Azimuth TH8S shifter knob: aim the grip, 24 positions, no tools
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Ergonomic TH8S knob on a 24-position spline: set the grip angle after the thread is tight, lock it with a cap.
- Rating
- 0 / 5
- Likes
- 6
- Downloads
- 4
- Makes
- 0
- Views
- 64
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Video Games
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
Every threaded knob stops wherever its thread tightens. A round knob does not care. An ergonomic one does, because the thumb dish ends up pointing anywhere. Azimuth splits the job: a core takes the official TH8S thread, and the grip sits on a 24-tooth spline, so you choose the angle after the core is tight, in 15 degree steps. A threaded cap clamps it so it cannot turn or lift. Unscrew, lift, turn, drop, tighten: ten seconds, no tools.
v1.0: validated in CAD (closed solids, no interference, Thrustmaster's design piece untouched inside the core, cap entrance and clearances checked), not yet test-printed. Fit reports are welcome and go into the next version. Minimum build: Core, Head_OnePiece, Cap and one badge.
What you get
Core: contains Thrustmaster's official design piece unchanged, so it screws straight onto the official TH8S adapter. Its 34 mm flange carries a 24-notch index ring with a long zero mark, so a setting is repeatable after you take the head off.
Head: 49 x 43 mm palm grip, 69 mm tall (top at 72 mm above the adapter block). Thumb dish 3 mm deep and about 18 mm across, 60 finger dimples on the finger sides, a pointer notch that lines up with the index ring, a recess for the grip band.
One-piece head (Azimuth_Head_OnePiece): the same head with the waffle knurl moulded in, for printers without TPU. No band needed.
Cap: 40 mm crown, M18 x 2.5 printed thread (this is the cap thread, not the adapter thread), 1.6 mm floor with a 4 mm hole underneath so the badge can be pushed out.
Band (optional): TPU 95A grip band, 2.3 mm thick, waffle knurl 0.6 mm deep, with 0.3 mm interference so it grips the recess.
Knob height is 83 mm above the adapter block (84 mm with the badge relief). Print it in any two colours: dark grey and red as rendered, orange, white, whatever matches your rig.
Extras
Badges: 22 mm discs, 2 mm thick (1.2 mm base plus 0.8 mm relief; the blank is 1.2 mm). 7+R gate map (default), compass rose (24 rim ticks for the 24 positions), PRUSA wordmark, and a blank for your own initials or number. Light press fit in the cap pocket; sand the edge if your printer runs tight.
Ballast: a ring pocket in the head, 5 mm wide and 11 mm deep, takes about 15 g of 4.5 mm steel BBs (they sit one wide, two high) or about 30 g of fine lead shot. Top it with a sliver of foam so nothing rattles.
Printing
0.4 mm nozzle, 0.2 mm layers, no supports on any part. Times and weights are from OrcaSlicer 2.4 with the settings below on a Creality K1 Max profile (0.2 mm layers); your printer will differ. Whole knob with the band: about 100 g and 4.5 hours.
Core: flange down (cavity opening on the bed); PLA or PETG; 5 / 30 % walls / infill; 41 g, 1h 30m.
Head: base down (spline opening on the bed); PLA; 5 / 15 % walls / infill; 45 g, 1h 37m.
Cap: flat side down; PLA; 4 / 20 % walls / infill; 7 g, 17 min.
Badge (each): flat, relief up; contrast PLA; 3 / 100 % walls / infill; 0.8 g, 3 min.
Band: standing; TPU 95A, 25 mm/s, retraction off; 2 / 100 % walls / infill; 7 g, 53 min.
One-piece head (instead of Head + Band): base down; PLA; 5 / 15 % walls / infill; 46 g, 1h 38m.
Printability notes:
Steepest outside overhang is 34 degrees, on the 1.5 mm lead-in at the base of the head; the bulge is 16 degrees; dimples are 0.8 mm deep.
Three internal spans print without support and are hidden: the 2 mm ledge above the band recess (under the band), the 4 mm ring ceiling over the spline socket (1.2 mm above the core, so a little droop cannot hold the head off the flange), and the cap floor, which bridges the 18.5 mm thread bore at 8.4 mm height.
Tolerances are built in: 0.2 mm radial on the bore and spline, 0.25 mm radial on the cap thread, 0.08 mm radial on the badge. If the head or the cap runs tight, scale that part to 100.5 % in X and Y. Never scale the core: its cavity is the official thread. Use 0.15 to 0.2 mm elephant-foot compensation on the core, because the official thread starts on the first layer.
Two-tone badge: print it in the accent colour and swap filament at 1.2 mm height, so the relief comes out in a second colour.
Assembly (no tools, no glue)
Fit the official adapter to the TH8S as the PDF in Thrustmaster's official files (model 1825116) shows.
Screw the core on until its flange seats on the adapter block.
Band: stretch it over the base of the head from below and into the recess (TPU only; it stretches about 20 % on the way).
Drop the head onto the spline with the thumb dish under your thumb. Note which index notch sits under the pointer; the long notch is zero. To change it, lift the head, turn it one or more notches, drop it back.
Optional: fill the ring pocket with 4.5 mm steel BBs (about 15 g) or fine lead shot (about 30 g) and top it with a sliver of foam so nothing rattles.
Screw the cap down hand-tight, then press the badge in so the gate map reads upright (the cap stops at a new angle after every change; the badge does not care). To swap or straighten a badge, unscrew the cap and push the badge out through the hole underneath. If the cap ever works loose, a wrap of PTFE tape on the stub fixes it.
Fit to the official adapter
The core embeds the design piece from Thrustmaster's official TH8S gear knob files, verified in CAD: the complete piece lies inside the core, and the cavity thread (about M18, 1.6 mm lead) and spigot bore are untouched. Nothing to buy except the adapter itself: Thrustmaster's official TH8S gear knob files.
Files
STL and 3MF for every part: Azimuth_Core, Azimuth_Head, Azimuth_Head_OnePiece, Azimuth_Cap, Azimuth_Sleeve_TPU, Azimuth_Badge_GateMap, Azimuth_Badge_Compass, Azimuth_Badge_Prusa, Azimuth_Badge_Blank. For remixing: a STEP for every part except the one-piece head and the knurled band (their B-rep files are over 200 MB, so they are STL and 3MF only), plus Azimuth_Assembly.step with a plain band and Azimuth_Sleeve_TPU_plain.step.
Credits and licence
Design, CAD, renders and documentation: Kareem Hassan. Remix of THRUSTMASTER : Official TH8S Gear knob files (model 1825116) by Thrustmaster, used under CC BY-NC-SA; this model is published under the same licence. The PRUSA wordmark on the optional badge is a trademark of Prusa Research, taken from their media kit for this Prusa-hosted contest. Entry for the Thrustmaster Custom Shifter Knob contest.
