1 / 4
Portable Monitor Portrait Stand – Holds Only the Corners, Plug Hangs Free, Bare or Cover-On (13–16 in) — image 1
1 / 4

Portable Monitor Portrait Stand – Holds Only the Corners, Plug Hangs Free, Bare or Cover-On (13–16 in)

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Stands a 13-16 in portable monitor in portrait beside your laptop, held only by its bottom corners; the plug hangs free.

Rating
0 / 5
Likes
1
Downloads
1
Makes
0
Views
41
Reviews
0

Updated at source:

Model information

Category
Office
License
Creative Commons — Attribution — Noncommercial

A portrait stand for 13.3-16 in USB-C portable monitors that have no portrait kickstand (folio or smart-cover models, which usually prop up in landscape only). The monitor stands upright beside your laptop, leaned back 13°, and rests only on its two bottom corners, which sit on one concave arc (R 280 mm) - every panel 188-238 mm wide seats on the same arc. The straight bottom edge, where the plug and buttons usually are, hangs free over an open bay: a straight USB-C plug hangs into it and the cable leaves through the base. The seat floor is heeled - it falls 22° toward the back - so the monitor's own weight keeps its bottom edge in the corner: the lean is held by the shape, not by friction (calculated). Nothing is clamped or stuck to the monitor.

Validation status (please read): checked in CAD (widths 188-238 mm in 2.5 mm steps, heights, thicknesses and masses across the stated ranges; plug bay sweep; calculated statics) and in the slicer. It has not been physically printed or tested - please report. Images are renders of the CAD model and drawings from it, not photographs; the monitor and laptop in the images are generic stand-ins. No monitor brand or model is named.

Features

  • Held only by its two bottom corners (calculated for every width 188-238 mm, corner radius 3-8 mm): the straight bottom edge more than 15 mm from each corner stays at least 2.9 mm from the stand.

  • Open plug bay: a straight USB-C plug hangs free (at least 2.5 mm clearance, calculated) if the port is at least 17 / 30 / 42 mm from a corner on a 188 / 213 / 238 mm wide panel. The cable runs back across the base plate and out through the rear notch.

  • Holds by its shape (calculated for every case): the heeled floor holds the lean with no friction at all (22° heel, at most 18° needed), and the monitor's centre of mass sits 64-76 mm below the arc's centre, so it cannot slide off sideways. It does not level itself - set it level by eye (about 1.1° of tilt per 5 mm off-centre).

  • Two files: bare monitors 4-12 mm thick, or cover on (a cover that folds flat behind the monitor) 12-20 mm.

  • Two halves + three glued bowtie keys: each half fits a 220 x 220 mm bed; no supports, no screws.

Will my monitor fit?

Portable monitors 188-238 mm wide in portrait (the bottom edge), 300-380 mm tall and 0.6-1.0 kg - check your monitor's spec page. Bottom-edge ports must sit at least 17-42 mm from a corner (by panel width); otherwise stand the monitor ports-up and run the cable down the back. Right-angle plugs were not checked. Monitors with a built-in portrait kickstand do not need it.

Dimensions

Assembled 246 x 206 mm footprint, 165 mm tall; each printed half 123 x 206 mm. Seat: R280 arc, 13° lean, floor heeled 22°; groove 13 mm (bare file) or 21 mm (cover file); back contact on two lobes up to 116 mm up the monitor.

Which files?

  • Print both plates of your file - bare: sidescreen_bare_complete_plate1.3mf (right half + 3 keys; 7 h 22 min, 104 g) and _plate2.3mf (left half; 6 h 49 min, 97 g); cover: sidescreen_cover_complete_plate1.3mf (7 h 42 min, 110 g) and _plate2.3mf (7 h 10 min, 102 g). PrusaSlicer 2.9.6 estimates on a generic PLA profile.

  • STL files: bare_half_left / bare_half_right, cover_half_left / cover_half_right and bowtie_key (print 3).

  • model.py - the parametric CadQuery source: lean, arc radius, heel, groove, lip, lobes, base.

Print settings

  • Matte PLA or PETG (switch the filament profile for PETG); any colour - the keys can be a contrast colour.

  • 0.4 mm nozzle, 0.2 mm layers, no supports. Halves upright on their base as they stand on the desk (10 % infill is enough - they are mostly walls); keys flat.

Assembly

Put the two halves together on the desk, split faces touching, and drop the three bowtie keys into their pockets (a slip fit - do not force them). Then glue them: a few drops of CA (gel) or 2-part epoxy in each pocket and along the split faces (epoxy for PETG). Gluing is required - it makes the stand one rigid piece, and the calculated stability assumes it.

How to use it

  1. Plug the cable into the monitor first.

  2. Lower the monitor in portrait, centred between the two corner piers, with its back against the two lobes until both bottom corners sit on the floor. If the bottom edge ends up forward in the groove, the monitor rests more reclined (up to about 19°, calculated) - push it back into the corner.

  3. Set it level by eye. Lay the cable back across the base plate and out through the rear notch.

Limitations

  • Not physically printed or tested; fit, clearance and stability are calculations on the CAD.

  • For viewing, not touch: calculated, a sideways push of 1.3-3.6 N at a top corner lifts the monitor off one corner; about 2.4 N normal to the screen at the top tips the stand back (0.6 kg monitor); a forward pull of about 0.7 N at the top tips the monitor forward out of the seat.

  • Monitors outside 188-238 mm wide, 300-380 mm tall or 0.6-1.0 kg, and covers thicker than 20 mm, were not checked.

  • Two halves + three keys - the keys must be glued.

Images are renders of the CAD model and drawings from it, not photographs; the monitor and laptop in the images are generic stand-ins. No monitor brand or model is named.

Tags