1 / 4
HHO generator — image 1
1 / 4

HHO generator

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

water is boring and the good stuff is behind a paywall 1.23 Volts, pay that fee righ now with this cell.

Rating
0 / 5
Likes
0
Downloads
2
Makes
0
Views
29
Reviews
0

Updated at source:

Model information

License
Creative Commons — Public Domain

This is an oxy-hydrogen electrolisis cell, you might have heard of it as a magical device that creates fuel out of water..... thats bs.

Safety and general tips:

Do a little research on safety precautions when dealing with caustic solutions, for HHO cells don't use a acid elelctrolyte, and be responsible when handling the HHO mixture, if  you are planing on using NaOH as you electolyte make sure that every 3d print that touches it is either made of PE or PA, don't try to 3d print the PVC pipe that is just an increased risk of leaks and use sealent across the whole bottom and top caps not just on the mates.

Hardware:

You can use any power supply you want just make sure you are getting around 1.9-12  vots per cell, when using higher voltages i.e. >4V be mindfull of efficinecy losses wich get converted into heat wich you 3d prints nor you electrolyte want, but it should be fine for short runs as there is plenty of thermal capacity as you will use around 600ml of electrolyte per cell. The bracket is made for HP server power supplies wich are probably the best afordable high current power supplies you can get, they are much easier to handle and get runing than something like a microwave transformer, DON'T buy them new you can get them sometimes as low as 1200W for 20$ from crypto mining, don't be affraid of buying a used PSU you are not building a PC with it, if you can buy from a seller who can sell you multiple PSUs of the same model, joining their output is much easier than if they are dissimilar. These PSUs won't turn on when you connect power, most of the times just short the first 3 small gold plates on the edge of the board, drop a solder drop there its easier to swithch power upstream of the PSU. I know high current is fun to play with,  just make sure that if there is an overcurrent protection shut off let the PSU rest for at least 5 minutes, l already killed one just by turning it on again.

There  is around 1000cm^2 of electrode area, when using 316 stainless as a electrode so thats good up to around 500A or 5 1200W PSUs, i will be using only 200A as that way there is less heating and more efficiency, if you are thinking of runing with the full 500A make sure you are not using higher voltages, stick to under 3V and consider a electrolyte coller.

If you are using 304 stainless consider lowering the current, 300A should be your maximum for prolonged exposure, don't consider any other electrode material, nickel and anything more noble is overkill and most other metals leave you with a chemical goo after some minutes, wich if you are burning the HHO turns this clean flame into a chemical hazard on the chemical hazard side don't use table salt that decomposes into chlorine, if you want a less harmfull electrolyte than NaOH use NaHCO3 i.e. baking soda.

As for other materials you will need are as follows: at least 12cm of 110mm inner diameter PVC pipe per cell, a 70cm section for the 6 cells, 10 M6 screws +4 per cell 34 total, the type os screw isn't important but countersunk looks refined and it isn't more expensive, each cell needs a 1/2'' NPT fitting to connect to your flexible hose of choice, as well as 21 100mmX100mm 316ss sheet between .3 and 1 mm thickness works 126 for the 6 cells, 46 M8 nuts per cell 276 total with 35cm of threaded rod to match on each cell 210cm total.

Construction:  

Print every part starting with Electrolysis cell - ... 1 for each cell you plan on making and the included PSU bracket, it works with either 1 or 2 PSU's so you can scale this project down in half and only increase production if it doesn't fit you, no parts need supports. Cut the drill the 2 8mm holes metal sheets clamp every sheet of the same cell together and most use a sacrificial piece of wood at the back this is especilay important with tinner stock one hole sits 9mm from the center line and the other 24mm both 9mm form the edge of the material, the 2 square cutouts are placed exacly the same on every plate so you can save time by cutting them all together with a band saw or an angle grinder they are 18mmx18mm and are located as to mirror the holes you just drilled.

Next step is to cut your threaded rods into 85mm sections and place 4 of them in a row,  add a nut to each one and screw 2 of them about 4mm in, add you first electrode as to make the nuts you screwed further in land on the cutouts, the next sheet should be fliped as to have its cutouts on the oposite nuts leaving a gab about  4mm between them add the next 4 nuts and get everything pretty tight as you lose access to the nuts, add another sheet with the same orientation as the first one, repeat untill you have 21 sheets, you dont have to count them just keep on going until you run out of room for more. 

If you have a thick gauge wire and can crimp a lage terminal do so,  if not you can crimp a small wire to each plate and run the wire out of the lid wich you should then tack in place hot glue, coat the bottom cap also with hot glue and insert it into the 12cm PVC pipe sections. Now add the spacer at the bottom of you sheet stack and insert it on the pipe and seal it from the outside, get some sealant  on you NPT fitting and get yourself a wrench as you will be cutting the thread into the plastic get yourself a baseplate and screw the M6 screws into the holes at the bottom of both the cells and the rack, slide your PSU's into the rack and they should latch, it takes some force but you can help it by pushing the bar on the PSU, as mentioned before you should put a drop of solder on the first 3 small pins, now you can solder your wires into the tick terminals if you have a low power soldering iron you may strugle you can make your life easier by helping it with a lighter or a blowtorch using with the smalest flame you can.