1 / 5
FRITZ!Box 7690 / 7590 / 7590 AX Wall Mount – 20 mm off the wall (Wandhalterung) — image 1
1 / 5

FRITZ!Box 7690 / 7590 / 7590 AX Wall Mount – 20 mm off the wall (Wandhalterung)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Hangs the FRITZ!Box 7690 / 7590 / 7590 AX 20 mm off the wall on its own keyholes. All ports stay free. No supports.

Rating
0 / 5
Likes
1
Downloads
8
Makes
0
Views
53
Reviews
0

Updated at source:

Model information

Category
Electronics
License
Creative Commons — Attribution — Noncommercial — Share Alike

🇬🇧 English below · 🇩🇪 Deutsch weiter unten

English

Screwed straight to the wall, a FRITZ!Box sits with its vented underside almost flat against the plaster. This bracket holds it 20 mm off the wall so air can flow behind it, and it uses the box's own two keyholes – nothing to clamp around the housing, no straps.

The box hangs with its ports facing down, the way AVM specifies for wall mounting. The frame is completely hidden behind the box, and nothing sits below or beside it, so DSL, phone, LAN and power stay fully accessible.

Fits

  • FRITZ!Box 7690 – printed and in use

  • FRITZ!Box 7590 and 7590 AX – same housing and keyhole spacing, fits as well

How it works

  • Two hooks at the top carry the whole weight. Each one sits on a slanted bracket like a shelf support, so it doesn't bend under load.

  • The neck in the keyhole slot is elongated, not round. The box is hung from above, so the load runs along the slot – the neck uses the full slot length for a much stronger cross-section than a round pin. Head and neck together still pass through the 10 mm opening.

  • Two round pads at the bottom sit exactly under the rubber feet and keep the box from tipping towards the wall.

  • The frame is a trapezoid: wide at the hooks, narrow at the feet.

Mounting

  1. Hold the frame against the wall, hooks at the top, and level it.

  2. Mark the four holes, drill, fit wall plugs.

  3. Screw it on with four 4 mm countersunk screws.

  4. Hang the box: ports down, underside towards the wall. Put the keyholes over the hook heads, push in and let it slide down a few millimetres. The rubber feet come to rest on the pads.

The frame is its own drilling template – no measuring between the keyholes.

Specifications

Frame

212.5 × 133 mm, 26.5 mm deep

Wall gap

20 mm to the underside of the box

Hooks

196.5 mm apart (keyholes are 197 mm)

Hook head / neck

Ø8.5 mm / 4.5 × 7 mm slot shape

Pads

Ø20 mm, 175 mm apart (= rubber feet)

Screws

4 × 4 mm countersunk (hole 4.5 mm, countersink Ø9)

Material

about 77 cm³ solid volume

Print settings

  • The STL is already in print orientation: wall side on the bed, hooks and pads pointing up. No supports – the hook heads have a 45° underside.

  • PETG, 4 perimeters, 25 % infill.

  • Fits a 220 × 220 bed.

This is version 3. My first print reached far below the box and the pads missed the rubber feet. I measured on the real box (feet 175 mm apart, 117 mm from the top of the keyhole slot to the centre of a foot) and narrowed the frame at the bottom. The hooks were also slightly tight at 197 mm, so they are now 196.5 mm apart and slide in without binding. This version is printed and holds my 7690 on the wall.

Adapting it

The OpenSCAD file is included and works with the Customizer. The main values at the top:

  • wall_gap – distance between wall and box

  • hole_spacing – distance between the hooks

  • slot_top_to_foot – top end of the keyhole slot to the centre of a rubber foot

  • foot_spacing – rubber feet, centre to centre

  • head_d, neck_w, neck_h, neck_l – hook head and neck; checked automatically so they still fit through the keyhole

  • part = "assembly" shows the bracket with a simplified box, part = "hook" a close-up of one hook.

License

CC BY-NC-SA 4.0. Share it, remix it, print it for yourself and your friends – just credit me and release your version under the same licence. Commercial use of any kind requires my written permission, including selling prints. Just send me a message.


Deutsch

Direkt an die Wand geschraubt liegt eine FRITZ!Box mit ihrer gelochten Unterseite fast flach am Putz. Dieser Halter hält sie 20 mm vor der Wand, damit dahinter Luft zirkulieren kann – und zwar an ihren eigenen beiden Schlüssellöchern. Nichts umklammert das Gehäuse, keine Bänder.

