1 / 7
Rotating Spiral Spice Tower – Helix Stair, 20 Round Jars on a 200 mm Tray, Turns on 608 Bearings — image 1
1 / 7

Rotating Spiral Spice Tower – Helix Stair, 20 Round Jars on a 200 mm Tray, Turns on 608 Bearings

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

A turning spiral staircase for your own round spice jars: 20 jars (46 x 100 mm) or 16 tall ones on a 200 mm tray.

Rating
0 / 5
Likes
2
Downloads
6
Makes
0
Views
54
Reviews
0

Updated at source:

Model information

Category
Kitchen
License
Creative Commons — Attribution — Noncommercial

Helix Stair is a turning spice tower for your own round jars: a spiral staircase around a slim core, 8 jars per turn, each on its own tread with a low lip. It is printed as identical half-turn helix modules that screw together like brickwork, a rotor with two 608 skate bearings on a fixed M8 spindle, a crown that caps the core and a 200 mm tray on small adhesive bumpers. The tower turns; the tray stays still.

Validation status (please read): digitally validated only - checked in CAD (jar fit, a lift-and-slide removal sweep for every jar, derived stability) and in the slicer (no supports). It has not been physically printed or tested. Print the fit coupon first. All pictures are renders of the CAD model or drawings; the jars, spices, counter and wall are generic stand-ins - none is a photograph.

Two sizes

  • STANDARD: round jars up to 46 mm across and 100 mm tall (lid included) - 20 jars, 5 modules, about 414 mm tall.

  • TALL: round jars up to 46 mm across and 116 mm tall (the common ~45 x 115 mm glass spice-jar size) - 16 jars, 4 modules, about 400 mm tall.

Both turn within 192 mm on a 200 mm tray (a bed of at least 210 x 210 mm is needed). Measure the widest part of your jars, lid included, and their height with the lid. Square jars are not supported by the supplied files.

Features

  • Real bearings: two 608 skate bearings 23 mm apart on the plain shank of a partially threaded M8x90 bolt, with a small designed axial play (designed for a smooth, low-wobble turn; not yet tried on a printed part).

  • Lift a jar about 5 mm and slide it straight out toward you: every jar's lift-and-slide path was swept on the CAD model against the whole tower with no contact, with about 18 mm of headroom under the step above.

  • Jars sit in a lip ring on treads that slope 2° toward the core, so each jar leans slightly inward.

  • No supports: each module lies on its flat seam face, so the treads stand up as walls; slopes are 45° or less from vertical.

  • Identical modules - print the same file five times (tall: four). They alternate sides like brickwork, the seams sit in the risers, and the joints are socket screws in recessed counterbores (no nuts).

Which files?

  • Ready-to-print PrusaSlicer projects with per-part layer heights set: helix_spice_tower_complete.3mf (STANDARD, 7 beds) and helix_spice_tower_tall_complete.3mf (TALL, 6 beds), plus one project per plate (00 fit coupon, 01-05 modules, 06 tray, 07 rotor + crown + sleeves; tall 01-06).

  • STL files for both sizes: helix module, plinth (the tray), rotor, crown, spacer sleeve, race cap and fit coupon.

  • model.py - the CadQuery source: jar diameter, jar height and jar count (8 per turn, or 6 for wide jars). python model.py --jar-d D --jar-h H --check prints the layout and runs the fit, removal and stability checks for your numbers (needs CadQuery plus trimesh, shapely, networkx, manifold3d, scipy and rtree). Other sizes are not validated.

Print settings

  • PETG for every part (the rotor carries the bearings and the whole tower).

  • 0.4 mm nozzle, 3 perimeters, no supports. 0.3 mm layers for the modules, tray and crown; 0.2 mm for the rotor (bearing seats), sleeves and fit coupon - already set per part in the projects.

  • Modules lie on their flat seam face (as in the files); keep elephant-foot compensation on so the seam faces stay flat. Clean bed or glue stick for the long thin first layers; no brim is set - add a 3-5 mm brim if your printer needs one.

  • STANDARD about 416 g and 31 h 52 min over 7 plates (longest plate 4 h 46 min); TALL about 370 g and 27 h 51 min over 6 plates. PrusaSlicer 2.9.6 estimates on a generic PETG profile - faster printers print much quicker.

Hardware

  • 2 x 608-2Z (608ZZ) bearings

  • 1 x M8x90 hex bolt, partially threaded (ISO 4014 / DIN 931, 22 mm thread) - a fully threaded bolt puts the bearings on the thread

  • 1 x M8 nyloc nut (DIN 985) and 1 x M8 washer (DIN 125)

  • 12 x M4x8 socket-head screws (ISO 4762; TALL: 10) - they cut their own thread in the printed pilot holes

  • 20 x self-adhesive bumpers about 10 mm across and 3 mm high

Assembly (about 30 minutes; 3 mm hex key, 13 mm spanner)

  1. Print the fit coupon first (608 seat ring, spindle ring, M4 counterbore + pilot boss) and check the fits.

  2. Stick the 20 bumpers on the dots under the tray. Push the M8 bolt up through the tray from below (head in the hex pocket).

  3. Press one 608 into the rotor from below until it stops on its shoulder; lower the rotor over the bolt so that bearing rests on the tray's land.

  4. Drop the spacer sleeve down the bolt, slide the second 608 down and start it into the rotor's top seat by hand. Add the race cap, the washer and the nyloc; tighten until snug on the spacer stack, then stop - more torque only squeezes the plastic. Never press a bearing in with a socket. The rotor must turn freely.

  5. Module 1 sits on the rotor flange and screws to it with 2 screws; the next modules alternate sides, each screwed to the one below with 2 screws; then the crown (2 screws). Turn each screw in until the head seats and stop.

  6. Load the jars from the bottom up, all the way round, so the tower is never heavy on one side.

Use: turn the tower by hand at a calm pace. To take a jar, lift it about 5 mm and slide it straight out; put it back the same way.

Limitations

  • Digitally validated only: not physically printed or tested.

  • A tall, narrow object: derived from the CAD with 200 g jars, a sideways push at the top of about 9 N (standard) or 8 N (tall) tips the full tower and about 1 N an empty one. Keep it back from the counter edge and out of reach of children.

  • Turn it calmly and load it evenly: derived from the CAD, a full jar tips out of its lip at about 1.3 turns per second, and a lopsided load overturns the tower at about 1.1 turns per second. Never spin it fast with only a few jars on one side.

  • The steps are 1.3 mm printed shells made to hold jars: do not lean on them, press on the step edges or use the tower as a handle (no load check has been made). Designed for 20 small jars of about 200 g each.

  • The back shows the rotor's 2 screw heads, the crown's 2 screw bosses and the end of the top step; the images show the front.

  • The printed parts are not food-contact parts - spices stay in their own closed jars. Wipe clean with a damp cloth; no dishwasher, no soaking; keep it away from the hob and the oven.

Pictures

Renders of the CAD model and drawings, not photographs: the loaded tower on a counter (cover), the tower on a studio background, the lift-and-slide removal, the modules exploded, the two sizes, the top view and a module as printed. Jars and spices are generic stand-ins.

Tags