda ST70 / CT70 Trail 70 Intake Manifold – K&N RC-0790 Pod Filter Adapter

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Intake manifold to fit Honda ST70 / CT70 Trail 70 and adapt K&N RC-0790 Pod Filter

Rating
0 / 5
Likes
0
Downloads
10
Makes
0
Views
55
Reviews
0

Updated at source:

Model information

Category
Automotive
License
Creative Commons — Attribution

Honda ST70 / CT70 Trail 70 Intake Manifold – K&N RC-0790 Pod Filter Adapter (34 mm Carb Inlet)

This manifold fits a K&N RC-0790 universal air filter to the standard Honda carburettor on the ST70 (Dax) and CT70 (Trail 70). It also suits any other carburettor with the standard 34 mm OD inlet.

The air passage is smooth all the way through and finishes in a rounded, flared inlet, a lot like a "ram charger" trumpet, so air has a clean run into the carb. The outside is shaped to follow the curves of the bike, so it looks like it belongs there and not like an add-on.

At the carb end, ridges inside and out give an air-tight seal on the inlet and stop the hose clamp slipping.

A K&N is a reusable filter, so it has to come off for cleaning now and then. That's simple here: undo the clamp and slide the filter off. The manifold stays on the carb.

Modelled from scratch.

What you'll need

  • 1 × K&N Universal Air Filter RC-0790. It comes with its own clamp for the filter end.

  • 1 × hose clamp suitable for 38 mm, for the carburettor end.

Printing

Setting

Value

Material

TPU, 95A

Layer height

0.2 mm (not critical)

Nozzle

0.4 mm (not critical)

Perimeters

3

Infill

30% gyroid (not critical)

Supports

Required, organic

Print it in 95A TPU. The flexibility is what lets the carb end seal and grip the way the original rubber intake parts do. Layer height, nozzle and infill aren't critical. Slow the print down if your extruder needs it, and keep retraction low to avoid stringing.

It needs organic supports, but it's worth a minute in the slicer rotating the model so as little support as possible is generated - 45deg works well. You'll save print time and have less to clean out of the air passage.

Fitting

  1. Remove the supports carefully, and make sure the inside of the air passage is clean and smooth.

  2. Push the carb end of the manifold over the carburettor inlet.

  3. Fit a 38 mm hose clamp over the ridged carb end and tighten it until it's secure and air-tight.

  4. Fit the K&N RC-0790 over the trumpet end and secure it with the clamp supplied with the filter.

  5. Check that everything is seated properly and nothing is pinched or touching where it shouldn't, then start the bike.

To clean the filter later, loosen the K&N clamp, slide the filter off, clean and re-oil it as K&N recommends, then refit it.

Fits

  • Honda ST70 (Dax), standard Honda carburettor

  • Honda CT70 (Trail 70), standard Honda carburettor

  • Any carburettor with the standard 34 mm OD inlet

  • Filter: K&N Universal Air Filter RC-0790

Check your carb before printing. Aftermarket and replacement carbs vary, so measure your inlet and confirm it's 34 mm OD.

If you're running one on your Dax or Trail 70, post a make. I'd like to see these little bikes breathing a bit easier.


Tags