Die Box hängt mit den Buchsen nach unten, so wie AVM es für die Wandmontage vorsieht. Der Rahmen verschwindet komplett hinter der Box, und unter oder neben ihr ist nichts – DSL, Telefon, LAN und Strom bleiben frei zugänglich.

Passt für

  • FRITZ!Box 7690 – gedruckt und im Einsatz

  • FRITZ!Box 7590 und 7590 AX – gleiches Gehäuse und gleicher Lochabstand, passt ebenfalls

So funktioniert es

  • Zwei Haken oben tragen das ganze Gewicht. Jeder sitzt auf einer schrägen Konsole wie bei einem Regalträger und biegt sich nicht durch.

  • Der Hals im Schlitz ist länglich, nicht rund. Die Box wird von oben eingehängt, die Last läuft also entlang des Schlitzes – der Hals nutzt die Schlitzlänge und hat deutlich mehr Querschnitt als ein runder Stift. Kopf und Hals passen zusammen trotzdem durch die 10-mm-Öffnung.

  • Zwei runde Polster unten sitzen genau unter den Gummifüßen und halten die Box auf Abstand, damit sie nicht zur Wand kippt.

  • Der Rahmen ist ein Trapez: breit an den Haken, schmal an den Füßen.

Montage

  1. Rahmen an die Wand halten, Haken oben, mit der Wasserwaage ausrichten.

  2. Die vier Löcher anzeichnen, bohren, Dübel setzen.

  3. Mit vier Senkkopfschrauben 4 mm festschrauben.

  4. Box einhängen: Buchsen nach unten, Unterseite zur Wand. Schlüssellöcher über die Hakenköpfe setzen, andrücken und ein paar Millimeter nach unten rutschen lassen. Die Gummifüße liegen dann auf den Polstern.

Der Rahmen ist gleich seine eigene Bohrschablone – kein Ausmessen der Lochabstände.

Maße

Rahmen

212,5 × 133 mm, 26,5 mm tief

Wandabstand

20 mm bis zur Unterseite der Box

Haken

196,5 mm Abstand (Schlüssellöcher 197 mm)

Hakenkopf / Hals

Ø 8,5 mm / Langloch 4,5 × 7 mm

Polster

Ø 20 mm, 175 mm Abstand (= Gummifüße)

Schrauben

4 × Senkkopf 4 mm (Loch 4,5 mm, Senkung Ø 9)

Material

rund 77 cm³ Vollvolumen

Druckeinstellungen

  • Die STL liegt bereits in Drucklage: Wandseite aufs Bett, Haken und Polster zeigen nach oben. Keine Stützen – die Hakenköpfe haben eine 45°-Unterseite.

  • PETG, 4 Wandlinien, 25 % Füllung.

  • Passt auf ein 220 × 220-Bett.

Das ist Version 3. Mein erster Druck ragte weit unter die Box, und die Polster lagen neben den Gummifüßen. Ich habe an der echten Box nachgemessen (Füße 175 mm auseinander, 117 mm von der Oberkante des Schlitzes bis Mitte Fuß) und den Rahmen unten schmaler gemacht. Außerdem klemmten die Haken bei 197 mm leicht – jetzt sind es 196,5 mm, und sie gleiten ohne Zwängen hinein. Diese Version ist gedruckt und hält meine 7690 an der Wand.

Anpassen

Die OpenSCAD-Datei liegt bei und funktioniert mit dem Customizer. Die wichtigsten Werte am Dateianfang:

  • wall_gap – Abstand zwischen Wand und Box

  • hole_spacing – Abstand der Haken

  • slot_top_to_foot – Oberkante Schlitz bis Mitte Gummifuß

  • foot_spacing – Gummifüße, Mitte zu Mitte

  • head_d, neck_w, neck_h, neck_l – Hakenkopf und Hals; eine eingebaute Prüfung stellt sicher, dass beides noch durchs Schlüsselloch passt

  • part = "assembly" zeigt den Halter mit vereinfachter Box, part = "hook" einen Haken im Detail.

Lizenz

CC BY-NC-SA 4.0. Teilen, verändern, für dich und deine Leute drucken – gerne. Nenn mich als Urheber und stell deine Fassung unter dieselbe Lizenz. Jede kommerzielle Nutzung bedarf meiner schriftlichen Genehmigung, auch der Verkauf von Drucken. Schreib mich einfach an.

Tags