1 / 7
Honeycomb Spray Can Wall for Skadis (seamless tiling, lock cleat) — image 1
1 / 7

Honeycomb Spray Can Wall for Skadis (seamless tiling, lock cleat)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Modular honeycomb spray can wall for Skadis. Tilted cells, lock cleat rails, seamless tiling, no supports.

Rating
0 / 5
Likes
6
Downloads
8
Makes
0
Views
70
Reviews
0

Updated at source:

Model information

Category
Garage
License
Creative Commons — Attribution — Noncommercial — Share Alike

Spray cans are awkward to store: they roll, they tip, and the one you want is always in the back. This system holds every can at an angle with its cap facing out, so you see every color at a glance and grab what you need with one hand.

Features

  • Seamless honeycomb: each module’s outer walls are half walls, so modules placed side by side or stacked form one continuous hex grid.

  • Tilted 5° upward: cans settle back against the wall on their own and can’t roll out.

  • Lock cleat rails: modules drop in behind a tongue on the rail, so a bump or a heavy can can’t pop them off. They only come off when you lift them straight up.

  • Slides anywhere: modules slide along the rails, so you can shift each row half a cell for true hex packing, no matter where the pegboard holes fall.

  • Prints without supports: stretched-hex windows with built-in corner gussets keep it light and stiff. The only bridges are short 10 mm ones.

  • Board-safe mounting: the rails bolt on with standard Skadis T-nuts and have alignment guides on the back, with no hooks to stress the board.

Fits: standard 66 mm (2.6 in) diameter spray cans, like Rust-Oleum 2X, Universal, and Automotive. Print the fit test first if your cans are a different brand.

Size: each module holds 2 cans and is 156 mm wide by 107 mm deep. Rows sit 60 mm apart on the wall.

What to print (per module)

  • 1x can_module_v10

  • 1x can_rail_v10

  • Optional: can_fit_test_v10 (a 15-minute check that your cans slide in and the cleat fits)

Hardware (per rail)

  • 2x Skadis T-nuts, with M3 x 12-14 screws (threaded T-nuts) or M2.5 x 15 screws (hex-nut T-nuts)

See the original Skadis T-nut model page for detailed documentation of what they are and how to use them:

 https://www.printables.com/model/228663-skadis-t-nuts-mounting-system-for-ikea-skadis-pegb

Print settings

  • Material: PLA Basic (shown in black). PETG works too.

  • Nozzle: 0.6 mm recommended. The walls are sized for 0.6 mm lines and it prints much faster than with a 0.4.

  • Layer height: 0.42 mm works great.

  • Walls: 2

  • Supports: none

  • Orientation: as exported. The module prints back face down, and the rail stands on its bottom edge.

Install

  1. Bolt the rails to the board, two T-nuts per rail. Space each row of rails 60 mm apart vertically. On the hole grid, rails end up about 160 mm apart center to center, and a small gap between rails is fine.

  2. Hang the bottom row first and work up. Set each module’s hooks over the rail and drop it down behind the tongue.

  3. Shift every other row half a cell (39 mm) sideways to get the honeycomb look.

  4. To remove modules, work from the top down. Lift a module about 7 mm to clear the tongue. The row above blocks this, which is also what keeps everything locked in place.

Customize it

The included OpenSCAD file is fully parametric: can diameter, tilt, cells per module, wall thickness, window style, cleat dimensions, and more. It’s set up for the customizer if you want to adapt it to other cans.

Tags